The CD-Writing-HOWTO helped me out alot. Snippet from http://www.ibiblio.org/pub/Linux/docs/HOWTO/other-formats/html_single/CD-Wri ting-HOWTO.html
Sect. Description Module SCSI IDE PP ------------------------------------------------------------ BLOCK Enhanced IDE/MFM/RLL... Y BLOCK IDE/ATAPI CDROM ide-cd M BLOCK SCSI emulation support ide-scsi M BLOCK Loopback device loop M M M SCSI SCSI support scsi_mod Y/M Y/M SCSI SCSI CD-ROM support sr_mod Y/M Y/M SCSI Enable vendor-specific Y Y SCSI SCSI generic support sg Y/M Y/M SCSI (select a low-level driver) Y FS ISO 9660 CDROM filesystem iso9660 Y/M Y/M Y/M FS Microsoft Joliet cdrom... joliet Y Y Y Also check /usr/src/linux/.config and make sure: CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDESCSI=y -- for some reason mine wasn't set. also make sure you have append="hdc=ide-scsi" --assuming you're CD-Writer in the master on the secondary IDE controller Hope this helps. --jim -----Original Message----- From: Marcelo Chiapparini [mailto:[EMAIL PROTECTED]] Sent: Wednesday, January 22, 2003 9:06 AM To: debian user Subject: Cannot open SCSI driver Hello! I am running woody and I have a cdrom and a cdwriter. I want to write cds using the cdwriter reading from the cdrom. Both are ATAPI devices, so I have compiled the kernel, 2.4.18, with the following options: a) scsi generic support enabled b) scsi cdrom support enabled c) ATAPI cdrom support disabled At boot time, the scsi support is started as we can see from the dmesg output: hda: ST320413A, ATA DISK drive hdc: CREATIVE CD5233E, ATAPI CD/DVD-ROM drive hdd: Hewlett-Packard CD-Writer Plus 9500b, ATAPI CD/DVD-ROM drive SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: CREATIVE Model: CD5233E Rev: 2.02 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 9500b Rev: 1.06 Type: CD-ROM ANSI SCSI revision: 02 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0 sr0: scsi3-mmc drive: 8x/56x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 sr1: scsi3-mmc drive: 31x/32x writer cd/rw xa/form2 cdda tray So, I have the following scsi map: adapter device channel id lun CD5233E CD-ROM scsi0 sr0 0 0 0 HP CD-Writer scsi0 sr1 0 1 0 In the lilo.conf file I have the line append = "hdc=ide-scsi hdd=ide-scsi max_scsi_luns=1" Apparently everything works fine, I can listen music with the cdrom and edit and copy files from the cdrom and cdwriter to the hd. But when I run cdrecord with the -scanbus option I get the message: nostromo:/home/chiappa# cdrecord -scanbus Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling cdrecord: No such file or directory. Cannot open SCSI driver. thus, cdrecord cannot find the SCSI driver (scsi0?). But the scsi drive is readed during the boot process, as can be seen from the dmesg output above. What is going wrong? Any help will be very appreciated! Marcelo -- Marcelo Chiapparini DFT-IF/UERJ [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
