hi, On Wed, Aug 17, 2005 at 02:26:17AM +0200, Daniel Ritz wrote: > On Tuesday 16 August 2005 22.47, Philippe Bourcier wrote: > > > > I tried latest debian 2.6.12 kernel; see: > > http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=321419 > > > > irq 11: nobody cared! > > [<c01388fa>] __report_bad_irq+0x2a/0xa0 > > [<c013836d>] handle_IRQ_event+0x3d/0x70 > > [<c0138a12>] note_interrupt+0x82/0xa0 > > [<c0138490>] __do_IRQ+0xf0/0x100 > > [<c0105729>] do_IRQ+0x19/0x30 > > [<c0103ada>] common_interrupt+0x1a/0x20 > > [<c011f2ae>] __do_softirq+0x2e/0xa0 > > [<c011f346>] do_softirq+0x26/0x30 > > [<c010572e>] do_IRQ+0x1e/0x30 > > [<c0103ada>] common_interrupt+0x1a/0x20 > > handlers: > > [<c8cddea0>] (usb_hcd_irq+0x0/0x80 [usbcore]) > > [<c8d00990>] (yenta_interrupt+0x0/0x40 [yenta_socket]) > > [<c8d00990>] (yenta_interrupt+0x0/0x40 [yenta_socket]) > > Disabling IRQ #11 > > eth0: interrupt(s) dropped! > > > > ask more if you need, > > simple question: is that card a multifunction card with ethernet and a > modem?
exactly! > i see from the dmesg that a ttyS2 pops up the same time when the > 3c589 shows up. the problem compared to 2.4 is that the serial interface > is assigned irq 11 when the network card is on irq 9. but on 2.4 both > functions use irq 9 (which is correct). could you try the attached patch? nope : I never compiled a 2.6 kernel. Perhaps somebody of the Debian Kernel Team could help > if the patch doesn't help please give me the output of cbdump and cardctl > ident when the card is inserted and all drivers are loaded. i got http://pcmcia.arm.linux.org.uk/progs/cbdump.c $ cbdump pcilib: sysfs_read: tried to read 4 bytes at 128, but got only 0 pcilib: sysfs_read: tried to read 4 bytes at 140, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 144, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 145, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 146, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 147, but got only 0 open /dev/mem: Permission denied pcilib: sysfs_read: tried to read 4 bytes at 128, but got only 0 pcilib: sysfs_read: tried to read 4 bytes at 140, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 144, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 145, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 146, but got only 0 pcilib: sysfs_read: tried to read 1 bytes at 147, but got only 0 open /dev/mem: Permission denied 00:03.0 CardBus bridge: Texas Instruments PCI1250 -- generic cardbus config registers Vendor ID [00] : 0x104c Device ID [02] : 0xac16 PCI command [04] : 0x0007 Base address [10] : 0x08000000 Memory Base 0 [1c] : 0x08400000 Memory Limit 0 [20] : 0x087ff000 Memory Base 1 [24] : 0x08800000 Memory Limit 1 [28] : 0x08bff000 IO Base 0 [2c] : 0x00004000 IO Limit 0 [30] : 0x000040fc IO Base 1 [34] : 0x00004400 IO Limit 1 [38] : 0x000044fc Bridge control [3e] : 0x05c0 Subsystem vendor ID [40] : 0x0000 Subsystem device ID [42] : 0x0000 Legacy mode base [44] : 0x0001 -- TI specific config registers System control [80] : 0xffffffff IRQ Mux [8c] : 0xffffffff Retry [90] : 0xff Card control [91] : 0xff Device control [92] : 0xff Diagnostic [93] : 0xff 00:03.1 CardBus bridge: Texas Instruments PCI1250 -- generic cardbus config registers Vendor ID [00] : 0x104c Device ID [02] : 0xac16 PCI command [04] : 0x0007 Base address [10] : 0x08001000 Memory Base 0 [1c] : 0x08c00000 Memory Limit 0 [20] : 0x08fff000 Memory Base 1 [24] : 0x09000000 Memory Limit 1 [28] : 0x093ff000 IO Base 0 [2c] : 0x00004800 IO Limit 0 [30] : 0x000048fc IO Base 1 [34] : 0x00004c00 IO Limit 1 [38] : 0x00004cfc Bridge control [3e] : 0x0540 Subsystem vendor ID [40] : 0x0000 Subsystem device ID [42] : 0x0000 Legacy mode base [44] : 0x0001 -- TI specific config registers System control [80] : 0xffffffff IRQ Mux [8c] : 0xffffffff Retry [90] : 0xff Card control [91] : 0xff Device control [92] : 0xff Diagnostic [93] : 0xff $ cadctl ident Socket 0: product info: "Adaptec, Inc.", "APA-1460 SCSI Host Adapter", "Version 0.01" manfid: 0x012f, 0x0002 Socket 1: product info: "3Com", "Megahertz 3CXEM556", "LAN + 56k Modem", "" manfid: 0x0101, 0x0035 function: 0 (multifunction) -- / \ ((__-^^-,-^^-__)) .''`. Philippe BOURCIER `-_---' `---_-' .-. : :' : http://bourcier.philippe.online.fr `--|o` 'o|--' /V\ `. `' \ ` / // \\ `- Linux Counter registered user #290012 ): :( /( )\ :o_o: ^^-^^ "-" -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
