Package: linux-2.6
Version: 2.6.32-12
Severity: normal
Just upgraded from linux-image-2.6.32-3-powerpc64 to this version.
With this version, about 20 seconds after boot, the fan comes on at 100%
fanspeed and remains on in spite of the fact that the machine is under mininal
CPU load.
This did not happen with linux-image-2.6.32-3-powerpc64.
I diffed the /boot/config-* files for the two kernels and there is no obvious
difference there.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-powerpc64 (Debian 2.6.32-12) (b...@decadent.org.uk) (gcc
version 4.3.4 (Debian 4.3.4-10) ) #1 SMP Mon May 3 13:36:05 UTC 2010
** Command line:
root=/dev/sda3 ro
** Not tainted
** Kernel log:
[ 8.365088] udev: starting version 153
[ 9.229930] [drm] Initialized drm 1.1.0 20060810
[ 10.168204] [drm] nouveau 0000:0a:00.0: Detected an NV40 generation card
(0x043100a4)
[ 10.177480] [drm] nouveau 0000:0a:00.0: OF bios successfully copied (6447
bytes)
[ 10.186331] [drm] nouveau 0000:0a:00.0: Attempting to load BIOS image from
PROM
[ 10.195197] [drm] nouveau 0000:0a:00.0: ... BIOS signature not found
[ 10.203977] [drm] nouveau 0000:0a:00.0: Attempting to load BIOS image from
PRAMIN
[ 10.273252] [drm] nouveau 0000:0a:00.0: ... BIOS checksum invalid
[ 10.281950] [drm] nouveau 0000:0a:00.0: Attempting to load BIOS image from
PCIROM
[ 10.290704] [drm] nouveau 0000:0a:00.0: ... BIOS signature not found
[ 10.299355] [drm] nouveau 0000:0a:00.0: Using BIOS image from PRAMIN
[ 10.368229] [drm] nouveau 0000:0a:00.0: BIT BIOS found
[ 10.376835] [drm] nouveau 0000:0a:00.0: Bios version 05.43.02.75
[ 10.385430] [drm] nouveau 0000:0a:00.0: BIT table 'd' not found
[ 10.394046] [drm] nouveau 0000:0a:00.0: Found Display Configuration Block
version 3.0
[ 10.402683] [drm] nouveau 0000:0a:00.0: DCB connector table: VHER 0x30 5 7 2
[ 10.411294] [drm] nouveau 0000:0a:00.0: 0: 0x00001030: type 0x30 idx 0 tag
0x07
[ 10.419915] [drm] nouveau 0000:0a:00.0: 1: 0x00002130: type 0x30 idx 1 tag
0x08
[ 10.428418] [drm] nouveau 0000:0a:00.0: Raw DCB entry 0: 01000100 00000028
[ 10.436931] [drm] nouveau 0000:0a:00.0: Raw DCB entry 1: 03000102 00000000
[ 10.445382] [drm] nouveau 0000:0a:00.0: Raw DCB entry 2: 04011210 00000028
[ 10.453749] [drm] nouveau 0000:0a:00.0: Raw DCB entry 3: 02111212 02000100
[ 10.461998] [drm] nouveau 0000:0a:00.0: Raw DCB entry 4: 02011211 0020c070
[ 10.470199] [drm] nouveau 0000:0a:00.0: Parsing VBIOS init table 0 at offset
0x0744
[ 10.478629] [drm] nouveau 0000:0a:00.0: Parsing VBIOS init table 1 at offset
0x0B87
[ 10.533894] [drm] nouveau 0000:0a:00.0: Parsing VBIOS init table 2 at offset
0x105B
[ 10.542007] [drm] nouveau 0000:0a:00.0: Parsing VBIOS init table 3 at offset
0x1195
[ 10.573700] [drm] nouveau 0000:0a:00.0: Parsing VBIOS init table 4 at offset
0x1273
[ 10.619407] [TTM] Zone kernel: Available graphics memory: 5278766 kiB.
[ 10.627274] [TTM] Zone dma32: Available graphics memory: 2097152 kiB.
[ 10.636596] [drm] nouveau 0000:0a:00.0: 256 MiB VRAM
[ 10.649490] [drm] nouveau 0000:0a:00.0: 64 MiB GART (aperture)
[ 10.657556] [drm] nouveau 0000:0a:00.0: Allocating FIFO number 0
[ 10.668200] [drm] nouveau 0000:0a:00.0: nouveau_channel_alloc: initialised
FIFO 0
[ 10.675853] [drm] nouveau 0000:0a:00.0: Initial CRTC_OWNER is 0
[ 10.683348] [drm] nouveau 0000:0a:00.0: Detected a DVI-I connector
[ 10.692784] [drm] nouveau 0000:0a:00.0: Detected a DVI-I connector
[ 10.702270] irq: irq 28 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 28
[ 10.702300] irq: irq 11 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 25
[ 10.702320] irq: irq 12 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 26
[ 10.702463] irq: irq 30 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 30
[ 10.702483] irq: irq 15 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 29
[ 10.702506] irq: irq 16 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 31
[ 10.702537] [drm] nouveau 0000:0a:00.0: Detected a TV connector
[ 10.711001] [drm] nouveau 0000:0a:00.0: Setting dpms mode 3 on vga encoder
(output 0)
[ 10.717349] [drm] nouveau 0000:0a:00.0: Setting dpms mode 3 on tmds encoder
(output 1)
[ 10.723480] [drm] nouveau 0000:0a:00.0: Setting dpms mode 3 on vga encoder
(output 2)
[ 10.729564] [drm] nouveau 0000:0a:00.0: Setting dpms mode 3 on tmds encoder
(output 3)
[ 10.735586] [drm] nouveau 0000:0a:00.0: Setting dpms mode 3 on TV encoder
(output 4)
[ 10.737966] snd-aoa-fabric-layout: Using PMF GPIOs
[ 10.746085] snd-aoa-codec-onyx: found pcm3052
[ 10.746925] snd-aoa-fabric-layout: platform-onyx-codec-ref doesn't match!
[ 10.752830] snd-aoa: fabric didn't like codec onyx
[ 10.760886] snd-aoa-codec-onyx: found pcm3052
[ 10.761713] snd-aoa-fabric-layout: can use this codec
[ 10.799120] snd-aoa-codec-onyx: attached to onyx codec via i2c
[ 10.804998] irq: irq 79 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 79
[ 10.805035] irq: irq 75 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 75
[ 10.805061] snd-aoa-codec-onyx: created and attached onyx instance
[ 11.001831] [drm] nouveau 0000:0a:00.0: allocated 1280x1024 fb: 0x49000, bo
c000000309d56400
[ 11.007739] fb: conflicting fb hw usage nouveaufb vs OFfb NVDA,Displ -
removing generic driver
[ 11.013772] Console: switching to colour dummy device 80x25
[ 11.013933] Trying to free nonexistent resource
<0000000090020000-000000009019ffff>
[ 11.014312] Console: switching to colour frame buffer device 160x64
[ 11.024645] [drm] nouveau 0000:0a:00.0: Output DVI-I-1 is running on CRTC 0
using output A
[ 11.024651] [drm] nouveau 0000:0a:00.0: 0x14CC: Parsing digital output
script table
[ 11.077710] [drm] nouveau 0000:0a:00.0: Setting dpms mode 0 on tmds encoder
(output 1)
[ 11.077717] [drm] nouveau 0000:0a:00.0: Output DVI-I-1 is running on CRTC 0
using output A
[ 11.078972] fb0: nouveaufb frame buffer device
[ 11.078980] registered panic notifier
[ 11.078995] [drm] Initialized nouveau 0.0.15 20090420 for 0000:0a:00.0 on
minor 0
[ 13.258247] Adding 9974756k swap on /dev/sda4. Priority:-1 extents:1
across:9974756k
[ 13.477012] EXT3 FS on sda3, internal journal
[ 13.615229] loop: module loaded
[ 14.666660] irq: irq 8 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 32
[ 14.695813] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.870619] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[ 17.870645] tg3: eth0: Flow control is on for TX and on for RX.
[ 17.873739] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.311848] fuse init (API version 7.13)
[ 28.030687] eth0: no IPv6 routers present
[ 28.414126] Bluetooth: Core ver 2.15
[ 28.414623] NET: Registered protocol family 31
[ 28.414965] Bluetooth: HCI device and connection manager initialized
[ 28.415311] Bluetooth: HCI socket layer initialized
[ 28.641090] Bluetooth: L2CAP ver 2.14
[ 28.641873] Bluetooth: L2CAP socket layer initialized
[ 28.647649] Bluetooth: RFCOMM TTY layer initialized
[ 28.648103] Bluetooth: RFCOMM socket layer initialized
[ 28.648457] Bluetooth: RFCOMM ver 1.11
[ 28.652177] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 28.652599] Bluetooth: BNEP filters: protocol multicast
[ 28.694865] Bridge firewalling registered
[ 28.833060] Bluetooth: SCO (Voice Link) ver 0.6
[ 28.833959] Bluetooth: SCO socket layer initialized
[ 30.761314] irq: irq 9 on host /u...@0,f8000000/m...@f8040000 mapped to
virtual irq 33
[ 30.813550] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 30.844128] lp: driver loaded but no devices found
[ 34.522661] [drm] nouveau 0000:0a:00.0: Setting dpms mode 1 on tmds encoder
(output 1)
[ 35.802880] [drm] nouveau 0000:0a:00.0: Setting dpms mode 0 on tmds encoder
(output 1)
** Model information
revision : 1.1 (pvr 0044 0101)
revision : 1.1 (pvr 0044 0101)
platform : PowerMac
model : PowerMac11,2
machine : PowerMac11,2
motherboard : PowerMac11,2 MacRISC4 Power Macintosh
** Loaded modules:
Module Size Used by
lp 12220 0
parport 43200 1 lp
sco 14022 2
bridge 67590 0
stp 2328 1 bridge
bnep 15977 2
rfcomm 49864 0
l2cap 40195 4 bnep,rfcomm
crc16 1417 1 l2cap
bluetooth 70531 6 sco,bnep,rfcomm,l2cap
rfkill 23005 3 bluetooth
cpufreq_powersave 1442 0
cpufreq_ondemand 11513 1
cpufreq_stats 5322 0
cpufreq_userspace 3167 0
cpufreq_conservative 8862 0
fuse 78560 1
firewire_sbp2 18321 0
loop 19109 0
snd_aoa_codec_onyx 15255 2
snd_aoa_fabric_layout 13109 1
snd_aoa 17690 2 snd_aoa_codec_onyx,snd_aoa_fabric_layout
snd_aoa_i2sbus 24367 1
snd_aoa_soundbus 5404 2 snd_aoa_fabric_layout,snd_aoa_i2sbus
snd_pcm 96812 1 snd_aoa_i2sbus
snd_page_alloc 8589 1 snd_pcm
joydev 13834 0
snd_seq 70658 0
nouveau 568794 2
snd_timer 26055 2 snd_pcm,snd_seq
snd_seq_device 7666 1 snd_seq
drm_kms_helper 28153 1 nouveau
ttm 65264 1 nouveau
drm 209226 3 nouveau,drm_kms_helper,ttm
snd 83274 10
snd_aoa_codec_onyx,snd_aoa_fabric_layout,snd_aoa,snd_aoa_i2sbus,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 7939 1 snd
evdev 13386 8
ext3 159407 1
jbd 60811 1 ext3
mbcache 8262 1 ext3
usbhid 49249 0
hid 86606 1 usbhid
sd_mod 41767 3
crc_t10dif 1409 1 sd_mod
ide_pci_generic 3551 0
ata_generic 4418 0
ohci_hcd 59536 0
ehci_hcd 73308 0
sata_svw 9431 2
libata 189095 2 ata_generic,sata_svw
firewire_ohci 37836 0
scsi_mod 175857 3 firewire_sbp2,sd_mod,libata
ide_cd_mod 33979 0
cdrom 40045 1 ide_cd_mod
firewire_core 57162 2 firewire_sbp2,firewire_ohci
crc_itu_t 1468 1 firewire_core
usbcore 182816 4 usbhid,ohci_hcd,ehci_hcd
nls_base 8213 1 usbcore
tg3 147498 0
libphy 24555 1 tg3
i2c_powermac 5654 0
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet static
address 192.168.200.110
netmask 255.255.255.0
gateway 192.168.200.99
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:16:cb:39:4f:1a brd ff:ff:ff:ff:ff:ff
inet 192.168.200.110/24 brd 192.168.200.255 scope global eth0
inet6 fe80::216:cbff:fe39:4f1a/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen
1000
link/ether 00:16:cb:39:4f:1b brd ff:ff:ff:ff:ff:ff
4: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether a6:d2:74:96:e5:f7 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 79 1 0 0 0 0 0 0 79
1 0 0 0 0 0 0
eth0: 265606 341 0 0 0 0 0 0 40145
376 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
pan0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
356 total packets received
0 forwarded
0 incoming packets discarded
356 incoming packets delivered
348 requests sent out
Icmp:
1 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 1
1 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 1
IcmpMsg:
InType3: 1
OutType3: 1
Tcp:
14 active connections openings
0 passive connection openings
0 failed connection attempts
0 connection resets received
0 connections established
241 segments received
225 segments send out
4 segments retransmited
0 bad segments received.
1 resets sent
Udp:
114 packets received
0 packets to unknown port received.
0 packet receive errors
116 packets sent
UdpLite:
TcpExt:
2 TCP sockets finished time wait in fast timer
11 delayed acks sent
168 packet headers predicted
29 acknowledgments not containing data payload received
3 predicted acknowledgments
1 congestion windows recovered without slow start after partial ack
3 other TCP timeouts
IpExt:
InMcastPkts: 18
OutMcastPkts: 20
InOctets: 262418
OutOctets: 29728
InMcastOctets: 3055
OutMcastOctets: 3135
*** Device features:
eth0: 0x109a3
eth1: 0x109a3
lo: 0x13865
pan0: 0xff3865
** PCI devices:
0000:00:0b.0 PCI bridge [0604]: Apple Computer Inc. CPC945 PCIe Bridge
[106b:005b] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
I/O behind bridge: 00000000-0000ffff
Memory behind bridge: 90000000-afffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0000:0a:00.0 VGA compatible controller [0300]: nVidia Corporation NV43 [GeForce
6600] [10de:0141] (rev a2) (prog-if 00 [VGA controller])
Subsystem: nVidia Corporation Device [10de:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at a1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at 90000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at a0000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at a2000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nouveau
0001:00:00.0 Host bridge [0600]: Apple Computer Inc. U4 HT Bridge [106b:0074]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
0001:00:01.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-X bridge
[1166:0130] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:02.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-X bridge
[1166:0130] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: fa500000-fa5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:03.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:04.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:05.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=08, subordinate=08, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:06.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=09, subordinate=09, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:07.0 PCI bridge [0604]: Apple Computer Inc. Shasta PCI Bridge
[106b:0053] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: fa000000-fa3fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:08.0 PCI bridge [0604]: Apple Computer Inc. Shasta PCI Bridge
[106b:0054] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:09.0 PCI bridge [0604]: Apple Computer Inc. Shasta PCI Bridge
[106b:0055] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: fa400000-fa4fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:01:07.0 Class [ff00]: Apple Computer Inc. Shasta Mac I/O [106b:004f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 64 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
Kernel driver in use: macio
0001:01:0b.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 70
Region 0: Memory at 80082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
0001:01:0b.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 70
Region 0: Memory at 80081000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
0001:01:0b.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev
04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0 [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 70
Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
0001:03:0c.0 IDE interface [0101]: Broadcom K2 SATA [1166:0240] (prog-if 8f
[Master SecP SecO PriP PriO])
Subsystem: Broadcom K2 SATA [1166:0240]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Interrupt: pin ? routed to IRQ 18
Region 0: I/O ports at <unassigned> [disabled]
Region 1: I/O ports at <unassigned> [disabled]
Region 2: I/O ports at <unassigned> [disabled]
Region 3: I/O ports at <unassigned> [disabled]
Region 4: I/O ports at <unassigned> [disabled]
Region 5: Memory at fa402000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: sata_svw
0001:03:0d.0 Class [ff00]: Apple Computer Inc. Shasta IDE [106b:0050]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 38
Region 0: Memory at fa404000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: ide-pmac
0001:03:0e.0 FireWire (IEEE 1394) [0c00]: Apple Computer Inc. Shasta Firewire
[106b:0052] (prog-if 10 [OHCI])
Subsystem: Apple Computer Inc. Device [106b:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 39
Region 0: Memory at fa400000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
0001:05:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5780
Gigabit Ethernet [14e4:166a] (rev 03)
Subsystem: Apple Computer Inc. Device [106b:0085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at fa530000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fa520000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
0001:05:04.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5780
Gigabit Ethernet [14e4:166a] (rev 03)
Subsystem: Apple Computer Inc. Device [106b:0085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 33
Region 0: Memory at fa510000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fa500000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
** USB devices:
Bus 003 Device 004: ID 046d:c045 Logitech, Inc. Optical Mouse
Bus 003 Device 003: ID 413c:2010 Dell Computer Corp.
Bus 003 Device 002: ID 413c:1003 Dell Computer Corp. Keyboard Hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing')
Architecture: powerpc (ppc64)
Kernel: Linux 2.6.32-5-powerpc64 (SMP w/2 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=ANSI_X3.4-1968)
(ignored: LC_ALL set to POSIX)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-powerpc64 depends on:
ii debconf [debconf-2.0] 1.5.32 Debian configuration management sy
ii initramfs-tools [linux-initr 0.94.4 tools for generating an initramfs
ii libc6 2.10.2-7 Embedded GNU C Library: Shared lib
ii linux-base 2.6.32-12 Linux image base package
ii module-init-tools 3.12~pre2-3 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-powerpc64 recommends:
ii firmware-linux-free 2.6.32-12 Binary firmware for various driver
Versions of packages linux-image-2.6.32-5-powerpc64 suggests:
pn linux-doc-2.6.32 <none> (no description available)
pn mkvmlinuz <none> (no description available)
Versions of packages linux-image-2.6.32-5-powerpc64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.24 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-5-powerpc64/postinst/bootloader-error-2.6.32-5-powerpc64:
linux-image-2.6.32-5-powerpc64/prerm/removing-running-kernel-2.6.32-5-powerpc64:
true
linux-image-2.6.32-5-powerpc64/postinst/bootloader-test-error-2.6.32-5-powerpc64:
linux-image-2.6.32-5-powerpc64/prerm/would-invalidate-boot-loader-2.6.32-5-powerpc64:
true
linux-image-2.6.32-5-powerpc64/postinst/missing-firmware-2.6.32-5-powerpc64:
linux-image-2.6.32-5-powerpc64/postinst/depmod-error-initrd-2.6.32-5-powerpc64:
false
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
