Package: smartmontools
Version: 5.39.1+svn3060-1
Severity: minor
In manual of smartctl: If the GLTSD bit is set then ´smartctl -a´ will issue
a warning.
But if SMART attribute autosave if disabled for SATA drive, no any warning
issued in -a or -x output.
Steps to reproduce:
smartctl -S on /dev/sda
smartctl -a /dev/sda >1
smartctl -S off /dv/sda
smartctl -a /dev/hsda >2
diff 1 2
13c13
< Local Time is: Mon Feb 22 07:03:12 2010 MSK
---
> Local Time is: Mon Feb 22 07:03:21 2010 MSK
====== begin of -x output ====
Data about drive:
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K80 series
Device Model: HDS728080PLA380
Serial Number: PFDB32E8U1NLYM
Firmware Version: PF2OA6EA
User Capacity: 82Â 348Â 277Â 760 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 1
Local Time is: Mon Feb 22 07:11:57 2010 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 36) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: (1828) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 31) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always
- 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline
- 0
3 Spin_Up_Time 0x0007 105 105 024 Pre-fail Always
- 195 (Average 184)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always
- 92
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always
- 0
8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline
- 0
9 Power_On_Hours 0x0012 099 099 000 Old_age Always
- 9386
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 92
192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always
- 445
193 Load_Cycle_Count 0x0012 100 100 050 Old_age Always
- 445
194 Temperature_Celsius 0x0002 137 137 000 Old_age Always
- 40 (Lifetime Min/Max 17/47)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always
- 0
General Purpose Logging (GPL) feature set supported
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
GP Log at address 0x03 has 1 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x20 has 1 sectors [Streaming performance log]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 5 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5 [0] occurred at disk power-on lifetime: 9385 hours (391 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 c2 4f 09 00 00 Error: IDNF
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f 09 00 08 21d+07:57:29.200 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 21d+07:57:29.100 SMART READ LOG
b0 00 d1 00 01 00 00 00 c2 4f 01 00 08 21d+07:57:29.000 SMART READ ATTRIBUTE
THRESHOLDS [OBS-4]
b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 21d+07:57:29.000 SMART READ DATA
b0 00 da 00 00 00 00 00 c2 4f 00 00 08 21d+07:57:28.900 SMART RETURN STATUS
Error 4 [3] occurred at disk power-on lifetime: 9385 hours (391 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 c2 4f 09 00 00 Error: IDNF
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f 09 00 08 21d+07:43:58.200 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 21d+07:43:58.100 SMART READ LOG
b0 00 d1 00 01 00 00 00 c2 4f 01 00 08 21d+07:43:58.000 SMART READ ATTRIBUTE
THRESHOLDS [OBS-4]
b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 21d+07:43:57.900 SMART READ DATA
b0 00 da 00 00 00 00 00 c2 4f 00 00 08 21d+07:43:57.900 SMART RETURN STATUS
Error 3 [2] occurred at disk power-on lifetime: 9385 hours (391 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 c2 4f 09 00 00 Error: IDNF
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f 09 00 08 21d+07:43:54.100 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 21d+07:43:54.000 SMART READ LOG
61 00 08 00 00 00 00 00 7a f6 8e 40 08 21d+07:43:54.000 WRITE FPDMA QUEUED
b0 00 d1 00 01 00 00 00 c2 4f 01 00 08 21d+07:43:53.900 SMART READ ATTRIBUTE
THRESHOLDS [OBS-4]
61 00 30 00 00 00 00 00 7a f6 5e 40 08 21d+07:43:53.900 WRITE FPDMA QUEUED
Error 2 [1] occurred at disk power-on lifetime: 9385 hours (391 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 c2 4f 09 00 00 Error: IDNF
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f 09 00 08 21d+07:43:47.800 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 21d+07:43:47.700 SMART READ LOG
b0 00 d1 00 01 00 00 00 c2 4f 01 00 08 21d+07:43:47.600 SMART READ ATTRIBUTE
THRESHOLDS [OBS-4]
b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 21d+07:43:47.500 SMART READ DATA
b0 00 da 00 00 00 00 00 c2 4f 00 00 08 21d+07:43:47.400 SMART RETURN STATUS
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short captive Interrupted (host reset) 40% 9386 -
# 2 Short captive Interrupted (host reset) 40% 9385 -
# 3 Extended offline Completed without error 00% 9384 -
# 4 Extended offline Completed without error 00% 8599 -
# 5 Extended offline Completed without error 00% 8512 -
# 6 Extended offline Completed without error 00% 3269 -
# 7 Extended offline Completed without error 00% 2885 -
# 8 Extended offline Completed without error 00% 2883 -
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Warning: device does not support SCT Commands
SATA Phy Event Counters (GP Log 0x11) not supported
==== end of -x output =====
-- Package-specific info:
Output of /usr/share/bug/smartmontools:
# CONFIG_IDE_TASK_IOCTL is not set
-- System Information:
Debian Release: 5.0.4
APT prefers stable
APT policy: (990, 'stable'), (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash
Versions of packages smartmontools depends on:
ii debianutils 2.30 Miscellaneous utilities specific t
ii libc6 2.10.2-6 Embedded GNU C Library: Shared lib
ii libcap-ng0 0.6.2-4+b1 An alternate posix capabilities li
ii libgcc1 1:4.4.3-2 GCC support library
ii libselinux1 2.0.89-4 SELinux runtime shared libraries
ii libstdc++6 4.4.3-2 The GNU Standard C++ Library v3
ii lsb-base 3.2-20 Linux Standard Base 3.2 init scrip
Versions of packages smartmontools recommends:
ii mailutils [mailx] 1:1.2+dfsg1-4 GNU mailutils utilities for handli
Versions of packages smartmontools suggests:
pn gsmartcontrol <none> (no description available)
pn powersaved <none> (no description available)
ii smart-notifier 0.28-1.1 graphical hard disk health status
-- debconf-show failed
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
