-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 A long time ago, in a galaxy far, far way, someone said...
> It is a v4. Here is the output of cat /proc/pci: > > PCI devices found: > Bus 0, device 0, function 0: > Non-VGA device: Compaq Unknown device (rev 1). > Vendor id=e11. Device id=1000. > Medium devsel. IRQ 32. Master Capable. Latency=32. Min Gnt=35. > Non-prefetchable 32 bit memory at 0x4198f0 [0x4198f0]. > Non-prefetchable 32 bit memory at 0x3127d0 [0x3127d0]. > Non-prefetchable 32 bit memory at 0x4198f0 [0x4198f0]. > Non-prefetchable 32 bit memory at 0x5ff4160 [0x5ff4160]. > I/O at 0x10000e10 [0x10000e11]. > I/O at 0xe3000144 [0xe3000147]. > Bus 0, device 10, function 0: > VGA compatible controller: Cirrus Logic GD 5434 (rev 142). > Fast devsel. IRQ 10. > Non-prefetchable 32 bit memory at 0x40000000 [0x40000000]. > Bus 0, device 14, function 0: > Ethernet controller: Unknown vendor Unknown device (rev 17). > Vendor id=1317. Device id=985. > Medium devsel. Fast back-to-back capable. IRQ 11. Master Capable. > Latency=66. Min Gnt=255.Max Lat=255. > I/O at 0x1000 [0x1001]. > Non-pre Non-prefetchable 32 bit memory at 0x41000000 [0x41000000]. > Bus 0, device 15, function 0: > ISA bridge: Compaq Unknown device (rev 67). > Vendor id=e11. Device id=2. > Medium devsel. Master Capable. No bursts. > > How does this output look to you? I have no idea what that first 'unknown' > device is? No idea. That can be worried about later once Linux installed. > What are your thoughts? Two thoughts: My first thought is: you're stuck, I have to say. Your ethernet card is new enough to be unsupported by the Debian install procedure. For various reasons binary-only drivers don't necessarily work too well with Linux, which is why Linksys distributed them only in source form. That leads me to my second thought: someone can provide you with the drivers. I have them compiled for the kernel on the boot disks, and they work for me in my limited testing. I make no guarantees that they will work for anyone but me. Hell, I haven't even *tried* this procedure before - I made the drivers on a system that I already had Debian installed on, and I don't have any way of trying out this procedure at the moment. The drivers are at: http://tux.creighton.edu/~pbrutsch/drivers.zip. The The archive (in PKZip format) needs to be extracted to a MS-DOS formatted floppy. Start the installation procedure like normal. When it comes time to load the device driver modules, switch to the command prompt. Then: 1) put the floppy with the driver files in the disk drive 2) do "mount -t vfat /dev/fd0 /mnt" 3) do "cp /mnt/pci-scan.o /target/lib/modules/2.2.17/net/" 4) do "cp /mnt/tulip.o /target/lib/modules/2.2.17/net/" 5) do "umount /mnt" 6) pop the floppy out of the drive Switch back to the installation menu. You should be able to load the tulip driver without problems. PS: In case anyone is interested the source files themselves are at: http://tux.creighton.edu/~pbrutsch/netdrivers.tgz - -- - ---------------------------------------------------------------------- Phil Brutsche [EMAIL PROTECTED] GPG fingerprint: 9BF9 D84C 37D0 4FA7 1F2D 7E5E FD94 D264 50DE 1CFC GPG key id: 50DE1CFC GPG public key: http://tux.creighton.edu/~pbrutsch/gpg-public-key.asc -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.0.1 (GNU/Linux) Comment: For info see http://www.gnupg.org iD8DBQE55SlX/ZTSZFDeHPwRAiwSAJ0e0uhQDnO9YC7QZaD3eUw7i3DtxwCgjcSU 51Ev1BXIjz6NMmyobdEPq/s= =DliD -----END PGP SIGNATURE-----
