Package: linux-image-2.6.30-2-686
Version: 2.6.30-8
Severity: normal
Hi all,
since some weeks ago I've been experiencing that USB devices mounted through
uhci_hcd fail to mount in my system while those mounted through ehci_hcd do
mount flawlessly.
The two specific devices that are failing are: HP DeskJet F380 and a Samsung
SGH-L760V mobile phone. The HP DeskJet F380 only fails when used as scanner,
while it still works as printer without any trouble. The SGH-L760V fails when
used as USB mass storage device (e.g. to access photos taken with its camera)
while it is perfectly recognized by Network Manager as a GSM modem.
Although I notice reportbug sends relevant information from the kernel log,
I send you some snippets I've collected myself; maybe this eases your work.
These are the mounting logs for the devices.
This is the dmesg for a regular USB memory stick that works perfectly:
Dec 2 17:02:52 UGI kernel: [ 9360.772180] usb 1-5: new high speed USB device
using ehci_hcd and address 7
Dec 2 17:02:52 UGI kernel: [ 9360.907568] usb 1-5: New USB device found,
idVendor=054c, idProduct=0243
Dec 2 17:02:52 UGI kernel: [ 9360.907578] usb 1-5: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Dec 2 17:02:52 UGI kernel: [ 9360.907585] usb 1-5: Product: Storage Media
Dec 2 17:02:52 UGI kernel: [ 9360.907591] usb 1-5: Manufacturer: Sony
Dec 2 17:02:52 UGI kernel: [ 9360.907596] usb 1-5: SerialNumber: 1707013014948
Dec 2 17:02:52 UGI kernel: [ 9360.907789] usb 1-5: configuration #1 chosen
from 1 choice
Dec 2 17:02:52 UGI kernel: [ 9360.909374] scsi3 : SCSI emulation for USB Mass
Storage devices
Dec 2 17:02:57 UGI kernel: [ 9365.909937] scsi 3:0:0:0: Direct-Access Sony
Storage Media 0100 PQ: 0 ANSI: 0 CCS
Dec 2 17:02:57 UGI kernel: [ 9365.910883] sd 3:0:0:0: Attached scsi generic
sg2 type 0
Dec 2 17:02:57 UGI kernel: [ 9365.914631] sd 3:0:0:0: [sdb] 2005504 512-byte
hardware sectors: (1.02 GB/979 MiB)
Dec 2 17:02:57 UGI kernel: [ 9365.915621] sd 3:0:0:0: [sdb] Write Protect is
off
Dec 2 17:02:57 UGI kernel: [ 9365.918750] sdb: sdb1
Dec 2 17:02:57 UGI kernel: [ 9365.979946] sd 3:0:0:0: [sdb] Attached SCSI
removable disk
This is the dmesg for the failing HP DeskJet F380:
Dec 2 17:01:54 UGI kernel: [ 9302.652157] usb 3-2: new full speed USB device
using uhci_hcd and address 4
Dec 2 17:01:54 UGI kernel: [ 9302.849199] usb 3-2: New USB device found,
idVendor=03f0, idProduct=5511
Dec 2 17:01:54 UGI kernel: [ 9302.849208] usb 3-2: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Dec 2 17:01:54 UGI kernel: [ 9302.849216] usb 3-2: Product: Deskjet F300 series
Dec 2 17:01:54 UGI kernel: [ 9302.849221] usb 3-2: Manufacturer: HP
Dec 2 17:01:54 UGI kernel: [ 9302.849227] usb 3-2: SerialNumber: CN67EFF27N04KH
Dec 2 17:01:54 UGI kernel: [ 9302.849420] usb 3-2: configuration #1 chosen
from 1 choice
Dec 2 17:01:54 UGI kernel: [ 9302.856220] usblp0: USB Bidirectional printer
dev 4 if 1 alt 0 proto 2 vid 0x03F0 pid 0x5511
And the Samsung SGH-L760:
Dec 2 17:00:40 UGI kernel: [ 9229.160157] usb 4-1: new full speed USB device
using uhci_hcd and address 9
Dec 2 17:00:40 UGI kernel: [ 9229.321233] usb 4-1: New USB device found,
idVendor=04e8, idProduct=5a0f
Dec 2 17:00:40 UGI kernel: [ 9229.321242] usb 4-1: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Dec 2 17:00:40 UGI kernel: [ 9229.321249] usb 4-1: Product: SGH-L760V
Dec 2 17:00:40 UGI kernel: [ 9229.321255] usb 4-1: Manufacturer: SAMSUNG MTP
Device
Dec 2 17:00:40 UGI kernel: [ 9229.321261] usb 4-1: SerialNumber:
A353666023139976
Dec 2 17:00:40 UGI kernel: [ 9229.321452] usb 4-1: configuration #1 chosen
from 1 choice
Hope you can spot what's wrong.
As always, thanks for the great job you all do at the Debian Project!
-- Package-specific info:
** Version:
Linux version 2.6.30-2-686 (Debian 2.6.30-8) (wa...@debian.org) (gcc version
4.3.4 (Debian 4.3.4-3) ) #1 SMP Sat Sep 26 01:16:22 UTC 2009
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.30-2-686
root=UUID=c65bb980-a4ec-4592-8822-c703a65338a6 ro quiet
** Not tainted
** Kernel log:
[31828.684126] usb usb4: Manufacturer: Linux 2.6.30-2-686 uhci_hcd
[31828.684132] usb usb4: SerialNumber: 0000:00:1d.3
[31828.684245] usb usb4: configuration #1 chosen from 1 choice
[31828.684316] hub 4-0:1.0: USB hub found
[31828.684329] hub 4-0:1.0: 2 ports detected
[31828.992100] usb 3-1: new full speed USB device using uhci_hcd and address 2
[31829.148436] usb 3-1: New USB device found, idVendor=04e8, idProduct=5a0f
[31829.148446] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[31829.148453] usb 3-1: Product: SGH-L760V
[31829.148459] usb 3-1: Manufacturer: SAMSUNG MTP Device
[31829.148465] usb 3-1: SerialNumber: A353666023139976
[31829.148667] usb 3-1: configuration #1 chosen from 1 choice
[31848.933846] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[31848.933853] Warning! ehci_hcd should always be loaded before uhci_hcd and
ohci_hcd, not after
[31848.933913] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[31848.933993] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[31848.934002] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[31848.934554] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 5
[31848.938505] ehci_hcd 0000:00:1d.7: debug port 1
[31848.938517] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[31848.938535] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdc444000
[31848.953144] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[31848.953205] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[31848.953213] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[31848.953220] usb usb5: Product: EHCI Host Controller
[31848.953226] usb usb5: Manufacturer: Linux 2.6.30-2-686 ehci_hcd
[31848.953232] usb usb5: SerialNumber: 0000:00:1d.7
[31848.953404] usb usb5: configuration #1 chosen from 1 choice
[31848.953480] hub 5-0:1.0: USB hub found
[31848.953499] hub 5-0:1.0: 8 ports detected
[31849.076155] usb 3-1: USB disconnect, address 2
[31849.560149] usb 3-1: new full speed USB device using uhci_hcd and address 3
[31849.716830] usb 3-1: New USB device found, idVendor=04e8, idProduct=5a0f
[31849.716840] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[31849.716847] usb 3-1: Product: SGH-L760V
[31849.716853] usb 3-1: Manufacturer: SAMSUNG MTP Device
[31849.716859] usb 3-1: SerialNumber: A353666023139976
[31849.717046] usb 3-1: configuration #1 chosen from 1 choice
[31854.528199] usb 3-1: USB disconnect, address 3
[31859.496165] usb 5-5: new high speed USB device using ehci_hcd and address 3
[31859.631642] usb 5-5: New USB device found, idVendor=054c, idProduct=0243
[31859.631652] usb 5-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[31859.631659] usb 5-5: Product: Storage Media
[31859.631665] usb 5-5: Manufacturer: Sony
[31859.631670] usb 5-5: SerialNumber: 1707013014948
[31859.631859] usb 5-5: configuration #1 chosen from 1 choice
[31859.715379] Initializing USB Mass Storage driver...
[31859.715570] scsi2 : SCSI emulation for USB Mass Storage devices
[31859.715741] usbcore: registered new interface driver usb-storage
[31859.715748] USB Mass Storage support registered.
[31859.716316] usb-storage: device found at 3
[31859.716322] usb-storage: waiting for device to settle before scanning
[31864.712507] usb-storage: device scan complete
[31864.713901] scsi 2:0:0:0: Direct-Access Sony Storage Media 0100
PQ: 0 ANSI: 0 CCS
[31864.714800] sd 2:0:0:0: Attached scsi generic sg2 type 0
[31864.717589] sd 2:0:0:0: [sdb] 2005504 512-byte hardware sectors: (1.02
GB/979 MiB)
[31864.718582] sd 2:0:0:0: [sdb] Write Protect is off
[31864.718590] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[31864.718597] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[31864.723161] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[31864.723181] sdb: sdb1
[31864.784512] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[31865.785103] FAT: utf8 is not a recommended IO charset for FAT filesystems,
filesystem will be case sensitive!
[31875.311779] usb 5-5: USB disconnect, address 3
[32097.316184] usb 2-2: new full speed USB device using uhci_hcd and address 2
[32097.515207] usb 2-2: New USB device found, idVendor=03f0, idProduct=5511
[32097.515216] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[32097.515224] usb 2-2: Product: Deskjet F300 series
[32097.515229] usb 2-2: Manufacturer: HP
[32097.515235] usb 2-2: SerialNumber: CN67EFF27N04KH
[32097.515426] usb 2-2: configuration #1 chosen from 1 choice
[32097.522232] usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid
0x03F0 pid 0x5511
[32353.928164] usb 3-1: new full speed USB device using uhci_hcd and address 4
[32354.089210] usb 3-1: New USB device found, idVendor=04e8, idProduct=5a0f
[32354.089219] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[32354.089227] usb 3-1: Product: SGH-L760V
[32354.089232] usb 3-1: Manufacturer: SAMSUNG MTP Device
[32354.089238] usb 3-1: SerialNumber: A353666023139976
[32354.089437] usb 3-1: configuration #1 chosen from 1 choice
[32364.664186] usb 2-2: USB disconnect, address 2
[32364.664910] usblp0: removed
[32460.392130] usb 3-1: USB disconnect, address 4
[33072.648178] usb 3-1: new full speed USB device using uhci_hcd and address 5
[33072.808253] usb 3-1: New USB device found, idVendor=04e8, idProduct=5a0f
[33072.808262] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[33072.808269] usb 3-1: Product: SGH-L760V
[33072.808275] usb 3-1: Manufacturer: SAMSUNG MTP Device
[33072.808281] usb 3-1: SerialNumber: A353666023139976
[33072.808472] usb 3-1: configuration #1 chosen from 1 choice
[33144.872153] usb 3-1: USB disconnect, address 5
[33484.120182] usb 2-2: new full speed USB device using uhci_hcd and address 3
[33484.317242] usb 2-2: New USB device found, idVendor=03f0, idProduct=5511
[33484.317251] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[33484.317259] usb 2-2: Product: Deskjet F300 series
[33484.317264] usb 2-2: Manufacturer: HP
[33484.317270] usb 2-2: SerialNumber: CN67EFF27N04KH
[33484.317460] usb 2-2: configuration #1 chosen from 1 choice
[33484.328279] usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid
0x03F0 pid 0x5511
[33531.504211] usb 2-2: USB disconnect, address 3
[33531.504994] usblp0: removed
** Loaded modules:
Module Size Used by
nls_utf8 1488 0
nls_cp437 5320 0
vfat 8628 0
fat 41452 1 vfat
nls_base 6416 4 nls_utf8,nls_cp437,vfat,fat
usb_storage 48564 0
ehci_hcd 29812 0
uhci_hcd 19136 0
usblp 10604 0
i915 149164 1
drm 137920 2 i915
i2c_algo_bit 4860 1 i915
ppdev 6348 0
lp 8012 0
parport 31144 2 ppdev,lp
sco 8816 2
bridge 39968 0
stp 2112 1 bridge
bnep 10860 2
rfcomm 30340 0
l2cap 18088 4 bnep,rfcomm
bluetooth 47028 6 sco,bnep,rfcomm,l2cap
acpi_cpufreq 7640 0
cpufreq_userspace 2768 0
cpufreq_powersave 1292 0
cpufreq_stats 3520 0
cpufreq_conservative 6256 0
binfmt_misc 7120 1
ipt_REJECT 2496 1
ipt_LOG 4540 5
xt_limit 2020 7
xt_tcpudp 2508 7
xt_state 1768 7
ipt_addrtype 2048 4
ip6table_filter 3084 1
ip6_tables 11316 1 ip6table_filter
nf_nat_irc 1924 0
nf_conntrack_irc 4972 1 nf_nat_irc
nf_nat_ftp 2380 0
nf_nat 16192 2 nf_nat_irc,nf_nat_ftp
nf_conntrack_ipv4 11928 9 nf_nat
nf_defrag_ipv4 1664 1 nf_conntrack_ipv4
nf_conntrack_ftp 6680 1 nf_nat_ftp
nf_conntrack 57924 7
xt_state,nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_nat,nf_conntrack_ipv4,nf_conntrack_ftp
iptable_filter 2956 1
ip_tables 10188 1 iptable_filter
x_tables 14108 8
ipt_REJECT,ipt_LOG,xt_limit,xt_tcpudp,xt_state,ipt_addrtype,ip6_tables,ip_tables
loop 13324 0
firewire_sbp2 12700 0
snd_hda_codec_realtek 178564 1
snd_hda_intel 22192 2
snd_hda_codec 63580 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 6120 1 snd_hda_codec
snd_pcm_oss 32228 0
snd_mixer_oss 12368 1 snd_pcm_oss
snd_pcm 62396 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_midi 5688 0
snd_rawmidi 18596 1 snd_seq_midi
arc4 1560 2
pcmcia 24280 0
snd_seq_midi_event 6212 1 snd_seq_midi
ecb 2368 2
snd_seq 42436 2 snd_seq_midi,snd_seq_midi_event
snd_timer 17436 2 snd_pcm,snd_seq
snd_seq_device 6136 3 snd_seq_midi,snd_rawmidi,snd_seq
iwl3945 60860 0
iwlcore 92372 1 iwl3945
snd 49060 15
snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
rfkill 9668 2 iwlcore
yenta_socket 21168 1
joydev 8676 0
rsrc_nonstatic 9664 1 yenta_socket
mac80211 142984 2 iwl3945,iwlcore
soundcore 6184 1 snd
i2c_i801 8580 0
serio_raw 4560 0
i2c_core 20844 4 i915,drm,i2c_algo_bit,i2c_i801
evdev 8028 16
pcmcia_core 31212 3 pcmcia,yenta_socket,rsrc_nonstatic
snd_page_alloc 8180 2 snd_hda_intel,snd_pcm
rng_core 3672 0
pcspkr 2104 0
psmouse 37528 0
ac 2960 0
battery 6012 0
container 3244 0
cfg80211 55572 3 iwl3945,iwlcore,mac80211
processor 34560 3 acpi_cpufreq
button 5060 0
ext3 107172 2
jbd 41036 1 ext3
mbcache 6924 1 ext3
sg 20320 0
sd_mod 28740 4
crc_t10dif 1632 1 sd_mod
sr_mod 13264 0
cdrom 30316 1 sr_mod
ata_generic 4340 0
ide_pci_generic 3632 0
ide_core 87940 1 ide_pci_generic
ata_piix 20848 3
sdhci_pci 6540 0
sdhci 14868 1 sdhci_pci
mmc_core 46380 1 sdhci
led_class 3852 3 iwl3945,iwlcore,sdhci
libata 151044 2 ata_generic,ata_piix
firewire_ohci 18952 0
firewire_core 37736 2 firewire_sbp2,firewire_ohci
crc_itu_t 2148 1 firewire_core
usbcore 126052 5 usb_storage,ehci_hcd,uhci_hcd,usblp
r8169 27692 0
mii 4664 1 r8169
scsi_mod 131800 6
usb_storage,firewire_sbp2,sg,sd_mod,sr_mod,libata
intel_agp 23052 1
agpgart 30836 3 drm,intel_agp
video 18044 1 i915
output 2604 1 video
thermal 12580 0
fan 4044 0
thermal_sys 13140 4 processor,video,thermal,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML
and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS,
943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-if
00 [VGA controller])
Subsystem: Toshiba America Info Systems Device [1179:ff01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dc100000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 1800 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at dc200000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME,
943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Toshiba America Info Systems Device [1179:ff01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at dc180000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller [8086:27d8] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at dc440000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d6000000-d7ffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: 00000000d2000000-00000000d3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: da000000-dbffffff
Prefetchable memory behind bridge: 00000000d4000000-00000000d5ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at dc444000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=0a, sec-latency=32
I/O behind bridge: 00005000-00005fff
Memory behind bridge: dc000000-dc0fffff
Prefetchable memory behind bridge: 0000000050000000-0000000053ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge [8086:27b9] (rev 02)
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA
IDE Controller [8086:27c4] (rev 02) (prog-if 80 [Master])
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 18b0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller
[8086:27da] (rev 02)
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18c0 [size=32]
Kernel driver in use: i801_smbus
04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG
[Golan] Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation Device [8086:1041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: iwl3945
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 01)
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: I/O ports at 4000 [size=256]
Region 2: Memory at da000000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at d4000000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
06:00.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306 Fire II IEEE
1394 OHCI Link Layer Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Device [1179:ff00]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at dc001000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at 5000 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
06:04.0 CardBus bridge [0607]: ENE Technology Inc CB-712/4 Cardbus Controller
[1524:1412] (rev 10)
Subsystem: Toshiba America Info Systems Device [1179:ff01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 50000000-53fff000 (prefetchable)
Memory window 1: 54000000-57fff000
I/O window 0: 00005400-000054ff
I/O window 1: 00005800-000058ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
06:04.1 FLASH memory [0501]: ENE Technology Inc ENE PCI Memory Stick Card
Reader Controller [1524:0530] (rev 01)
Subsystem: Toshiba America Info Systems Device [1179:ff01]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at dc001800 (32-bit, non-prefetchable) [size=128]
Capabilities: <access denied>
06:04.2 SD Host controller [0805]: ENE Technology Inc ENE PCI Secure Digital
Card Reader Controller [1524:0550] (rev 01) (prog-if 01)
Subsystem: Toshiba America Info Systems Device [1179:ff02]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 18000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at dc001c00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
06:04.3 FLASH memory [0501]: ENE Technology Inc FLASH memory: ENE Technology
Inc: [1524:0520] (rev 01)
Subsystem: Toshiba America Info Systems Device [1179:ff01]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at dc002000 (32-bit, non-prefetchable) [size=128]
Capabilities: <access denied>
06:04.4 FLASH memory [0501]: ENE Technology Inc SD/MMC Card Reader Controller
[1524:0551] (rev 01)
Subsystem: Toshiba America Info Systems Device [1179:ff02]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at dc001900 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.30-2-686 (SMP w/2 CPU cores)
Locale: LANG=es_AR.UTF-8, LC_CTYPE=es_AR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.30-2-686 depends on:
ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.30-2-686 recommends:
ii libc6-i686 2.10.2-2 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.30-2-686 suggests:
ii grub 0.97-59 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.30 <none> (no description available)
-- debconf information:
linux-image-2.6.30-2-686/postinst/bootloader-test-error-2.6.30-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.30-2-686/preinst/failed-to-move-modules-2.6.30-2-686:
linux-image-2.6.30-2-686/preinst/lilo-initrd-2.6.30-2-686: true
linux-image-2.6.30-2-686/postinst/old-dir-initrd-link-2.6.30-2-686: true
linux-image-2.6.30-2-686/preinst/initrd-2.6.30-2-686:
linux-image-2.6.30-2-686/preinst/elilo-initrd-2.6.30-2-686: true
linux-image-2.6.30-2-686/postinst/depmod-error-2.6.30-2-686: false
linux-image-2.6.30-2-686/postinst/old-initrd-link-2.6.30-2-686: true
linux-image-2.6.30-2-686/preinst/abort-install-2.6.30-2-686:
linux-image-2.6.30-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.30-2-686/preinst/bootloader-initrd-2.6.30-2-686: true
linux-image-2.6.30-2-686/postinst/bootloader-error-2.6.30-2-686:
linux-image-2.6.30-2-686/prerm/removing-running-kernel-2.6.30-2-686: true
linux-image-2.6.30-2-686/preinst/overwriting-modules-2.6.30-2-686: true
linux-image-2.6.30-2-686/preinst/abort-overwrite-2.6.30-2-686:
linux-image-2.6.30-2-686/postinst/depmod-error-initrd-2.6.30-2-686: false
linux-image-2.6.30-2-686/postinst/create-kimage-link-2.6.30-2-686: true
linux-image-2.6.30-2-686/prerm/would-invalidate-boot-loader-2.6.30-2-686: true
linux-image-2.6.30-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.30-2-686/postinst/old-system-map-link-2.6.30-2-686: true
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
