Nils Rennebarth wrote: > On Wed, Apr 01, 1998 at 09:10:16PM +0000, Jeffery D. Collins wrote: > > > > Here is lilo.conf: > > > > > > > > > > > > $ cat /etc/lilo.conf > > > > boot=/dev/hda1 > > > > root=/dev/hda1 > > > > compact > > > > install=/boot/boot.b > > > > map=/boot/map > > > > vga=normal > > > > delay=20 > > > > image=/vmlinuz > > > > label=Linux > > > > read-only > > > > > try to remove compact and add the option linear. > > I just tried this, but it still hung on "LI". > Is this disk larger than 504 MB? > > That means you need either LBA or LARGE in the BIOS settings. If this is > not possible your BIOS can't see the whole disk and you either need a BIOS > upgrade or repartition and make a partition fully below the 504 MB limit. > All of LILO should live there, i.e. make this your root partition.
The disk is approx 250Meg, part of an old 486DX-33 system. This debianinstall actually replaces an older Redhat installation. During the install, I reformatted the partitions (approx 16 meg for swap, the remaining for root) and installed in the usual way. During the reboot process, everything went fine until the configuring of the serial ports (probably while executing code in the /etc/rc.boot/0setserial). The remaining portion of the boot obviously failed and though a login prompt appeared, a tty could not be found for actually logging in. I didn't know what the problem could be, so I rebuilt the kernel, installed it and ran lilo. (Note that the boot floppy created during the original install process continues to work fine.) It was then that the problem of the booting process halting at "LI" began. This problem now persists, even after switching back to the original kernel. It is for this reason that I suggested the possiblity of corrupted files, such as boot.b. So, though I could work around the problem using a boot floppy, I know that it should be bootable from the hard disk without extraordinary reconfiguring of lilo. Ultimately, that may mean reformating and reinstalling:( For fun, here are the partitions: -------------- bootable hard disk ------------------- Disk /dev/hda: 16 heads, 31 sectors, 967 cylinders Units = cylinders of 496 * 512 bytes Device Boot Begin Start End Blocks Id System /dev/hda1 * 1 1 900 223184+ 83 Linux native /dev/hda2 901 901 967 16616 82 Linux swap ---------------- second hard disk (data only)---------- Disk /dev/hdb: 8 heads, 39 sectors, 762 cylinders Units = cylinders of 312 * 512 bytes Device Boot Begin Start End Blocks Id System /dev/hdb1 * 1 1 761 118696+ 83 Linux native ----------------------------------------------- > > > What are the BIOS settings for this hd? You need to partition it with the > same settings as those you use it thereafter. If repartioning is an option > try this. > I'll have to check this tomorrow. > > Perhaps I should also specify > > thedisk geometry in the lilo.conf file as well. > This might help if you use the LARGE setting. > > > I wonder if the boot.b got corrupted somehow? > Not very probable. > > Nils > > -- > *-----------------------------------------------------------------------------* > | Quotes from the net: L> Linus Torvalds, W> Winfried Truemper > | > | L>this is the special easter release of linux, more mundanely called 1.3.84 > | > | W>Umh, oh. What do you mean by "special easter release"?. Will it quit > | > * W>working today and rise on easter? > * > > ------------------------------------------------------------------------ > > Part 1.2 Type: application/pgp-signature -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
