Here's the results I get from smartctl:
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 60 family
Device Model: Maxtor 5T040H4
Serial Number: T4H6CN8C
Firmware Version: TAH71DP0
User Capacity: 40,000,000,000 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0
Local Time is: Mon Nov 14 10:25:04 2005 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection
activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed without error or no
self-test has ever
been run.
Total time to complete Offline
data collection: ( 30) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline
immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test
supported.
No Selective Self-test
supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging
support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 25) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000a 253 252 000 Old_age
Always - 34
3 Spin_Up_Time 0x0027 206 204 063 Pre-fail
Always - 9622
4 Start_Stop_Count 0x0032 252 252 000 Old_age
Always - 2401
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail
Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail
Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
8 Seek_Time_Performance 0x0027 253 248 187 Pre-fail
Always - 51615
9 Power_On_Minutes 0x0032 243 243 000 Old_age
Always - 529h+32m
10 Spin_Retry_Count 0x002b 253 252 223 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 247 247 000 Old_age
Always - 2409
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age
Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age
Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age
Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
201 Soft_Read_Error_Rate 0x000a 253 248 000 Old_age
Always - 154
202 TA_Increase_Count 0x000a 253 252 000 Old_age
Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail
Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age
Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age
Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age
Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age
Always - 0
209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age
Offline - 0
96 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
97 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
98 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
SMART Error Log Version: 1
ATA Error Count: 44510 (device log contains only the most recent five
errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 44510 occurred at disk power-on lifetime: 3568 hours (148 days +
16 hours) When the command that caused the error occurred, the device
was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 ef 67 b3 e4 Error: IDNF at LBA = 0x04b367ef = 78866415
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
30 00 02 ef 67 b3 e4 08 00:05:04.256 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.240 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.224 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.208 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
Error 44509 occurred at disk power-on lifetime: 3568 hours (148 days +
16 hours) When the command that caused the error occurred, the device
was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 ef 67 b3 e4 Error: IDNF at LBA = 0x04b367ef = 78866415
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
30 00 02 ef 67 b3 e4 08 00:05:04.240 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.224 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.208 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
Error 44508 occurred at disk power-on lifetime: 3568 hours (148 days +
16 hours) When the command that caused the error occurred, the device
was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 ef 67 b3 e4 Error: IDNF at LBA = 0x04b367ef = 78866415
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
30 00 02 ef 67 b3 e4 08 00:05:04.224 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.208 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.176 WRITE SECTOR(S)
Error 44507 occurred at disk power-on lifetime: 3568 hours (148 days +
16 hours) When the command that caused the error occurred, the device
was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 ef 67 b3 e4 Error: IDNF at LBA = 0x04b367ef = 78866415
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
30 00 02 ef 67 b3 e4 08 00:05:04.208 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.176 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.160 WRITE SECTOR(S)
Error 44506 occurred at disk power-on lifetime: 3568 hours (148 days +
16 hours) When the command that caused the error occurred, the device
was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 ef 67 b3 e4 Error: IDNF at LBA = 0x04b367ef = 78866415
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.192 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.176 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.160 WRITE SECTOR(S)
30 00 02 ef 67 b3 e4 08 00:05:04.144 WRITE SECTOR(S)
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
Steve
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
