Hi !
I've been trying to run this soundcard since I first installed Debian
GNU/Linux. I don't know which drivers to use ? Alsa ? These from kernel
(2.0.36) ? Will these from kernel work ? (I don't use 2.2.x and 'll not
use it untill Potato goes stable). I thought that this won't work on
kernel drivers so I tried Alsa and it was like this :
I downloaded :
ii alsa-modules 0.2.0-pre8-3
ii alsa-source 0.2.0-pre8-3
ii alsalib 0.1.1-1
ii alsalib-dev 0.1.1-1
ii alsautils 0.0.6-2
did: make-kpkg --revision 1.0 modules_image, and installed *.deb it made
and run alsaconfig, update-modules and rebooted
So i tried to turn it on by typing:
modprobe snd.o
modprobe snd-opl3sa.o snd_port=0x220 snd_wss_port=0x530
snd_midi_port=0x330 snd_fm_port=0x388 snd_irq=5 snd_dma1=0
snd_dma1_size=16 snd_dma2=1 snd_dma2_size=16
and I got :
snd: Yamaha OPL3-SA soundcard #1 not found at 0x220 or device busy
snd: Yamaha OPL3-SA soundcard not found or device busy
/lib/modules/2.0.36/misc/snd-opl3sa.o: init_module: Device or resource
busy
snd: Device or resource busy
So I thoght that I must use isapnp.
I configured isapnp.conf and when I run isapnp I got
lspci not found, so PCI resource conflict not checked
Board 1 has Identity cb 80 86 00 01 30 00 a8 65: YMH0030 Serial No
2156265473 [checksum cb]
YMH0030/2156265473[0]{OPL3-SA3 Snd System }: Ports 0x220 0x530 0x388 0x330
0x370; IRQ5 DMA0 DMA1 --- Enabled OK
YMH0030/2156265473[1]{OPL3-SA3 Snd System }: --- Enabled OK
and there was nothing ... the same when running modprobe snd[...] :
snd: Yamaha OPL3-SA soundcard #1 not found at 0x220 or device busy
snd: Yamaha OPL3-SA soundcard not found or device busy
/lib/modules/2.0.36/misc/snd-opl3sa.o: init_module: Device or resource
busy
snd: Device or resource busy
******************************
... so what did I do wrong ? Maybe I should use drivers from kernel ?
What can be wrong ?
P.S. I tried to run commercial OSS and it worked, but it only run for 20
minutes :( It did everything automaticlly and it worked. (I didn't even
use isapnp)
I'm attaching /etc/isapnp.conf just in case ...
--
Piotr Domagalski <[EMAIL PROTECTED]>
Linux is like a wigwam - no Windows, no Gates, Apache inside.
# Trying port address 0203
# Board 1 has serial identifier cb 80 86 00 01 30 00 a8 65
# (DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier cb 80 86 00 01 30 00 a8 65)
# Vendor Id YMH0030, Serial Number 2156265473, checksum 0xCB.
# Version 1.0, Vendor version 0.0
# ANSI string -->OPL3-SA3 Snd System<--
#
# Logical device id YMH0021
#
(CONFIGURE YMH0030/2156265473 (LD 0
(IO 0 (SIZE 16) (BASE 0x0220))
(IO 1 (SIZE 8) (BASE 0x0530))
(IO 2 (SIZE 8) (BASE 0x0388))
(IO 3 (SIZE 2) (BASE 0x0330))
(IO 4 (SIZE 2) (BASE 0x0370))
(INT 0 (IRQ 5 (MODE +E)))
(DMA 0 (CHANNEL 0))
(DMA 1 (CHANNEL 1))
# Start dependent functions: priority acceptable
# (IO 0 (SIZE 16) (BASE 0x0240))
# (IO 1 (SIZE 8) (BASE 0x0e80))
# (IO 2 (SIZE 8) (BASE 0x0388))
# (IO 3 (SIZE 2) (BASE 0x0300))
# (IO 4 (SIZE 2) (BASE 0x0100))
# (INT 0 (IRQ 5 (MODE +E)))
# (DMA 0 (CHANNEL 0))
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority functional
# (IO 0 (SIZE 16) (BASE 0x0220))
# (IO 1 (SIZE 8) (BASE 0x0530))
# (IO 2 (SIZE 8) (BASE 0x0388))
# (IO 3 (SIZE 2) (BASE 0x0300))
# (IO 4 (SIZE 2) (BASE 0x0100))
# (INT 0 (IRQ 5 (MODE +E)))
# (DMA 0 (CHANNEL 0))
# (DMA 1 (CHANNEL 3))
(NAME "YMH0030/2156265473[0]{OPL3-SA3 Snd System }")
(ACT Y)
))
#
# Logical device id YMH0022
(CONFIGURE YMH0030/2156265473 (LD 1
# Compatible device id PNPb02f
# Start dependent functions: priority preferred
# (IO 0 (SIZE 1) (BASE 0x0201))
# Start dependent functions: priority acceptable
# (IO 0 (SIZE 1) (BASE 0x0201))
(NAME "YMH0030/2156265473[1]{OPL3-SA3 Snd System }")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
