* lsmod > outfile.txt Ok, how do I get my outfile to a floppy?
* You say you can ping outside addresses? and dns works to? such as * ping www.google.com Yup. I can ping without a problem! Ping www.google.com resolves the IP and gets replies in around 200ms. * what is output from wget or apt-get ? wget www.google.com http://www.google.com => 'index.html' Resolving (bunch of IPs bound to the domain) Connecting www.google.com[66.233.16199]:80... Failed: Connection Timed Out apt-get resolves the IP of the server (I am using the University of Berkley server) and then gives some error that the server could not be contacted. Tyson Varosyan Technical Manager, Uptime Technical Solutions LLC. [EMAIL PROTECTED] www.up-times.com 206-715-TECH (8324) UpTime/OnTime/AnyTime -----Original Message----- From: Andrew Sackville-West [mailto:[EMAIL PROTECTED] Sent: Friday, January 06, 2006 2:51 PM To: debian-user@lists.debian.org Subject: Re: TCP not working over ppp connection (WAS: 5th day using Linux...) On Fri, 6 Jan 2006 13:56:10 -0800 "Tyson Varosyan" <[EMAIL PROTECTED]> wrote: > kernel version: uname -a > Linux debian 2.6.8-2-386 #1 Tue Aug 16 12:46:35 UTS 2005 i686 GNU/Linux > > installed modules: lsmod > This gives me a long list of modules. I do not see anything that looks to be > related with ppp, network or tcp. How do I get outputs of these commands to > be dumped to a txt file on a floppy disk? easy, type you're command like this: lsmod > outfile.txt that tells the shell to redirect stdout (standard output) to the file outfile.txt. > > network status: ifconfig > I have listed an Eth0, which does not work. For some reason the 2.6 kernel, > after the initial install, sees my NIC as Eth1. I have not configured Eth1 > yet because I want to focus on this problem. But Eth0 is listed with a very > long hardware address, no IP information and no traffic. > > I have lo assigned to 127.0.0.1 mask 255.0.0.0 No traffic there ether. > > I have ppp0 listed with a valid IP address (I can ping it from the > outside), Link encap:Point-to-Point Protocol Inet addr:70.218.54.229 P-t-P > 66.174.26.4 Mask 255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICASE > MTU:0 Metric:1 > Rxpackets:34 errors:0 dropped:0 overruns:0 frame:0 > Txpackets:52 errors:0 dropped:0 overruns:0 carrier:0 Collosions:0 > txqueuelen:3 RX bytes:3687 (3.6 KiB) TX bytes:3845 (3.7 KiB) > > netfilter config: iptables -L > ip_tables: 2000-2002 Netfilter Core Team > > Chain INPUT (policy ACCEPT) > Target prot opt source destination > > Chain FORWARD (policy ACCEPT) > Target prot opt source destination > > Chain OUTPUT (policy ACCEPT) > Target prot opt source destination > > > Ok this last command looks like a network filter output. Should there not be > more information there? not if you have no filtering setup. I think that's right. okay, so use that command above to send us the output of lsmod and ifconfig. also you might include dmesg | grep eth[01] > outfile.txt as that might have some info as to why you have eth 0 and 1. You say you can ping outside addresses? and dns works to? such as ping www.google.com works for you? what is output from wget or apt-get ? A > > > Tyson Varosyan > Technical Manager, Uptime Technical Solutions LLC. > [EMAIL PROTECTED] > www.up-times.com > 206-715-TECH (8324) > > UpTime/OnTime/AnyTime > > -----Original Message----- > From: Marty [mailto:[EMAIL PROTECTED] > Sent: Friday, January 06, 2006 12:43 PM > To: debian-user@lists.debian.org > Cc: debian-user@lists.debian.org > Subject: Re: TCP not working over ppp connection (WAS: 5th day using > Linux...) > > Tyson Varosyan wrote: > > Hi Marty, > > > > I an very new to Linux. What do I type in to give you more information. I > > used the 180MB install disk image from debian.org and I type in "linux26" > at > > the install prompt... > > Here are some tools that may yield useful output: > > kernel version: uname -a > pci devices: lspci > installed modules: lsmod > network status: ifconfig > netfilter config: iptables -L > > The output of tcpdump and any relevant contents of the system log files, > e.g. > /var/log/messages > > If you're not sure about the relevance of any particular output date, > include > it anyway. More is better. > > I usually include such output in the text of my messages. Other posters > include > output files as attachments or put them on their web site. (The last method > is > probably not the best in terms of archival value.) > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact > [EMAIL PROTECTED] > > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
