Arsalan, please "Reply-All" when using the list so others may share in
the results (this assumes that we have useful results ;)
You must have an entry for eth1 in /etc/network/interfaces for it to be
activated.
man interfaces
is a good starting point. The entry will depend on what you are doing
with that interface. That is, is it a fixed ip or using dhcp? do you
want it to start automatically? or manually? etc etc etc.
good luck.
A
Arsalan Lodhi wrote:
i guess not -- htis is what i've
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet dhcp
what should i add in ?
Best,
AL
On 9/7/05, *Andrew Sackville-West* <[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>> wrote:
do you have eth1 listed in /etc/network/interfaces?
A
Arsalan Lodhi wrote:
> Hello -
>
> for ease: relevant important text is bold and italic - simply
put, i am
> not sure what should i check next now ?
>
> problem is that once i execute "ifconfig" - i still get etho and lo
> .. but no information about eth1 -
>
> i started finding the type of my Ethernet card which is => 3COM905B,
> then I found to load its dirver as module for which i executed insmod
> 3c59x - but it tells me that the driver already installed - at this
> point i've no clue what should be my next step to enable my second
> ethernet card and to get IP on that -
>
> excerpt from *dmesg | more *
> **
> PCI: Found IRQ 11 for device 00:11.0
> PCI: Sharing IRQ 11 with 00:07.2
> 3c59x: Donald Becker and others.
> www.scyld.com/network/vortex.html
<http://www.scyld.com/network/vortex.html>
<http://www.scyld.com/network/vortex.html>
> See Documentation/networking/vortex.txt
> */00:11.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xcc00.
> /*Vers LK1.1.18-ac
> 00:c0:4f:53:95:b3, IRQ 11
> product code 4920 rev 00.9 date 07-03-97
> Internal config register is 1800000, transceivers 0xa.
> 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate
interface.
> MII transceiver found at address 24, status 786d.
> Enabling bus-master transmits and whole-frame receives.
> 00:11.0 : scatter/gather enabled. h/w checksums enabled
> PCI: Found IRQ 9 for device 02:09.0
> PCI: Sharing IRQ 9 with 01:00.0
> See Documentation/networking/vortex.txt
> */02:09.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xdc80./
> *Vers LK1.1.18-ac
> 00:04:76:c9:fd:41, IRQ 9
> product code 4d4c rev 00.12 date 09-17-01
> Internal config register is 1800000, transceivers
> 0xa.
> 8K byte-wide RAM 5:3 Rx:Tx split,
> autoselect/Autonegotiate interface.
> MII transceiver found at address 24, status 786d.
> Enabling bus-master transmits and whole-frame
> receives.
>
--------------------------------------------------------------------------------------------------------------------------------------------
>
> someone asked me to always paste lspci to the list for that matter:
>
> lspci
>
> 0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX
Host
> bridge (rev 03)
> 0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP
> bridge (rev 03)
> 0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
> 0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE
(rev 01)
> 0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB
(rev 01)
> 0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
> 0000:00:0d.0 Multimedia audio controller: Aureal Semiconductor
Vortex 1
> (rev 02)
> 0000:00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152
> (rev 03)
> */0000:00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX
> [Cyclone] (rev 24) /*
> 0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D
Rage Pro
> AGP 1X/2X (rev 5c)
> /*0000:02:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX
> [Cyclone] (rev 30)*
> /
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
