Package: linux-2.6
Version: 3.2.4-1
Severity: normal
Hi,
after upgrading the kernel from 3.1.0-1 to 3.2.0-1 on a machine running Debian
testing, the sky2 driver seems to take over 70 sec to bring up the ethernet
link. Also, the reported link speed does not seem to be correct.
This is what I see with 3.2.0-1:
root@sirius:/data/home/jr/clamz# dmesg | grep sky
[ 1.562738] sky2: driver version 1.30
[ 1.562763] sky2 0000:05:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.562774] sky2 0000:05:00.0: setting latency timer to 64
[ 1.562798] sky2 0000:05:00.0: Yukon-2 EC Ultra chip revision 3
[ 1.562890] sky2 0000:05:00.0: irq 73 for MSI/MSI-X
[ 1.565365] sky2 0000:05:00.0: eth0: addr bc:ae:c5:02:86:33
[ 18.485687] sky2 0000:05:00.0: eth0: enabling interface
[ 84.967943] sky2 0000:05:00.0: eth0: Link is up at 100 Mbps, full duplex,
flow control both
Note that the driver claims that link speed is 100Mbit, however the remote end
(AVM Fritzbox 7390) claims the link speed is 1Gbit.
Other then running a "apt-get dist-upgrade", which led to the kernel (and other
packages) being upgraded, no changes were made to the networking setup. In
particular, no changes were made to the physical setup (cabling etc), and the
setup was working fine with 3.1.0-1 before.
Best regards,
-jr
-- Package-specific info:
** Version:
Linux version 3.2.0-1-amd64 (Debian 3.2.4-1) (wa...@debian.org) (gcc version
4.6.2 (Debian 4.6.2-12) ) #1 SMP Sun Feb 5 15:17:15 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-1-amd64
root=UUID=f9cee7b2-5c98-4492-b621-7437de765f42 ro quiet
** Tainted: PO (4097)
* Proprietary module has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[ 3.407759] usb 3-5.1: new full-speed USB device number 4 using ehci_hcd
[ 3.519078] usb 3-5.1: New USB device found, idVendor=0409, idProduct=02b9
[ 3.519082] usb 3-5.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 3.519085] usb 3-5.1: Product: PA271W
[ 3.519088] usb 3-5.1: Manufacturer: NEC
[ 3.519090] usb 3-5.1: SerialNumber: 11102966UB
[ 3.631313] ata5: SATA link down (SStatus 0 SControl 300)
[ 3.951167] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.951650] scsi 6:0:0:0: Direct-Access ATA OCZ-VERTEX3 MI 2.02
PQ: 0 ANSI: 5
[ 3.952420] scsi 13:0:0:0: Processor Marvell 91xx Config 1.01
PQ: 0 ANSI: 5
[ 3.953661] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 3.953893] sd 0:0:0:0: [sda] Write Protect is off
[ 3.953895] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.953915] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 3.957726] sr0: scsi3-mmc drive: 94x/94x writer dvd-ram cd/rw xa/form2 cdda
tray
[ 3.957730] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.957944] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 3.958099] sd 6:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/111
GiB)
[ 3.958228] sd 6:0:0:0: [sdb] Write Protect is off
[ 3.958230] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.958334] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 3.958710] sdb: sdb1 sdb2 sdb3
[ 3.959007] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 3.985652] sda: sda1 sda2 sda3
[ 3.986824] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.514765] generic-usb 0003:0409:02B9.0005: timeout initializing reports
[ 13.515119] generic-usb 0003:0409:02B9.0005: hiddev0,hidraw4: USB HID v1.10
Device [NEC PA271W] on usb-0000:00:1a.7-5.1/input0
[ 13.978182] device-mapper: uevent: version 1.0.3
[ 13.978227] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised:
dm-de...@redhat.com
[ 14.128888] PM: Starting manual resume from disk
[ 14.128891] PM: Hibernation image partition 8:3 present
[ 14.128892] PM: Looking for hibernation image.
[ 14.129063] PM: Image not found (code -22)
[ 14.129067] PM: Hibernation image not present or could not be loaded.
[ 14.135764] kjournald starting. Commit interval 5 seconds
[ 14.135792] EXT3-fs (sdb3): mounted filesystem with ordered data mode
[ 14.477014] udevd[412]: starting version 175
[ 14.529269] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 14.529274] ACPI: Power Button [PWRB]
[ 14.529325] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 14.529328] ACPI: Power Button [PWRF]
[ 14.533966] wmi: Mapper loaded
[ 14.546851] iTCO_vendor_support: vendor-support=0
[ 14.548392] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 14.548490] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0860)
[ 14.548546] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 14.548710] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ
18
[ 14.548715] ACPI: resource 0000:00:1f.3 [io 0x1000-0x101f] conflicts with
ACPI region SMRG [io 0x1000-0x100f]
[ 14.548717] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 14.552920] EDAC MC: Ver: 2.1.0
[ 14.555439] EDAC MC0: Giving out device to 'i7core_edac.c' 'i7 core #0': DEV
0000:ff:03.0
[ 14.555454] EDAC PCI0: Giving out device to module 'i7core_edac' controller
'EDAC PCI controller': DEV '0000:ff:03.0' (POLLED)
[ 14.555461] EDAC i7core: Driver loaded, 1 memory controller(s) found.
[ 14.559008] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 14.742443] input: Audio Kontrol 1 as
/devices/pci0000:00/0000:00:1d.7/usb4/4-3/input/input7
[ 14.743065] usbcore: registered new interface driver snd-usb-caiaq
[ 14.761202] Disabling lock debugging due to kernel taint
[ 14.761207] nvidia: module license 'NVIDIA' taints kernel.
[ 14.850132] nvidia 0000:03:00.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
[ 14.850140] nvidia 0000:03:00.0: setting latency timer to 64
[ 14.850144] vgaarb: device changed decodes:
PCI:0000:03:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 14.850535] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 295.20 Mon Feb
6 21:07:30 PST 2012
[ 17.730540] Adding 5859324k swap on /dev/sda3. Priority:-1 extents:1
across:5859324k
[ 17.761619] EXT3-fs (sdb3): using internal journal
[ 17.808566] loop: module loaded
[ 17.813859] w83627ehf: Found W83667HG chip at 0x290
[ 17.813874] ACPI: resource w83627ehf [io 0x0295-0x0296] conflicts with ACPI
region HWRE [io 0x290-0x299]
[ 17.813876] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 18.340231] kjournald starting. Commit interval 5 seconds
[ 18.340740] EXT3-fs (sda2): using internal journal
[ 18.340746] EXT3-fs (sda2): mounted filesystem with ordered data mode
[ 18.479393] Bridge firewalling registered
[ 18.481645] device eth0 entered promiscuous mode
[ 18.485687] sky2 0000:05:00.0: eth0: enabling interface
[ 18.486189] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.488500] ADDRCONF(NETDEV_UP): br0: link is not ready
[ 28.604705] fuse init (API version 7.17)
[ 29.282847] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly.
Using workaround
[ 30.223607] Bluetooth: Core ver 2.16
[ 30.223621] NET: Registered protocol family 31
[ 30.223622] Bluetooth: HCI device and connection manager initialized
[ 30.223624] Bluetooth: HCI socket layer initialized
[ 30.223625] Bluetooth: L2CAP socket layer initialized
[ 30.223630] Bluetooth: SCO socket layer initialized
[ 30.233170] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 30.233172] Bluetooth: BNEP filters: protocol multicast
[ 30.252461] Bluetooth: RFCOMM TTY layer initialized
[ 30.252468] Bluetooth: RFCOMM socket layer initialized
[ 30.252469] Bluetooth: RFCOMM ver 1.11
[ 30.531035] Ebtables v2.0 registered
[ 30.538408] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 30.543554] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 38.715802] UDF-fs: Partition marked readonly; forcing readonly mount
[ 38.752810] UDF-fs: INFO Mounting volume 'MassEffect2', timestamp 2010/01/04
21:41 (1000)
[ 84.967943] sky2 0000:05:00.0: eth0: Link is up at 100 Mbps, full duplex,
flow control both
[ 84.968835] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 84.968862] br0: port 1(eth0) entering forwarding state
[ 84.968984] br0: port 1(eth0) entering forwarding state
[ 84.970022] ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 95.887986] br0: no IPv6 routers present
** Model information
sys_vendor: System manufacturer
product_name: System Product Name
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 0602
board_vendor: ASUSTeK Computer INC.
board_name: P6X58D-E
board_version: Rev 1.xx
** Loaded modules:
nls_utf8
udf
ip6table_filter
ip6_tables
iptable_filter
ip_tables
ebtable_nat
ebtables
x_tables
acpi_cpufreq
mperf
cpufreq_userspace
cpufreq_conservative
cpufreq_powersave
cpufreq_stats
rfcomm
bnep
bluetooth
rfkill
crc16
binfmt_misc
kvm_intel
kvm
fuse
bridge
stp
snd_aloop
hwmon_vid
coretemp
loop
firewire_sbp2
nvidia(P)
snd_usb_caiaq
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_pcm
snd_seq
snd_timer
snd_seq_device
snd
soundcore
snd_page_alloc
mxm_wmi
psmouse
pcspkr
serio_raw
joydev
evdev
i7core_edac
edac_core
i2c_i801
iTCO_wdt
iTCO_vendor_support
i2c_core
asus_atk0110
wmi
button
processor
thermal_sys
ext3
jbd
mbcache
dm_mod
sd_mod
sr_mod
cdrom
usbhid
hid
crc_t10dif
uhci_hcd
firewire_ohci
firewire_core
crc_itu_t
ahci
libahci
ehci_hcd
sky2
xhci_hcd
libata
usbcore
scsi_mod
usb_common
** Network interface configuration:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet manual
auto br0
iface br0 inet static
address 192.168.178.10
netmask 255.255.255.0
gateway 192.168.178.1
bridge_ports eth0
bridge_stp off
bridge_fd 0
bridge_maxwait 0
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master br0
state UP qlen 1000
link/ether bc:ae:c5:02:86:33 brd ff:ff:ff:ff:ff:ff
3: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
link/ether bc:ae:c5:02:86:33 brd ff:ff:ff:ff:ff:ff
inet 192.168.178.10/24 brd 192.168.178.255 scope global br0
inet6 fe80::beae:c5ff:fe02:8633/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 7709 91 0 0 0 0 0 0 7709
91 0 0 0 0 0 0
br0: 16592295 14304 0 0 0 0 0 0 1171706
10309 0 0 0 0 0 0
eth0: 16797403 14372 0 0 0 0 0 114 1171832
10310 0 0 0 0 0 0
*** Protocol statistics:
Ip:
14428 total packets received
0 forwarded
0 incoming packets discarded
14420 incoming packets delivered
10515 requests sent out
12 dropped because of missing route
Icmp:
100 ICMP messages received
8 input ICMP message failed.
ICMP input histogram:
destination unreachable: 62
echo replies: 38
134 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 61
echo request: 73
IcmpMsg:
InType0: 38
InType3: 62
OutType3: 61
OutType8: 73
Tcp:
249 active connections openings
0 passive connection openings
18 failed connection attempts
3 connection resets received
21 connections established
13170 segments received
9193 segments send out
8 segments retransmited
0 bad segments received.
113 resets sent
Udp:
1066 packets received
1 packets to unknown port received.
0 packet receive errors
1182 packets sent
UdpLite:
TcpExt:
84 TCP sockets finished time wait in fast timer
218 delayed acks sent
Quick ack mode was activated 3 times
11246 packet headers predicted
537 acknowledgments not containing data payload received
689 predicted acknowledgments
4 other TCP timeouts
3 DSACKs sent for old packets
18 connections reset due to unexpected data
2 connections reset due to early user close
IpExt:
InMcastPkts: 97
OutMcastPkts: 81
InBcastPkts: 72
OutBcastPkts: 7
InOctets: 16606292
OutOctets: 1041935
InMcastOctets: 10400
OutMcastOctets: 8816
InBcastOctets: 4828
OutBcastOctets: 328
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port
[8086:3405] (rev 13)
Subsystem: ASUSTeK Computer Inc. Device [1043:836b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f9e00000-f9efffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 2 [8086:3409] (rev 13) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: f9f00000-f9ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fa000000-fbcfffff
Prefetchable memory behind bridge: 00000000d6000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:14.0 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub System Management
Registers [8086:342e] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: i7core_edac
00:14.1 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch
Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.2 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Control Status and
RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.3 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers
[8086:3438] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #4 [8086:3a37] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at a800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #5 [8086:3a38] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at a880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at ac00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #2 [8086:3a3c] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f9dff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801JI (ICH10 Family) HD Audio
Controller [8086:3a3e]
Subsystem: ASUSTeK Computer Inc. Device [1043:8418]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 4
Region 0: Memory at f9df8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 1 [8086:3a40] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: c0200000-c05fffff
Prefetchable memory behind bridge: 00000000f8f00000-00000000f8ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 3 [8086:3a44] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbd00000-fbdfffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at a080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at a480 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f9dfe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
90) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbe00000-fbefffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIR (ICH10R) LPC Interface
Controller [8086:3a16]
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller [8086:3a22] (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 77
Region 0: I/O ports at 9c00 [size=8]
Region 1: I/O ports at 9880 [size=4]
Region 2: I/O ports at 9800 [size=8]
Region 3: I/O ports at 9480 [size=4]
Region 4: I/O ports at 9400 [size=32]
Region 5: Memory at f9dfc000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
[8086:3a30]
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f9dfd000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1000 [size=32]
01:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9123 PCIe
SATA 6.0 Gb/s controller [1b4b:9123] (rev 11) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:8400]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 78
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=16]
Region 5: Memory at f9eff800 (32-bit, non-prefetchable) [size=2K]
Expansion ROM at f9ee0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
02:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host
Controller [1033:0194] (rev 03) (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [1043:8413]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f9ffe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
03:00.0 VGA compatible controller [0300]: nVidia Corporation GF110 [GeForce GTX
580] [10de:1080] (rev a1) (prog-if 00 [VGA controller])
Subsystem: CardExpert Technology Device [10b0:0401]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 24
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at d6000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at cc00 [size=128]
[virtual] Expansion ROM at fbc00000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nvidia
03:00.1 Audio device [0403]: nVidia Corporation GF110 High Definition Audio
Controller [10de:0e09] (rev a1)
Subsystem: CardExpert Technology Device [10b0:0401]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin B routed to IRQ 11
Region 0: Memory at fbcfc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
05:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E
Gigabit Ethernet Controller [11ab:4364] (rev 12)
Subsystem: ASUSTeK Computer Inc. Device [1043:81f8]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 73
Region 0: Memory at fbdfc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at d800 [size=256]
Expansion ROM at fbdc0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: sky2
07:02.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire
II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. M4A series motherboard [1043:81fe]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fbeff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ec00 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
ff:00.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QuickPath
Architecture Generic Non-Core Registers [8086:2c41] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:00.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QuickPath
Architecture System Address Decoder [8086:2c01] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QPI Link 0
[8086:2c10] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QPI Physical 0
[8086:2c11] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller [8086:2c18] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Target Address Decoder [8086:2c19] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.4 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Test Registers [8086:2c1c] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 0 Control Registers [8086:2c20] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 0 Address Registers [8086:2c21] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.2 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 0 Rank Registers [8086:2c22] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.3 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 0 Thermal Control Registers [8086:2c23] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 1 Control Registers [8086:2c28] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 1 Address Registers [8086:2c29] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.2 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 1 Rank Registers [8086:2c2a] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.3 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 1 Thermal Control Registers [8086:2c2b] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 2 Control Registers [8086:2c30] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 2 Address Registers [8086:2c31] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.2 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 2 Rank Registers [8086:2c32] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.3 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated
Memory Controller Channel 2 Thermal Control Registers [8086:2c33] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 0409:005a NEC Corp. HighSpeed Hub
Bus 004 Device 002: ID 17cc:0815 Native Instruments Audio Kontrol 1
Bus 007 Device 002: ID 045e:0780 Microsoft Corp.
Bus 009 Device 002: ID 046d:c066 Logitech, Inc.
Bus 003 Device 004: ID 0409:02b9 NEC Corp.
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-1-amd64 (SMP w/8 CPU cores)
Locale: LANG=”en_US.UTF-8″, LC_CTYPE=de_AT.utf8 (charmap=UTF-8) (ignored:
LC_ALL set to en_US.utf8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.41
ii initramfs-tools [linux-initramfs-tool] 0.100
ii linux-base 3.4
ii module-init-tools 3.16-1
Versions of packages linux-image-3.2.0-1-amd64 recommends:
ii firmware-linux-free 3
Versions of packages linux-image-3.2.0-1-amd64 suggests:
pn grub-pc 1.99-14
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-1-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-1-amd64/postinst/depmod-error-initrd-3.2.0-1-amd64: false
linux-image-3.2.0-1-amd64/postinst/missing-firmware-3.2.0-1-amd64:
linux-image-3.2.0-1-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-1-amd64/prerm/removing-running-kernel-3.2.0-1-amd64: true
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
