Package: mpt-status Version: 1.2.0-4.2 Severity: important I have four physical disks on two different raid1 volume. mpt-status only lists information about first raid1, while no information is available for second raid.
This is a detail about volume configuration as available in dmesg: [ 18.652028] scsi4 : ioc0: LSISAS1068E B3, FwRev=00192f00h, Ports=1, MaxQ=266, IRQ=16 [ 18.701577] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 9, phy 0, sas_addr 0x1221000000000000 [ 18.726390] scsi 4:0:0:0: Direct-Access ATA ST3500418AS CC37 PQ: 0 ANSI: 5 [ 18.729019] scsi 4:0:0:0: Attached scsi generic sg1 type 0 [ 18.731646] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 1, phy 1, sas_addr 0x1221000001000000 [ 18.735607] scsi 4:0:1:0: Direct-Access ATA ST3500418AS CC37 PQ: 0 ANSI: 5 [ 18.738010] scsi 4:0:1:0: Attached scsi generic sg2 type 0 [ 18.740297] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 8, phy 2, sas_addr 0x1221000002000000 [ 18.743689] scsi 4:0:2:0: Direct-Access ATA ST3500418AS CC37 PQ: 0 ANSI: 5 [ 18.745570] scsi 4:0:2:0: Attached scsi generic sg3 type 0 [ 18.747273] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 3, phy 3, sas_addr 0x1221000003000000 [ 18.750240] scsi 4:0:3:0: Direct-Access ATA ST3500418AS CC37 PQ: 0 ANSI: 5 [ 18.752155] scsi 4:0:3:0: Attached scsi generic sg4 type 0 [ 18.754101] mptsas: ioc0: attaching raid volume, channel 1, id 2 [ 18.755436] scsi 4:1:2:0: Direct-Access Dell VIRTUAL DISK 1028 PQ: 0 ANSI: 5 [ 18.765191] scsi 4:1:2:0: Attached scsi generic sg5 type 0 [ 18.765209] mptsas: ioc0: attaching raid volume, channel 1, id 0 [ 19.018257] scsi 4:1:0:0: Direct-Access Dell VIRTUAL DISK 1028 PQ: 0 ANSI: 5 [ 19.025039] scsi 4:1:0:0: Attached scsi generic sg6 type 0 [ 19.038640] sd 4:1:2:0: [sda] 975699968 512-byte logical blocks: (499 GB/465 GiB) [ 19.038799] sd 4:1:0:0: [sdb] 975699968 512-byte logical blocks: (499 GB/465 GiB) [ 19.039748] sd 4:1:2:0: [sda] Write Protect is off [ 19.039751] sd 4:1:2:0: [sda] Mode Sense: 03 00 00 08 [ 19.039950] sd 4:1:0:0: [sdb] Write Protect is off [ 19.039952] sd 4:1:0:0: [sdb] Mode Sense: 03 00 00 08 [ 19.040513] sd 4:1:2:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 19.040699] sd 4:1:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 19.042820] sda: [ 19.043002] sdb: sdb1 sdb2 [ 19.050894] sd 4:1:0:0: [sdb] Attached SCSI disk [ 19.056951] sda1 sda2 sda3 [ 19.064720] sd 4:1:2:0: [sda] Attached SCSI disk mpt is version 3.04.12 [ 1.075188] Fusion MPT base driver 3.04.12 [ 1.075190] Copyright (c) 1999-2008 LSI Corporation [...] [ 1.136233] Fusion MPT SAS Host driver 3.04.12 [ 1.136268] mptsas 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [...] [ 30.950496] Fusion MPT misc device (ioctl) driver 3.04.12 [ 30.950528] mptctl: Registered with Fusion MPT base driver [ 30.950530] mptctl: /dev/mptctl @ (major,minor=10,220) This log has been made with kernel 2.6.32 from unstable, same problem with mpt 4.18.0 (from LSI site) and kernel 2.6.26 (debian stable). Bye, Giuseppe -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
