Hi, If you don't want to read the whole story, I'm curious about how I can re-set all of the settings for the network (for instance if everythign was broken that you debug going through the list from the "HOWTO - Basic Network Troubleshooting / Understanding"): - Is the interface configured correctly ? (lspci, lsmod, dmesg, ifconfig /etc/network/interfaces) - Is/Are DNS / hostnames configured correctly ? (Bind, /etc/hosts, /etc/resolv.conf) - Are the ARP tables correct ? ( arp -a ) - Can you ping the localhost ? (ping localhost / 127.0.0.1 *try both*) - Can you ping other local hosts (hosts on the local network) by IP Address? How about hostname? (ping) - Can you ping hosts on another network (ala internet) ? (ping) - Do applications like ssh, firefox, sftp, etc, work ? (chosen application)
If there's no good way to do that or if it's a huge task, then here are the symptoms for my problem(s): I have an HP Pavilion with what seems to be all nVidia cards inside it, which has been giving me trouble since last week when I decided to install Debian. I struggled for hours with the net install and finally remembered that I had a spare network card in my garage. After plugging that in, the network install worked fine, but eth0 has been inactive. Last night I decided to get the nVidia nForce card (nVidia Corporation nForce Ethernet Controller (rev c2)) up and running. I don't even remember what I did, but I stumbled across enough information advising me to upgrade the kernel to 2.6 (from 2.4.27-2-386) that I gave up on whatever I was trying. Now my short term goal is to get the 3com ethernet card working again (3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)). Then I can apt-get to upgrade the kernel. The merits of Debian quickly disappear when I'm stupid enough to hose my network connection, disabling apt-get. I would be content to run the network configuration that I ran when I first installed Debian. I searched for a while on the internet to figure out how to do this, but then gave up. Otherwise, it would be fine to fix the actual problem if that can be done easily. I'm nearly ready to format and re-install, but I have actually done some useful things on the computer, including backing up my Mac (which is concurrently on the fritz). I have run "dpkg-reconfigure etherconf" multiple times, both setting up the 3com card with DHCP and statically. Currently, under DHCP my system is capable of getting an IP address from my router -- or at least it leads me to believe it is: Listening on LPF/eth1/00:01:02:36:6b:ef Sending on LPF/eth1/00:01:02:36:6b:ef Sending on Socket/fallback/fallback-net DHCPREQUEST on eth1 to 255.255.2552.55 prot 67 DHCPACK from 192.168.1.10 bound to 192.168.1.102 -- renewal in 43200 seconds. Note that 192.168.1.10 is the host -- I changed it from .1 after reading something that seems not to have applied. I am able to ping all of localhost, 127.0.0.1 (which is localhost), and 192.168.1.102 (which is also the same machine). I am able to broadcast ping 127.0.0.0, but not 192.168.1.0 (the same is true with .255 instead of .0). When I try to broadcast ping I get: ping: sendmsg: Operation not permitted ping: sendmsg: Operation not permitted ... Not only can I not broadcast ping, but I cannot ping the host by number -- with the exception of testing localhost, I have been attempting to ping using ip addresses and not names (the same is true with the setup through dpkg-reconfigure etherconf). Here's what I get when I try to ping the host: /home/rls# ping 192.168.1.10 PING 192.168.1.10 (192.168.1.10) 56(84) bytes of data From 192.168.1.102 icmp_seq=1 Destination Host Unreachable From 192.168.1.102 icmp_seq=1 Destination Host Unreachable From 192.168.1.102 icmp_seq=1 Destination Host Unreachable From 192.168.1.102 icmp_seq=1 Destination Host Unreachable From 192.168.1.102 icmp_seq=1 Destination Host Unreachable From 192.168.1.102 icmp_seq=1 Destination Host Unreachable ping: sendmsg: Operation not permitted From 192.168.1.102 icmp_seq=1 Destination Host Unreachable ping: sendmsg: Operation not permitted ctrl-c I read somewhere that this may be caused by iptables or other restrictions imposed on the network, but I did not intentionally set anything since it was working yesterday. Again, I'd be content to blow away much of the settings. With static configuration, after bringing the card up I get the message "SIOCADDRT: Network is unreachable" and when I try to ping the host I get "connect: Network is unreachable" just once this time. I have this computer with a floppy drive or if I need to download serious packages, my fiancee has a dvd/cd burner on her laptop -- in fact maybe I should just download the packages. Your help is much appreciated! Randall
