ide cdrw usb modules nat and gis

[Philip Mark Donaghy]

I am happy to say that my debian experience is going really well. I have created a internal network using NAT and have installed and configured a gis mapping website using MapServer. Apart from that my imediate goals are to configure a scanner and the cdrw drive.

apropo cdrw syslog says :

Nov 13 11:32:00 france kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Nov 13 11:32:00 france kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 13 11:32:00 france kernel: ALI15X3: IDE controller on PCI bus 00 dev 78
Nov 13 11:32:00 france kernel: PCI: No IRQ known for interrupt pin A of device 00:0f.0. Please try using pci=biosirq.
Nov 13 11:32:00 france kernel: ALI15X3: chipset revision 193
Nov 13 11:32:00 france kernel: ALI15X3: not 100%% native mode: will probe irqs later
Nov 13 11:32:00 france kernel: ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:pio
Nov 13 11:32:00 france kernel: ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio
Nov 13 11:32:00 france kernel: hda: ST33221A, ATA DISK drive
Nov 13 11:32:00 france kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 13 11:32:00 france kernel: hdc: CR-4804TE, ATAPI CD/DVD-ROM drive
Nov 13 11:32:00 france kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Nov 13 11:32:00 france kernel: ide1 at 0x170-0x177,0x376 on irq 15

apropo cdrw /var/log/messages says :

Nov 13 11:51:58 france -- MARK --
Nov 13 11:59:52 france kernel: SCSI subsystem driver Revision: 1.00
Nov 13 12:04:52 france kernel: hdc: ATAPI 24X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Nov 13 12:04:52 france kernel: Uniform CD-ROM driver Revision: 3.12
Nov 13 12:31:58 france -- MARK --

lsmod reports :

france:/var/log# lsmod
Module Size Used by Not tainted
nls_iso8859-1 2880 0 (autoclean)
ide-cd 26048 0 (autoclean)
cdrom 27072 0 (autoclean) [ide-cd]
isofs 24064 0 (autoclean)
sg 27940 0 (autoclean) (unused)
scsi_mod 84792 1 (autoclean) [sg]
smbfs 31136 1 (autoclean)
ipt_REJECT 2784 1 (autoclean)
ipt_MASQUERADE 1216 1 (autoclean)
ipt_state 608 4 (autoclean)
iptable_mangle 2112 0 (autoclean) (unused)
iptable_nat 12820 1 (autoclean) [ipt_MASQUERADE]
ip_conntrack 12780 2 (autoclean) [ipt_MASQUERADE ipt_state iptable_nat]
iptable_filter 1728 1 (autoclean)
ip_tables 10368 8 [ipt_REJECT ipt_MASQUERADE ipt_state iptable_mangle iptable_nat iptable_filter]
8139too 13504 3
mii 1056 0 [8139too]
af_packet 11464 1
rtc 5368 0 (autoclean)
unix 13316 10 (autoclean)
ide-disk 6560 3 (autoclean)
ide-probe-mod 7968 0 (autoclean)
ide-mod 129036 3 (autoclean) [ide-cd ide-disk ide-probe-mod]
ext2 30304 2 (autoclean)
ext3 56224 0 (autoclean)
jbd 34840 0 (autoclean) [ext3]

Unfortunately nothing is comming up about the USB ports.

I installed sane_1.0.7-2.1_i386.deb and cdrecord_1.10-7_i386.deb today. The output of cdrecord -scanbus is obvious, IDE is not supported.

france:/var/log# cdrecord -scanbus
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
cdrecord: No such file or directory. Cannot open SCSI driver.
cdrecord: For possible targets try 'cdrecord -scanbus'. Make sure you are root.

The scanner is not detected either.

france:/var/log# sane-find-scanner /dev/usb/scanner0 and
france:/var/log# sane-find-scanner /dev/usb/scanner1 both return
# Note that sane-find-scanner will find any scanner that is connected
# to a SCSI bus and some scanners that are connected to the Universal
# Serial Bus (USB) depending on your OS. It will even find scanners
# that are not supported at all by SANE. It won't find a scanner that
# is connected to a parallel or proprietary port.

# If your scanner uses SCSI, you must have a driver for your SCSI
# adapter and support for SCSI Generic (sg) in your Operating System
# in order for the scanner to be used with SANE. If your scanner is
# NOT listed above, check that you have installed the drivers.

Can anyone tell me how I can test/debug these devices?

The scanner is a Agfa SnapScan e52

Thanks.

--
Philip Mark Donaghy
Developer and Architect Java 2 Platform
Ingénieur Développement et Architecture Plateforme Java 2
Mobile : +33 (0)6 20 83 22 62
Direct : +33 (0)1 48 74 23 80
Website : http://www.mapimage.com/



--
To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]