On 12/23/05, Mike McCarty <[EMAIL PROTECTED]> wrote:
> Tatsuya Kobayashi wrote:
> > Thank you for reply me!
> >
> >
> >>On Thu, 22 Dec 2005 21:50:07 -0600
> >>Tatsuya Kobayashi <[EMAIL PROTECTED]> wrote:
> >
> >
> >>>Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
> >>> Vendor: eM Model: Bay Reader Rev: 1.01
> >>> Type: Direct-Access ANSI SCSI revision: 02
> >>>Attached scsi removable disk sdb at scsi0, channel 0, id 0, lun 1
> >>> Vendor: eM Model: Bay Reader Rev: 1.02
> >>> Type: Direct-Access ANSI SCSI revision: 02
> >>>Attached scsi removable disk sdc at scsi0, channel 0, id 0, lun 2
> >>> Vendor: eM Model: Bay Reader Rev: 1.03
> >>> Type: Direct-Access ANSI SCSI revision: 02
> >>>Attached scsi removable disk sdd at scsi0, channel 0, id 0, lun 3
> >>>USB Mass Storage device found at 2
> >
> >
> >>Did you try /dev/sdc ?
>
> Umm, doesn't the above indicate that a device was found at *sdd*.
> Does that mean one should mount /dev/sdd?
>
I have tried to access with /dev/sdd and /dev/sdd1 but I couldn't
access. When I could access to this USB flash drive on the kernel 2.4,
I saw on the /dev/sde and partition was /dev/sde1.
Actually, that log was taken when USB drive was connected during boot
process. The log I posted below is taken when I rebooted without USB
drive.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB (ICH4) USB UHCI #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 169, io base 0000e800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB (ICH4) USB UHCI #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 177, io base 0000e880
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB (ICH4) USB UHCI #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 185, io base 0000ec00
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-2: new full speed USB device using address 2
usb 3-1: new low speed USB device using address 2
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: eM Model: Bay Reader Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Vendor: eM Model: Bay Reader Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdb at scsi0, channel 0, id 0, lun 1
Vendor: eM Model: Bay Reader Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi0, channel 0, id 0, lun 2
Vendor: eM Model: Bay Reader Rev: 1.03
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdd at scsi0, channel 0, id 0, lun 3
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
> > I tried to mount /dev/sdc but I couldn't mount it. It's still saying
> > "No medium found" or "special device /dev/sdc1 does not exist."
> > Well what else can I do to mount USB flash drive? Will the kernel
recompile
> > help to fix this problem? I know that my USB drive works on the
kernel 2.4
> > so I think I might be able to go back to kernel 2.4, but can't I
really use
> > my USB flash drive on kernel 2.6?
>
> I had a similar problem with an external USB drive I used to use
> (Fedora Core 2). Sometimes it was detected as /dev/sda and sometimes
> as /dev/sde, so I had two entries in my fstab, one for /dev/sda1 and
> one for /dev/sde1.
>
> Mike
> --
> p="p=%c%s%c;main(){printf(p,34,p,34);}";main(){printf(p,34,p,34);}
> This message made from 100% recycled bits.
> You have found the bank of Larn.
> I can explain it for you, but I can't understand it for you.
> I speak only for myself, and I am unanimous in that!
>
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
