Okay, listen here's the deal: you need to take OUT ide-cd support leave in scsi-emulation, scsi-generic, scsi-cdrom...... now ./MAKDEV sg I'm pretty sure that the /dev/scd* come pre-made the important thing is to see if you get messages like this on bootup: scsi0 : AdvanSys SCSI 3.1E: PCI 20 CDB: IO E400/F, IRQ 9 scsi1 : SCSI host adapter emulation for IDE ATAPI devices scsi : 2 hosts. Vendor: HP Model: C5110A Rev: 3638 Type: Processor ANSI SCSI revision: 02 Detected scsi generic sga at scsi0, channel 0, id 1, lun 0 Vendor: IOMEGA Model: ZIP 100 Rev: 13.A Type: Direct-Access ANSI SCSI revision: 00 Detected scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Vendor: E-IDE Model: CD-ROM 45X/A Rev: 30 Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0 Vendor: PHILIPS Model: CDD3610 CD-R/RW Rev: 3.08 Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0 scsi : detected 2 SCSI cdroms 1 SCSI disk total. sr0: scsi3-mmc drive: 0x/20x xa/form2 cdda tray Uniform CDROM driver Revision: 2.55 sr1: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
this means for cdrecord I do dev=1,2,0 --dave On 9 Sep 1999, Morgan Fletcher wrote: > I'm trying to utilize my IDE CD-R drive (HP CD-Writer 8100) via scsi > emulation to burn discs with cdrecord. I've been reading > http://www.guug.de/~winni/linux/cdr/html/CD-Writing.html#toc1 for the > last couple of days, and have done a few things listed there, but now > I'm stuck. > > Here's my setup: > > x86 > adaptec 2940 > scsi cd-rom > scsi hard disk > ide cd-burner (HP CD-Writer 8100) > debian potato linux > custom 2.2.10 kernel > > I've built a custom kernel with this (abridged) configuration: > > BLOCK Enhanced IDE/MFM/RLL... M > BLOCK IDE/ATAPI CDROM ide-cd M > BLOCK SCSI hostadaptor emulation ide-scsi M > BLOCK Loopback device loop M > SCSI SCSI support scsi_mod Y > SCSI SCSI CD-ROM support sr_mod M > SCSI Enable vendor-specific Y > SCSI SCSI generic support sg M > SCSI (select a low-level driver) aic7xxx Y > FS ISO 9660 CDROM filesystem iso9660 Y > FS Microsoft Joliet cdrom... joliet Y > > I've also added 'append="hda=ide-scsi"' to my /etc/lilo.conf, and also > 'alias scsi_hostadapter ide-scsi' to /etc/modutils/aliases and > 'options ide-cd ignore=hda' to /etc/modutils/modconf, and run > update-modules of course. I've tried variations, for instance with > IDE=Y, etc. > > What device should I use to access the device now that I'm > theoretically using scsi emulation? > > Running 'cdrecord -scanbus' gets me: > > Cdrecord release 1.8a25 Copyright (C) 1995-1999 Jörg Schilling > scsibus0: > 0) 'SEAGATE ' 'ST34371N ' '0338' Disk > 1) 'MATSHITA' 'CD-ROM CR-506 ' '8S05' Removable CD-ROM > 2) * > 3) * > 4) * > 5) * > 6) * > 7) * > > I have no idea what do next! I have no /dev/sr* devices, and can't > seem to make them with /dev/MAKEDEV. What device should I use to > access the HP? How can I load up a module so as to make it show up in > the output of 'cdrecord -scanbus'? > > morgan > > > -- > Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED] < /dev/null > > >
