well as i said winblows worked perfectly so hardware? dont think so
i even tried turning off pci_retry which should remove noise under
Xwindows but no positive result
On 28 Oct, Leszek Gerwatowski wrote:
> On Thu, Oct 28, 1999 at 09:54:02AM +0200, Rune Linding Raun wrote:
>> a lsmod here gives:
>>
>> opl3sa2 3400 1
>> ad1848 15060 1 [opl3sa2]
>> mpu401 17676 1 [opl3sa2]
>>
>> and in conf.modules:
>>
>> options opl3sa2 io=0x100 io=0x201 io=0x220 mss_io=0x530 mpu_io=0x370
>> irq=5 dma=0 dma2=1
>>
>
> I prefer ALSA driver. Here is my /etc/conf.modules configuration:
>
> alias char-major-116 snd
> options snd snd_major=116 snd_cards_limit=1
> alias snd-card-0 snd-card-opl3sa2
> options snd-card-opl3sa2 snd_port=0x240 snd_wss_port=0xe80
> snd_midi_port=0x300 snd_fm_port=0x388 snd_irq=10 snd_dma1=1 snd_dma1_size=64
> snd_dma2=3 snd_dma2_size=64 snd_isapnp=1 snd_id=YMF-719
>
> # OSS/Free setup
> alias char-major-14 soundcore
> alias sound-slot-0 snd-card-0
> alias sound-service-0-0 snd-mixer-oss
> alias sound-service-0-1 snd-seq-oss
> alias sound-service-0-3 snd-pcm1-oss
> alias sound-service-0-12 snd-pcm1-oss
>
> And my lsmod:
>
> snd-mixer-oss 3592 0 (autoclean)
> snd-pcm1-oss 12788 1 (autoclean)
> snd-card-opl3sa2 8712 1
> isapnp 23169 0 [snd-card-opl3sa2]
> snd-cs4231 15864 0 [snd-card-opl3sa2]
> snd-mixer 25824 0 [snd-mixer-oss snd-card-opl3sa2
> snd-cs4231]
> snd-pcm1 16500 0 [snd-pcm1-oss snd-cs4231]
> snd-opl3 1956 0 [snd-card-opl3sa2]
> snd-timer 7500 0 [snd-cs4231 snd-pcm1 snd-opl3]
> snd-hwdep 2484 0 [snd-card-opl3sa2 snd-opl3]
> snd-pcm 8696 0 [snd-pcm1-oss snd-card-opl3sa2
> snd-cs4231 snd-pcm1]
> snd-mpu401-uart 1692 0 [snd-card-opl3sa2]
> snd-midi 12144 0 [snd-card-opl3sa2 snd-mpu401-uart]
> snd 32972 1 [snd-mixer-oss snd-pcm1-oss
> snd-card-opl3sa2
> snd-cs4231 snd-mixer snd-pcm1 snd-opl3
> snd-timer snd-hwdep snd-pcm snd-mpu401-uart
> snd-midi]
> soundcore 2444 4 [snd]
>
> I'm playing now some mp3 files with 44.1kHz (using mpg123) without any
> problems.
>
> I also use normal OSS drivers with such configuration:
>
> alias char-major-14 opl3sa2
> pre-install opl3sa2 modprobe "-k" "ad1848"
> post-install opl3sa2 modprobe "-k" "opl3"
> options opl3sa2 io=0x240 mss_io=0xe80 mpu_io=0x300 irq=10 dma=1 dma2=3
> options opl3 io=0x388
>
> And lsmod:
>
> opl3 10476 1 (autoclean)
> opl3sa2 3644 1
> ad1848 15420 1 [opl3sa2]
> mpu401 17964 1 [opl3sa2]
> sound 55388 0 [opl3 opl3sa2 ad1848 mpu401]
> soundcore 2444 7 [sound]
>
> With this configuration I've sometimes problems (but right now it works OK
> also with 44.1kHz).
>
> Maybe your problems are not configuration-specific but hardware specific
> (I don't like built-in hardware since my strange problems with Matrox G200
> on mainboard)?
>
> Good luck!
>
--
Best Regards :)
Rune Linding Raun
Graduate student,B.Sc.
University of Copenhagen cellphone: +45 2625 6801
Institute of Molecular Biology pager: +45 5020 8680
Department of Biological Chemistry phone(lab): +45 3532 2024
Sølvgade 83H Copenhagen fax(lab): +45 3532 2040
DK-1307 DENMARK
email: [EMAIL PROTECTED]
sms: [EMAIL PROTECTED]
____ _ _ _ _ ______ _ _
/ ___| \ | | | | | / / _ \ ___| |__ (_) __ _ _ __
| | _| \| | | | |/ /| | | |/ _ \ '_ \| |/ _` | '_ \
| |_| | |\ | |_| / / | |_| | __/ |_) | | (_| | | | |
\____|_| \_|\___/_/ |____/ \___|_.__/|_|\__,_|_| |_|
_ ___ _ _ _ ___ __ ____ _
| | |_ _| \ | | | | \ \/ / |___ \ / |
| | | || \| | | | |\ / __) | | |
| |___ | || |\ | |_| |/ \ / __/ _| |
|_____|___|_| \_|\___//_/\_\ |_____(_)_|
