Package: linux-2.6 Version: 2.6.32-31 Severity: normal *** Please type your report below this line ***
I was install a Debian Squeeze amd64 on the next hardware: HP Proliant ML350 G5, with 16 GB of RAM and a HBA fibre channel card: Brocade. Viewing the dmesg ouput: $ dmesg | grep cbfw [ 2.454760] bfa 0000:09:00.0: firmware: requesting cbfw.bin [ 2.600597] Can't locate firmware cbfw.bin [ 2.600687] bfa 0000:09:00.1: firmware: requesting cbfw.bin [ 2.602660] Can't locate firmware cbfw.bin and Reading the wiki page: [0] http://wiki.debian.org/Firmware I found that I need the file: cbfw.bin for put to work my HBA Card. Then I do a search inside Debian packages [1] http://packages.debian.org/file%3Acbfw.bin and I not found the file. At the site of the provider [2] http://www.brocade.com/forms/getFile?p=documents/downloads/HBA/Linux/Drivers/NOARCH/bfa_firmware_linux-2.3.2.3-0.src.rpm, I can found the files: cbfw_fc.bin, ctfw_cna.bin, ctfw_fc.bin but, there is no the file I need, Searching on Internet I found [3] http://rpmfind.net/linux/RPM/fedora/14/x86_64/bfa-firmware-2.1.2.1-2.fc14.noarch.html this rpm package have the file, but putting it to my /lib/firmware/ directory I get: [85557.919970] scsi5 : Brocade FC/FCOE Adapter, model: Brocade-425 hwpath: 0000:09:00.1 driver: 2.0.0.0 [85559.296591] BFA[error] HAL_ASSERT: Assertion failure: /build/buildd-linux-2.6_2.6.32-30-amd64-d4MbNM/linux-2.6-2.6.32/debian/build/source_amd64_none/drivers/scsi/bfa/bfa_fcport.c:972: Thanks a lot for your time, and sorry for my English, I am a Spanish speaker. -- Package-specific info: ** Version: Linux version 2.6.32-5-amd64 (Debian 2.6.32-31) (b...@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Mon Mar 7 21:35:22 UTC 2011 ** Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=UUID=8259d99b-7476-414b-bd1e-00d9199e24c6 ro quiet ** Not tainted ** Kernel log: [ 2.829960] hub 4-0:1.0: 2 ports detected [ 2.830011] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 2.830016] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 2.830019] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 2.830027] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 [ 2.830056] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00001060 [ 2.830093] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.830095] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.830097] usb usb5: Product: UHCI Host Controller [ 2.830099] usb usb5: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd [ 2.830101] usb usb5: SerialNumber: 0000:00:1d.3 [ 2.830159] usb usb5: configuration #1 chosen from 1 choice [ 2.830185] hub 5-0:1.0: USB hub found [ 2.830192] hub 5-0:1.0: 2 ports detected [ 2.830250] uhci_hcd 0000:01:04.4: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [ 2.830257] uhci_hcd 0000:01:04.4: UHCI Host Controller [ 2.830266] uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 6 [ 2.830278] uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports [ 2.831242] uhci_hcd 0000:01:04.4: irq 22, io base 0x00003800 [ 2.831509] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.831511] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.831513] usb usb6: Product: UHCI Host Controller [ 2.831515] usb usb6: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd [ 2.831517] usb usb6: SerialNumber: 0000:01:04.4 [ 2.831626] usb usb6: configuration #1 chosen from 1 choice [ 2.831658] hub 6-0:1.0: USB hub found [ 2.831665] hub 6-0:1.0: 2 ports detected [ 2.833687] 0000:0f:00.0: eth0: (PCI Express:2.5GB/s:Width x4) 00:1f:29:54:ca:de [ 2.833691] 0000:0f:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 2.833767] 0000:0f:00.0: eth0: MAC: 0, PHY: 4, PBA No: d51930-004 [ 2.833802] e1000e 0000:0f:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 2.833820] e1000e 0000:0f:00.1: setting latency timer to 64 [ 2.833909] alloc irq_desc for 58 on node -1 [ 2.833911] alloc kstat_irqs on node -1 [ 2.833924] e1000e 0000:0f:00.1: irq 58 for MSI/MSI-X [ 2.860947] ipmi: Found new BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11) [ 2.860956] IPMI kcs interface initialized [ 2.860971] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0 [ 2.860973] ipmi_si: duplicate interface [ 2.876554] ipmi_si 0000:01:04.6: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 2.876558] ipmi_si: Trying PCI-specified kcs state machine at mem address 0xf9ef0000, slave address 0x0, irq 21 [ 2.971732] ata1.01: NODEV after polling detection [ 2.976236] ata1.00: ATAPI: HL-DT-ST DVD-RAM GH15L, FA01, max UDMA/100 [ 2.992249] ata1.00: configured for UDMA/100 [ 2.997569] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH15L FA01 PQ: 0 ANSI: 5 [ 3.000533] IRQ 21/ipmi_si: IRQF_DISABLED is not guaranteed on shared IRQs [ 3.000548] Using irq 21 [ 3.019589] 0000:0f:00.1: eth1: (PCI Express:2.5GB/s:Width x4) 00:1f:29:54:ca:df [ 3.019592] 0000:0f:00.1: eth1: Intel(R) PRO/1000 Network Connection [ 3.019668] 0000:0f:00.1: eth1: MAC: 0, PHY: 4, PBA No: d51930-004 [ 3.033641] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 3.033645] Uniform CD-ROM driver Revision: 3.20 [ 3.033748] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 3.070380] sr 0:0:0:0: Attached scsi generic sg0 type 5 [ 3.141298] usb 6-1: new full speed USB device using uhci_hcd and address 2 [ 3.148531] bnx2 0000:03:00.0: firmware: requesting bnx2/bnx2-mips-06-5.0.0.j3.fw [ 3.175074] bnx2 0000:03:00.0: firmware: requesting bnx2/bnx2-rv2p-06-5.0.0.j3.fw [ 3.184526] eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem fa000000, IRQ 16, node addr 00:23:7d:3b:5f:b4 [ 3.190739] ipmi: interfacing existing BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11) [ 3.190758] IPMI kcs interface initialized [ 3.287299] usb 6-1: New USB device found, idVendor=03f0, idProduct=1027 [ 3.287303] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.287305] usb 6-1: Product: Virtual Keyboard [ 3.287307] usb 6-1: Manufacturer: HP [ 3.287413] usb 6-1: configuration #1 chosen from 1 choice [ 3.382055] usbcore: registered new interface driver hiddev [ 3.386042] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:1e.0/0000:01:04.4/usb6/6-1/6-1:1.0/input/input3 [ 3.386119] generic-usb 0003:03F0:1027.0001: input,hidraw0: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1/input0 [ 3.392430] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:1e.0/0000:01:04.4/usb6/6-1/6-1:1.1/input/input4 [ 3.392508] generic-usb 0003:03F0:1027.0002: input,hidraw1: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1/input1 [ 3.392529] usbcore: registered new interface driver usbhid [ 3.392532] usbhid: v2.6:USB HID core driver [ 3.405030] usb 6-2: new full speed USB device using uhci_hcd and address 3 [ 3.555143] usb 6-2: New USB device found, idVendor=03f0, idProduct=1327 [ 3.555147] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.555149] usb 6-2: Product: Virtual Hub [ 3.555151] usb 6-2: Manufacturer: HP [ 3.555230] usb 6-2: configuration #1 chosen from 1 choice [ 3.560663] hub 6-2:1.0: USB hub found [ 3.562866] hub 6-2:1.0: 7 ports detected [ 3.572413] Adding 62499832k swap on /dev/cciss/c0d0p2. Priority:-1 extents:1 across:62499832k [ 3.803217] loop: module loaded [ 4.024610] EXT4-fs (cciss!c0d0p5): mounted filesystem with ordered data mode [ 4.544281] e1000e 0000:0f:00.0: irq 57 for MSI/MSI-X [ 4.600067] e1000e 0000:0f:00.0: irq 57 for MSI/MSI-X [ 4.602493] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.161887] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 6.161892] 0000:0f:00.0: eth0: 10/100 speed: disabling TSO [ 6.164199] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.634971] alloc irq_desc for 59 on node -1 [ 6.634975] alloc kstat_irqs on node -1 [ 6.634993] bnx2 0000:03:00.0: irq 59 for MSI/MSI-X [ 6.753778] bnx2: eth2: using MSI [ 6.756097] ADDRCONF(NETDEV_UP): eth2: link is not ready [ 8.772247] JBD: barrier-based sync failed on cciss!c0d0p1-8 - disabling barriers [ 9.927460] bnx2: eth2 NIC Copper Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON [ 9.929827] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 16.540022] eth0: no IPv6 routers present [ 20.828520] eth2: no IPv6 routers present [ 9478.816495] JBD: barrier-based sync failed on cciss!c0d0p5-8 - disabling barriers ** Model information sys_vendor: HP product_name: ProLiant ML350 G5 product_version: chassis_vendor: HP chassis_version: bios_vendor: HP bios_version: D21 ** Loaded modules: Module Size Used by kvm_intel 38146 0 kvm 214088 1 kvm_intel loop 11799 0 usbhid 33292 0 hid 63257 1 usbhid sg 18744 0 sr_mod 12602 0 cdrom 29415 1 sr_mod ata_generic 3047 0 radeon 574188 0 ttm 40146 1 radeon drm_kms_helper 20065 1 radeon drm 142359 3 radeon,ttm,drm_kms_helper uhci_hcd 18521 0 bfa 231363 0 i5000_edac 7284 0 i2c_algo_bit 4225 1 radeon ipmi_si 30960 0 ehci_hcd 32081 0 edac_core 29261 3 i5000_edac scsi_transport_fc 35355 1 bfa ipmi_msghandler 26634 1 ipmi_si i2c_core 15819 4 radeon,drm_kms_helper,drm,i2c_algo_bit bnx2 57385 0 usbcore 122386 4 usbhid,uhci_hcd,ehci_hcd scsi_tgt 8482 1 scsi_transport_fc hpwdt 4916 0 hpilo 6268 0 i5k_amb 4439 0 ata_piix 21124 0 rng_core 3006 0 psmouse 49937 0 e1000e 110063 0 floppy 49087 0 libata 133632 2 ata_generic,ata_piix evdev 7352 2 container 2389 0 pcspkr 1699 0 processor 29935 8 serio_raw 3752 0 button 4650 0 nls_base 6377 1 usbcore ext4 289033 2 mbcache 5050 1 ext4 jbd2 67015 1 ext4 crc16 1319 1 ext4 cciss 83334 4 scsi_mod 122149 7 sg,sr_mod,bfa,scsi_transport_fc,scsi_tgt,libata,cciss shpchp 26264 0 thermal 11674 0 thermal_sys 11942 2 processor,thermal pci_hotplug 21203 1 shpchp ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 5000Z Chipset Memory Controller Hub [8086:25d0] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 [8086:25f7] (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=0e, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: fdb00000-fddfffff Prefetchable memory behind bridge: 00000000f8000000-00000000f81fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 [8086:25e3] (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=17, subordinate=19, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:04.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 4 [8086:25e4] (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0f, subordinate=11, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000f8200000-00000000f82fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 [8086:25e5] (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=12, subordinate=16, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: 00000000f8300000-00000000f83fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel driver in use: i5000_edac 00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f1] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f3] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f5] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f6] (rev b1) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1c.0 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 [8086:2690] (rev 09) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=03, sec-latency=0 Memory behind bridge: fa000000-fbffffff Prefetchable memory behind bridge: 00000000f8400000-00000000f84fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 [8086:2688] (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at 1000 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 [8086:2689] (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at 1020 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 [8086:268a] (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 1040 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 [8086:268b] (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at 1060 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller [8086:268c] (rev 09) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f9df0000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev d9) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00002000-00003fff Memory behind bridge: f9e00000-f9ffffff Prefetchable memory behind bridge: 00000000f0000000-00000000f7ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller [8086:2670] (rev 09) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.2 IDE interface [0101]: Intel Corporation 631xESB/632xESB/3100 Chipset SATA IDE Controller [8086:2680] (rev 09) (prog-if 80 [Master]) Subsystem: Compaq Computer Corporation Device [0e11:3201] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 0500 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 01:03.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000 [1002:515e] (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device [103c:31fb] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 23 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 3000 [size=256] Region 2: Memory at f9ff0000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at f9e00000 [disabled] [size=128K] Capabilities: <access denied> 01:04.0 System peripheral [0880]: Compaq Computer Corporation Integrated Lights Out Controller [0e11:b203] (rev 03) Subsystem: Hewlett-Packard Company Device [103c:3305] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at 2800 [size=256] Region 1: Memory at f9fe0000 (32-bit, non-prefetchable) [size=512] Capabilities: <access denied> Kernel driver in use: hpwdt 01:04.2 System peripheral [0880]: Compaq Computer Corporation Integrated Lights Out Processor [0e11:b204] (rev 03) Subsystem: Hewlett-Packard Company Device [103c:3305] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 22 BIST result: 00 Region 0: I/O ports at 3400 [size=256] Region 1: Memory at f9fd0000 (32-bit, non-prefetchable) [size=2K] Region 2: Memory at f9fc0000 (32-bit, non-prefetchable) [size=8K] Region 3: Memory at f9f00000 (32-bit, non-prefetchable) [size=512K] [virtual] Expansion ROM at f9e20000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: hpilo 01:04.4 USB Controller [0c03]: Hewlett-Packard Company Proliant iLO2/iLO3 virtual USB controller [103c:3300] (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:3305] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin B routed to IRQ 22 Region 4: I/O ports at 3800 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 01:04.6 IPMI SMIC interface [0c07]: Hewlett-Packard Company Proliant iLO2 virtual UART [103c:3302] (prog-if 01) Subsystem: Hewlett-Packard Company Device [103c:3305] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 21 Region 0: Memory at f9ef0000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ipmi_si 02:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge [1166:0103] (rev c3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=02, secondary=03, subordinate=03, sec-latency=64 Memory behind bridge: fa000000-fbffffff Prefetchable memory behind bridge: 00000000f8400000-00000000f84fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 03:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet [14e4:164c] (rev 12) Subsystem: Hewlett-Packard Company NC373i Integrated Multifunction Gigabit Server Adapter [103c:7038] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (16000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 59 Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=32M] [virtual] Expansion ROM at f8400000 [disabled] [size=2K] Capabilities: <access denied> Kernel driver in use: bnx2 04:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port [8086:3500] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=04, secondary=05, subordinate=0b, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: fdc00000-fddfffff Prefetchable memory behind bridge: 00000000f8000000-00000000f81fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 04:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge [8086:350c] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=04, secondary=0c, subordinate=0e, sec-latency=64 Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 05:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 [8086:3510] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=05, secondary=06, subordinate=08, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 05:01.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E2 [8086:3514] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=05, secondary=09, subordinate=0b, sec-latency=0 Memory behind bridge: fdd00000-fddfffff Prefetchable memory behind bridge: 00000000f8100000-00000000f81fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 06:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge [1166:0103] (rev b4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=06, secondary=07, subordinate=08, sec-latency=64 I/O behind bridge: 00004000-00004fff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 07:04.0 PCI bridge [0604]: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge [1166:0104] (rev b2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Bus: primary=07, secondary=08, subordinate=08, sec-latency=64 Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 07:08.0 RAID bus controller [0104]: Hewlett-Packard Company Smart Array E200i (SAS Controller) [103c:3238] Subsystem: Hewlett-Packard Company Smart Array E200 [103c:3212] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr+ DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx- Latency: 64 Interrupt: pin A routed to IRQ 55 Region 0: Memory at fdc80000 (64-bit, non-prefetchable) [size=512K] Region 2: I/O ports at 4000 [size=256] Region 3: Memory at fdc70000 (32-bit, non-prefetchable) [size=32K] [virtual] Expansion ROM at f8000000 [disabled] [size=16K] Capabilities: <access denied> Kernel driver in use: cciss 09:00.0 Fibre Channel [0c04]: Brocade Communications Systems, Inc. 425/825/42B/82B 4Gbps/8Gbps PCIe dual port FC HBA [1657:0013] (rev 01) Subsystem: Hewlett-Packard Company HP 42B 4Gbps dual port FC HBA [103c:1744] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 7 Region 0: Memory at fdde0000 (64-bit, non-prefetchable) [size=128K] Region 2: Memory at fddd0000 (64-bit, non-prefetchable) [size=16K] [virtual] Expansion ROM at f8100000 [disabled] [size=512K] Capabilities: <access denied> 09:00.1 Fibre Channel [0c04]: Brocade Communications Systems, Inc. 425/825/42B/82B 4Gbps/8Gbps PCIe dual port FC HBA [1657:0013] (rev 01) Subsystem: Hewlett-Packard Company HP 42B 4Gbps dual port FC HBA [103c:1744] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 10 Region 0: Memory at fdda0000 (64-bit, non-prefetchable) [size=128K] Region 2: Memory at fdd90000 (64-bit, non-prefetchable) [size=16K] [virtual] Expansion ROM at f8180000 [disabled] [size=512K] Capabilities: <access denied> 0f:00.0 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit Ethernet Controller [8086:105e] (rev 06) Subsystem: Hewlett-Packard Company NC360T PCI Express Dual Port Gigabit Server Adapter [103c:7044] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 57 Region 0: Memory at fdee0000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at fdec0000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 5000 [size=32] [virtual] Expansion ROM at f8200000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: e1000e 0f:00.1 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit Ethernet Controller [8086:105e] (rev 06) Subsystem: Hewlett-Packard Company NC360T PCI Express Dual Port Gigabit Server Adapter [103c:7044] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 58 Region 0: Memory at fdea0000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at fde80000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 5020 [size=32] [virtual] Expansion ROM at f8220000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: e1000e 12:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge [1166:0103] (rev b4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=12, secondary=13, subordinate=16, sec-latency=64 I/O behind bridge: 00006000-00006fff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: 00000000f8300000-00000000f83fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 13:04.0 PCI bridge [0604]: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge [1166:0104] (rev b2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Bus: primary=13, secondary=14, subordinate=16, sec-latency=64 Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 13:08.0 RAID bus controller [0104]: Hewlett-Packard Company Smart Array E200i (SAS Controller) [103c:3238] Subsystem: Hewlett-Packard Company Smart Array E200i [103c:3211] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 56 Region 0: Memory at fdf80000 (64-bit, non-prefetchable) [size=512K] Region 2: I/O ports at 6000 [size=256] Region 3: Memory at fdf70000 (32-bit, non-prefetchable) [size=32K] [virtual] Expansion ROM at f8300000 [disabled] [size=16K] Capabilities: <access denied> Kernel driver in use: cciss ** Sound cards: -- System Information: Debian Release: 6.0.1 APT prefers stable APT policy: (500, 'stable') Architecture: amd64 (x86_64) Kernel: Linux 2.6.32-5-amd64 (SMP w/8 CPU cores) Locale: LANG=es_PY.UTF-8, LC_CTYPE=es_PY.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-5-amd64 depends on: ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs ii linux-base 2.6.32-31 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-amd64 recommends: pn firmware-linux-free <none> (no description available) Versions of packages linux-image-2.6.32-5-amd64 suggests: pn grub | lilo <none> (no description available) pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-amd64 is related to: ii firmware-bnx2 0.28 Binary firmware for Broadcom NetXt pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) pn firmware-linux-nonfree <none> (no description available) pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf-show failed -- §~^Calabaza^~§ from Barrio Obrero, Asunción, Paraguay http://es.wikipedia.org/wiki/Top-posting http://es.wikipedia.org/wiki/Netiquette -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
