I have this line in my /etc/modutils/arch/i386
options sb io=0x220 irq=5 dma=1 dma16=5 mpu_io=0x330
Try putting this in and running update-modules. May require a reboot for isapnp
to load again :-\
NOTE: That line matches my settings in /etc/isapnp.conf so you /may/ have to
change a couple of those settings. I just took a look at when your isapnp loads
and I don't think you should have to change anything.
A side note - I had this exact same config pretty much and it was working great
in a base install of potato. However, one day - I like living on the edge - my
modutils got upgraded and since then, all I get is /dev/dsp: Device or resource
busy. I don't know what happened. :-( However, the above should still work for
you - and perhaps I just did something stupid when I upgraded my modutils, I
don't know.
I also have sb in my /etc/modules
Good luck!
isetr0
On Mon, Sep 25, 2000 at 09:55:32AM -0400, Brian J. Dumont wrote:
> Hi,
>
> I have a PII-333 machine with a Soundblaster Awe64 Gold installed. I had
> been running Redhat 6.1 for a couple years with the soundcard functioning
> properly (so I think the hardware is OK). I recently wiped the drive and
> have installed Debian 2.2 instead, but I cannot seem to get the soundcard
> to run. I am using Debian's default 2.2.17 kernel.
>
>
> I have looked through the kernel config to verify:
> CONFIG_SOUND_SB=m
> CONFIG_SOUND=m
> CONFIG_LOWLEVEL_SOUND=y
> CONFIG_AWE32_SYNTH=m
>
>
> I have set up isapnp to work properly, giving these results:
>
> Board 1 has Identity f1 05 78 ee 7e b2 00 8c 0e: CTL00b2 Serial No 91811454
> [checksum f1]
> CTL00b2/91811454[0]{Audio }: Ports 0x220 0x330 0x388; IRQ5 DMA1
> DMA5 --- Enabled OK
> CTL00b2/91811454[1]{Game }: Port 0x200; --- Enabled OK
> CTL00b2/91811454[2]{WaveTable }: Port 0x640; --- Enabled OK
>
> either at boot time or if I run isapnp from the shell.
>
>
> I have also appended the line:
> sound
> to my /etc/modules file. After boot, I can run lsmod and see the
> soundcore, soundlow, and sound modules, but if I cat /dev/sndstat
> I see:
>
> OSS/Free:3.8s2++-971130
> Load type: Driver loaded as a module
> Kernel: Linux tim 2.2.17 #1 Sun Jun 25 09:24:41 EST 2000 i686
> Config options: 0
>
> Installed drivers:
>
> Card config:
>
> Audio devices:
>
> Synth devices:
>
> Midi devices:
>
> Timers:
> 0: System clock
>
> Mixers:
>
>
> I can also find:
> 14 sound
> in my /proc/devices
>
>
> I then tried modprobe -a sb from my /lib/modules/2.2.17/misc
> directory. At this point, my /dev/sndstat looks like:
>
>
> OSS/Free:3.8s2++-971130
> Load type: Driver loaded as a module
> Kernel: Linux tim 2.2.17 #1 Sun Jun 25 09:24:41 EST 2000 i686
> Config options: 0
>
> Installed drivers:
>
> Card config:
>
> Audio devices:
> 0: Sound Blaster 16 (4.16) (DUPLEX)
>
> Synth devices:
>
> Midi devices:
> 0: Sound Blaster 16
>
> Timers:
> 0: System clock
>
> Mixers:
> 0: Sound Blaster
>
>
> with an lsmod of:
> Module Size Used by
> sb 33396 0 (unused)
> uart401 6128 0 [sb]
> sound 57592 0 [sb uart401]
> soundlow 416 0 [sound]
> soundcore 2628 6 [sb sound]
> lockd 31112 1 (autoclean)
> sunrpc 52420 1 (autoclean) [lockd]
> unix 10212 96 (autoclean)
>
>
> which looks like it worked; but when I play a sound, I get every
> other bit of the sound. In other words, it plays for about 1/2 second,
> then is silent for about 1/2 second, then plays for 1/2 second, and so on.
>
> It sounds to me like an IRQ conflict, but the only other ISA device
> that's in the machine is a modem on ttyS1 IRQ3 (not PnP, set by jumpers);
> and it doesn't seem like that should be the case anyway, since I haven't
> switched any jumpers since I had Red Hat.
>
> I can't seem to figure out what I'm missing. Any ideas?
> Thanks very much,
> Brian
>
> -------------------------------------------------------------------------------
> Brian J. Dumont - [EMAIL PROTECTED]
>
>
> --
> Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED] < /dev/null
>
>
