Package: linux-2.6
Version: 2.6.33-1~experimental.4
Severity: normal
linux-image-2.6.32-3-amd64 is fine, but linux-image-2.6.33-2-amd64 from
experimental won't boot.
As I can't see the screen, I'm relying on others to report the error message,
which is approximately as follows.
Kernel panic - unable to mount root fs on unknown-block 0,0
The root file system is XFS, specified as a UUID in /boot/grub/grub.cfg.
I also tried booting with the root=/dev/sda1 kernel parameter, but this
still resulted in a kernel panic with a stack trace that I wasn't able to
capture.
I'm planning to set up network console to obtain traces regarding a CPU clock
frequency issue on an old laptop that I should be in a position to test in the
next week or so, and which is the subject of another outstanding bug report of
mine. If necessary, I can apply the same technique here, although it's my
primary workstation in this instance and unfortunately the only recovery
technique seems to be to power cycle the machine.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: Hewlett-Packard
product_name: HP xw6400 Workstation
product_version:
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: 786D4 v01.23
board_vendor: Hewlett-Packard
board_name: 0A04h
board_version: NA
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5000X Chipset Memory Controller
Hub [8086:25c0] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Capabilities: <access denied>
00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4
Port 2 [8086:25e2] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d5200000-d76fffff
Prefetchable memory behind bridge: 00000000d0200000-00000000d03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4
Port 3 [8086:25e3] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=60, subordinate=60, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:04.0 PCI bridge [0604]: Intel Corporation 5000X Chipset PCI Express x16 Port
4-7 [8086:25fa] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=40, subordinate=40, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: d1000000-d31fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000d01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4
Port 5 [8086:25e5] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=fe, subordinate=fe, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:06.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4
Port 6 [8086:25e6] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=fd, subordinate=fd, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:07.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4
Port 7 [8086:25e7] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=fc, subordinate=fc, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers
[8086:25f0] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: i5000_edac
00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers
[8086:25f0] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers
[8086:25f0] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved
Registers [8086:25f1] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved
Registers [8086:25f3] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers
[8086:25f5] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers
[8086:25f6] (rev 12)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:1b.0 Audio device [0403]: Intel Corporation 631xESB/632xESB High Definition
Audio Controller [8086:269a] (rev 09)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100 Chipset PCI
Express Root Port 1 [8086:2690] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=80, subordinate=80, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #1 [8086:2688] (rev 09) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 3000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #2 [8086:2689] (rev 09) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #3 [8086:268a] (rev 09) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 3040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #4 [8086:268b] (rev 09) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at 3060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset
EHCI USB2 Controller [8086:268c] (rev 09) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0404000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
d9) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: d4000000-d51fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100 Chipset LPC
Interface Controller [8086:2670] (rev 09)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 631xESB/632xESB IDE Controller
[8086:269e] (rev 09) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 30c0 [size=16]
Kernel driver in use: PIIX_IDE
00:1f.2 RAID bus controller [0104]: Intel Corporation 631xESB/632xESB SATA RAID
Controller [8086:2682] (rev 09)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 30e0 [size=8]
Region 1: I/O ports at 30f8 [size=4]
Region 2: I/O ports at 30e8 [size=8]
Region 3: I/O ports at 30fc [size=4]
Region 4: I/O ports at 3080 [size=32]
Region 5: Memory at d0404400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
01:04.0 Multimedia audio controller [0401]: Xilinx Corporation RME Digi9652
(Hammerfall) [10ee:3fc4] (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=16M]
Kernel driver in use: RME Digi9652 (Hammerfall)
10:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express
Upstream Port [8086:3500] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=10, secondary=1e, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d5200000-d59fffff
Prefetchable memory behind bridge: 00000000d0200000-00000000d03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
10:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express to
PCI-X Bridge [8086:350c] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at d7601000 (64-bit, non-prefetchable) [size=4K]
Bus: primary=10, secondary=11, subordinate=1d, sec-latency=32
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
1e:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express
Downstream Port E1 [8086:3510] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=1e, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d5200000-d54fffff
Prefetchable memory behind bridge: 00000000d0200000-00000000d03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
1e:01.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express
Downstream Port E2 [8086:3514] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=1e, secondary=1f, subordinate=1f, sec-latency=0
Memory behind bridge: d5500000-d57fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
1f:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5752
Gigabit Ethernet PCI Express [14e4:1600] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:3014]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 33
Region 0: Memory at d5500000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
20:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic SAS1064ET
PCI-Express Fusion-MPT SAS [1000:0056] (rev 02)
Subsystem: LSI Logic / Symbios Logic Device [1000:3090]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at d5410000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at d5400000 (64-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d0200000 [disabled] [size=2M]
Capabilities: <access denied>
Kernel driver in use: mptsas
40:00.0 VGA compatible controller [0300]: nVidia Corporation G71GL [Quadro FX
3500] [10de:029d] (rev a1) (prog-if 00 [VGA controller])
Subsystem: nVidia Corporation Device [10de:032b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d2000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at 1000 [size=128]
[virtual] Expansion ROM at d0000000 [disabled] [size=128K]
Capabilities: <access denied>
** USB devices:
Bus 005 Device 002: ID 0403:fe72 Future Technology Devices International, Ltd
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:c016 Logitech, Inc. M-UV69a/HP M-UV96 Optical Wheel
Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 051d:0002 American Power Conversion Uninterruptible
Power Supply
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 007: ID 03f0:0324 Hewlett-Packard SK-2885 keyboard
Bus 001 Device 006: ID 1395:0002 Sennheiser Communications
Bus 001 Device 003: ID 0424:2504 Standard Microsystems Corp. USB 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (990, 'unstable'), (500, 'testing'), (500, 'stable'), (1,
'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-3-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.33-2-amd64 depends on:
ii debconf [debconf 1.5.30 Debian configuration management sy
ii initramfs-tools 0.93.4 tools for generating an initramfs
ii linux-base 2.6.33-1~experimental.4 Linux image base package
ii module-init-tool 3.12~pre2-2 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.33-2-amd64 recommends:
ii firmware-linux-f 2.6.33-1~experimental.4 Binary firmware for various driver
Versions of packages linux-image-2.6.33-2-amd64 suggests:
ii grub 0.97-60 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.33 <none> (no description available)
Versions of packages linux-image-2.6.33-2-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.23 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
linux-image-2.6.33-2-amd64/postinst/bootloader-error-2.6.33-2-amd64:
linux-image-2.6.33-2-amd64/postinst/bootloader-test-error-2.6.33-2-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.33-2-amd64/prerm/removing-running-kernel-2.6.33-2-amd64: true
linux-image-2.6.33-2-amd64/postinst/depmod-error-initrd-2.6.33-2-amd64: false
linux-image-2.6.33-2-amd64/prerm/would-invalidate-boot-loader-2.6.33-2-amd64:
true
linux-image-2.6.33-2-amd64/postinst/missing-firmware-2.6.33-2-amd64:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
