Thanks for the tip, I tried 2.6.23-rc3 but it's still the same - with
ACPI I get no DVD device detected, without ACPI it works. I'm attaching
the output from dmesg and lspci both with and without acpi=off.
I have also tried the kernel options suggested in the dmesg output
(acpi_apic_instance=2 and acpi_osi=Linux), first the one then the other
then both, but it didn't do any difference.
Any tips on where to look for solutions would be very much appreciated!
Linux version 2.6.23-rc3-amd64 (Debian
2.6.23~rc3-1~experimental.1~snapshot.9384) ([EMAIL PROTECTED]) (gcc version
4.1.3 20070718 (prerelease) (Debian 4.1.2-14+1)) #1 SMP Mon Aug 27 23:59:33 UTC
2007
Command line: root=/dev/sda1 ro
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f670000 (usable)
BIOS-e820: 000000007f670000 - 000000007f680000 (ACPI NVS)
BIOS-e820: 000000007f680000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 521840) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F7510, 0024 (r2 PTLTD )
ACPI: XSDT 7F676F78, 0094 (r1 PTLTD XSDT 6040000 LTP 0)
ACPI: FACP 7F67ECDD, 00F4 (r3 INTEL CRESTLNE 6040000 ALAN 1)
ACPI: DSDT 7F678CFF, 5F6A (r2 INTEL CRESTLNE 6040000 INTL 20050624)
ACPI: FACS 7F67FFC0, 0040
ACPI: APIC 7F67EDD1, 0068 (r1 INTEL CRESTLNE 6040000 LOHR 5A)
ACPI: HPET 7F67EE39, 0038 (r1 INTEL CRESTLNE 6040000 LOHR 5A)
ACPI: MCFG 7F67EE71, 003C (r1 INTEL CRESTLNE 6040000 LOHR 5A)
ACPI: TCPA 7F67EEAD, 0032 (r1 Intel CRESTLN 6040000 5A52)
ACPI: TMOR 7F67EEDF, 0026 (r1 PTLTD 6040000 PTL 3)
ACPI: ASF! 7F67EF05, 006B (r32 OEMID OEMTBL 6040000 PTL 1)
ACPI: APIC 7F67EF70, 0068 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: BOOT 7F67EFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
ACPI: SSDT 7F6786B0, 064F (r1 SataRe SataPri 1000 INTL 20050624)
ACPI: SSDT 7F678014, 069C (r1 SataRe SataSec 1000 INTL 20050624)
ACPI: SSDT 7F677598, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050624)
ACPI: SSDT 7F6774F2, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050624)
ACPI: SSDT 7F67700C, 04E6 (r1 PmRef CpuPm 3000 INTL 20050624)
ACPI: BIOS bug: multiple APIC/MADT found, using 0
ACPI: If "acpi_apic_instance=2" works better, notify [EMAIL PROTECTED]
No NUMA configuration found
Faking a node at 0000000000000000-000000007f670000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 521840) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000007f670000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 521840
On node 0 totalpages: 521743
DMA zone: 56 pages used for memmap
DMA zone: 1043 pages reserved
DMA zone: 2900 pages, LIFO batch:0
DMA32 zone: 7078 pages used for memmap
DMA32 zone: 510666 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000
swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000d4000
swsusp: Registered nosave memory region: 00000000000d4000 - 00000000000dc000
swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 35168 bytes of per cpu data
Built 1 zonelists in Node order. Total pages: 513566
Policy zone: DMA32
Kernel command line: root=/dev/sda1 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1994.998 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2048060k/2087360k available (2061k kernel code, 38912k reserved, 978k
data, 304k init)
Calibrating delay using timer specific routine.. 3993.68 BogoMIPS (lpj=7987366)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring handled by SMI
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12468735
Detected 12.468 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.07 BogoMIPS (lpj=7980154)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: System BIOS is requesting _OSI(Linux)
ACPI: If "acpi_osi=Linux" works better,
Please send dmidecode to [EMAIL PROTECTED]
ACPI: Interpreter enabled
ACPI: (supports S0 S3)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) (try
'pci=assign-busses')
Please report the result to <[EMAIL PROTECTED]> to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: Power Resource [FN00] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: ACPI device : hid PNP0A08
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid INT0800
pnp: ACPI device : hid PNP0103
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid WEC1020
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid NSC6001
pnp: ACPI device : hid IFX0102
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0401
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid SYN1902
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
Time: hpet clocksource has been installed.
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved
pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
pnp: match found with the PnP device '00:04' and the driver 'system'
pnp: 00:04: iomem range 0xfed00000-0xfed003ff could not be reserved
pnp: match found with the PnP device '00:06' and the driver 'system'
PCI: Bridge: 0000:00:1c.0
IO window: 2000-2fff
MEM window: f0000000-f0ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: 3000-3fff
MEM window: f1000000-f1ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
IO window: 4000-4fff
MEM window: f2000000-f2ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: 5000-5fff
MEM window: f3000000-f3ffffff
PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:06.0
IO window: 00006000-000060ff
IO window: 00006400-000064ff
PREFETCH window: 88000000-8bffffff
MEM window: 90000000-93ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 6000-6fff
MEM window: f4200000-f42fffff
PREFETCH window: 88000000-8bffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:06.0[A] -> GSI 18 (level, low) -> IRQ 18
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6011k freed
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1188403247.976:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:0b' and the driver 'serial'
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:0d' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:0e' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 304k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Transitioning device [FAN0] to D3
ACPI: Transitioning device [FAN0] to D3
ACPI: Fan [FAN0] (off)
ACPI: SSDT 7F677D56, 01F6 (r1 PmRef Cpu0Ist 3000 INTL 20050624)
ACPI: SSDT 7F6777F7, 04DA (r1 PmRef Cpu0Cst 3001 INTL 20050624)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 7F677F4C, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
ACPI: SSDT 7F677CD1, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (56 C)
ACPI: Thermal Zone [TZ02] (53 C)
ACPI: Thermal Zone [TZ01] (0 C)
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf4504000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
libata version 2.21 loaded.
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf4504400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x0000000000011c00 ctl 0x00000000000118f6 bmdma
0x00000000000118e0 irq 19
ata2: SATA max UDMA/133 cmd 0x00000000000118f8 ctl 0x00000000000118f2 bmdma
0x00000000000118e8 irq 19
ata1.00: ATA-8: SAMSUNG HM121HI, LZ100-08, max UDMA7
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HM121HI LZ10 PQ: 0 ANSI: 5
tg3.c:v3.80 (August 2, 2007)
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:05:00.0 to 64
eth0: Tigon3 [partno(BCM95787m) rev b002 PHY(5787)] (PCI Express)
10/100/1000Base-T Ethernet 00:a0:d1:c2:8a:af
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:06:06.1[B] -> GSI 17 (level, low) -> IRQ 17
net eth1: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth0 to eth1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
firewire_ohci: Added fw-ohci device 0000:06:06.1, OHCI version 1.10
ICH8M: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 19 (level, low) -> IRQ 19
ICH8M: chipset revision 3
ICH8M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
firewire_core: created new fw device fw0 (0 config rom retries, S400)
Probing IDE interface ide1...
Attempting manual resume
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: Power Button (FF) as /class/input/input1
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input2
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: AC Adapter [ADP0] (on-line)
agpgart: Detected an Intel 965GM Chipset.
agpgart: Detected 7676K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
Yenta: CardBus bridge found at 0000:06:06.0 [1170:0040]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:06.0, mfunc 0x01aa1b22, devctl 0x64
ACPI: Battery Slot [BAT0] (battery present)
irda_init()
NET: Registered protocol family 23
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
pnp: the driver 'nsc-ircc' has been registered
pnp: match found with the PnP device '00:09' and the driver 'nsc-ircc'
nsc_ircc_pnp_probe() : From PnP, found firbase 0x228 ; irq 3 ; dma 3.
pnp: Device 00:09 disabled.
pnp: the driver 'nsc-ircc' has been unregistered
Yenta: ISA IRQ mask 0x0c78, PCI irq 18
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
pcmcia: parent PCI bridge Memory window: 0xf4200000 - 0xf42fffff
pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:06:06.3 [104c:803c] (rev 0)
ACPI: PCI Interrupt 0000:06:06.3[A] -> GSI 18 (level, low) -> IRQ 18
mmc0: SDHCI at 0xf4206800 irq 18 DMA
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
pnp: the driver 'tpm_inf_pnp' has been registered
pnp: match found with the PnP device '00:0a' and the driver 'tpm_inf_pnp'
tpm_inf_pnp 00:0a: Found TPM with ID IFX0102
tpm_inf_pnp 00:0a: TPM found: config base 0x4e, data base 0x1670, chip version
0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
ACPI: PCI Interrupt 0000:06:06.2[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa0b1, caps: 0xa04713/0x20040a
input: SynPS/2 Synaptics TouchPad as /class/input/input4
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:0c' and the driver 'parport_pc'
parport_pc 00:0c: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 5, dma 1
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
Adding 4562420k swap on /dev/sda5. Priority:-1 extents:1 across:4562420k
EXT3 FS on sda1, internal journal
loop: module loaded
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect
breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
tg3: eth1: Link is up at 10 Mbps, half duplex.
tg3: eth1: Flow control is off for TX and off for RX.
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.6.0 20060119 on minor 0
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
tg3: eth1: Link is up at 10 Mbps, half duplex.
tg3: eth1: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
eth1: no IPv6 routers present
eth1: no IPv6 routers present
Linux version 2.6.23-rc3-amd64 (Debian
2.6.23~rc3-1~experimental.1~snapshot.9384) ([EMAIL PROTECTED]) (gcc version
4.1.3 20070718 (prerelease) (Debian 4.1.2-14+1)) #1 SMP Mon Aug 27 23:59:33 UTC
2007
Command line: root=/dev/sda1 ro acpi=off
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f670000 (usable)
BIOS-e820: 000000007f670000 - 000000007f680000 (ACPI NVS)
BIOS-e820: 000000007f680000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 521840) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
No NUMA configuration found
Faking a node at 0000000000000000-000000007f670000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 521840) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000007f670000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 521840
On node 0 totalpages: 521743
DMA zone: 56 pages used for memmap
DMA zone: 1043 pages reserved
DMA zone: 2900 pages, LIFO batch:0
DMA32 zone: 7078 pages used for memmap
DMA32 zone: 510666 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Intel MultiProcessor Specification v1.4
MPTABLE: OEM ID: INTEL MPTABLE: Product ID: S. Rosa CRB MPTABLE: APIC at:
0xFEE00000
Processor #0 (Bootup-CPU)
Processor #1
I/O APIC #2 at 0xFEC00000.
Setting APIC routing to flat
Processors: 2
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000
swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000d4000
swsusp: Registered nosave memory region: 00000000000d4000 - 00000000000dc000
swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 35168 bytes of per cpu data
Built 1 zonelists in Node order. Total pages: 513566
Policy zone: DMA32
Kernel command line: root=/dev/sda1 ro acpi=off
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 1995.114 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2048060k/2087360k available (2061k kernel code, 38912k reserved, 978k
data, 304k init)
Calibrating delay using timer specific routine.. 3993.86 BogoMIPS (lpj=7987726)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring handled by SMI
SMP alternatives: switching to UP code
ExtINT not setup in hardware but reported by MP table
Using local APIC timer interrupts.
result 12469460
Detected 12.469 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.30 BogoMIPS (lpj=7980607)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: Using configuration type 1
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) (try
'pci=assign-busses')
Please report the result to <[EMAIL PROTECTED]> to fix this permanently
PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 16
PCI->APIC IRQ transform: 0000:00:1a.0[A] -> IRQ 16
PCI->APIC IRQ transform: 0000:00:1a.1[B] -> IRQ 21
PCI->APIC IRQ transform: 0000:00:1a.7[C] -> IRQ 18
PCI->APIC IRQ transform: 0000:00:1b.0[A] -> IRQ 22
PCI->APIC IRQ transform: 0000:00:1c.0[A] -> IRQ 17
PCI->APIC IRQ transform: 0000:00:1c.1[B] -> IRQ 16
PCI->APIC IRQ transform: 0000:00:1c.2[C] -> IRQ 18
PCI->APIC IRQ transform: 0000:00:1c.3[D] -> IRQ 19
PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 19
PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 18
PCI->APIC IRQ transform: 0000:00:1d.7[A] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:1f.1[A] -> IRQ 19
PCI->APIC IRQ transform: 0000:00:1f.2[B] -> IRQ 19
PCI->APIC IRQ transform: 0000:00:1f.3[C] -> IRQ 19
PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 16
PCI->APIC IRQ transform: 0000:05:00.0[A] -> IRQ 19
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-GART: No AMD northbridge found.
pnp: the driver 'system' has been registered
PCI: Bridge: 0000:00:1c.0
IO window: 2000-2fff
MEM window: f0000000-f0ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: 3000-3fff
MEM window: f1000000-f1ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
IO window: 4000-4fff
MEM window: f2000000-f2ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: 5000-5fff
MEM window: f3000000-f3ffffff
PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:06.0
IO window: 00006000-000060ff
IO window: 00006400-000064ff
PREFETCH window: 88000000-8bffffff
MEM window: 90000000-93ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 6000-6fff
MEM window: f4200000-f42fffff
PREFETCH window: 88000000-8bffffff
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: No IRQ known for interrupt pin C of device 0000:06:06.0. Probably buggy MP
table.
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6011k freed
audit: initializing netlink socket (disabled)
audit(1188404114.844:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
pnp: the driver 'serial' has been registered
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: the driver 'i8042 aux' has been registered
pnp: the driver 'i8042 kbd' has been unregistered
pnp: the driver 'i8042 aux' has been unregistered
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 304k freed
input: AT Translated Set 2 keyboard as /class/input/input0
thermal: Unknown symbol acpi_processor_set_thermal_limit
USB Universal Host Controller Interface driver v3.0
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf4504000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf4504400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
PCI: No IRQ known for interrupt pin D of device 0000:06:06.1. Probably buggy MP
table.
firewire_ohci: Failed to allocate shared interrupt 0.
firewire_ohci: probe of 0000:06:06.1 failed with error -5
tg3.c:v3.80 (August 2, 2007)
PCI: Setting latency timer of device 0000:05:00.0 to 64
eth0: Tigon3 [partno(BCM95787m) rev b002 PHY(5787)] (PCI Express)
10/100/1000Base-T Ethernet 00:a0:d1:c2:8a:af
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
net eth1: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth0 to eth1
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x0000000000011c00 ctl 0x00000000000118f6 bmdma
0x00000000000118e0 irq 19
ata2: SATA max UDMA/133 cmd 0x00000000000118f8 ctl 0x00000000000118f2 bmdma
0x00000000000118e8 irq 19
ata1.00: ATA-8: SAMSUNG HM121HI, LZ100-08, max UDMA7
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HM121HI LZ10 PQ: 0 ANSI: 5
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
ICH8M: IDE controller at PCI slot 0000:00:1f.1
ICH8M: chipset revision 3
ICH8M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hdb: TSSTcorp CDDVDW SN-S082H, ATAPI CD/DVD-ROM drive
hdb: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda:<6>hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sda1 sda2 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
Attempting manual resume
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
agpgart: Detected an Intel 965GM Chipset.
agpgart: Detected 7676K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
Yenta: CardBus bridge found at 0000:06:06.0 [1170:0040]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:06.0, mfunc 0x01aa1b22, devctl 0x64
Yenta TI: socket 0000:06:06.0 no PCI interrupts. Fish. Please report.
Yenta: no PCI IRQ, CardBus support disabled for this socket.
Yenta: check your BIOS CardBus, BIOS IRQ or ACPI settings.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
Yenta: ISA IRQ mask 0x0278, PCI irq 0
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
pcmcia: parent PCI bridge Memory window: 0xf4200000 - 0xf42fffff
pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
PCI: No IRQ known for interrupt pin C of device 0000:06:06.2. Probably buggy MP
table.
tifm_7xx1: probe of 0000:06:06.2 failed with error -16
sdhci: SDHCI controller found at 0000:06:06.3 [104c:803c] (rev 0)
PCI: No IRQ known for interrupt pin C of device 0000:06:06.3. Probably buggy MP
table.
sdhci: probe of 0000:06:06.3 failed with error -16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa0b1, caps: 0xa04713/0x20040a
input: SynPS/2 Synaptics TouchPad as /class/input/input1
Adding 4562420k swap on /dev/sda5. Priority:-1 extents:1 across:4562420k
EXT3 FS on sda1, internal journal
loop: module loaded
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect
breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
acpi_cpufreq: Unknown symbol acpi_processor_unregister_performance
acpi_cpufreq: Unknown symbol acpi_processor_preregister_performance
acpi_cpufreq: Unknown symbol acpi_processor_register_performance
acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
acpi_cpufreq: Unknown symbol acpi_processor_unregister_performance
acpi_cpufreq: Unknown symbol acpi_processor_preregister_performance
acpi_cpufreq: Unknown symbol acpi_processor_register_performance
tg3: eth1: Link is up at 10 Mbps, half duplex.
tg3: eth1: Flow control is off for TX and off for RX.
pnp: the driver 'parport_pc' has been registered
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 5 detected
lp0: using parport0 (polling).
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized i915 1.6.0 20060119 on minor 0
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth1: no IPv6 routers present
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory
Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated
Graphics Controller (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Contoller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1
(rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2
(rev 03)
00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3
(rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4
(rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller
(rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE
Controller (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA IDE
Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
02:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN
Network Connection (rev 61)
05:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit
Ethernet PCI Express (rev 02)
06:06.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
06:06.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE
1394 Host Controller
06:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card
Reader (SD/MMC/MS/MS PRO/xD)
06:06.3 Generic system peripheral [0805]: Texas Instruments PCIxx12 SDA
Standard Compliant SD Host Controller
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory
Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated
Graphics Controller (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Contoller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1
(rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2
(rev 03)
00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3
(rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4
(rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller
(rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE
Controller (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA IDE
Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
02:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN
Network Connection (rev 61)
05:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit
Ethernet PCI Express (rev 02)
06:06.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
06:06.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE
1394 Host Controller
06:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card
Reader (SD/MMC/MS/MS PRO/xD)
06:06.3 Generic system peripheral [0805]: Texas Instruments PCIxx12 SDA
Standard Compliant SD Host Controller
