Package: linux-image-2.6.26-2-amd64
Version: 2.6.26-19lenny1
Severity: important
I'm using an Asus A8V motherboard, which has an onboard VIA VT8233/A/8235/8237
AC97 Audio Controller (not sure, just
picket it from lspci). I updated my kernel to 2.6.30-bpo.2-amd64, from
lenny-backports, so I could have ext4 support
for my fresh hard disk drive; but after the update, any audio was barely
audible, even after raising the volume with
alsamixer. The problem is also present in version 2.6.30-2-amd64 from the
testing repository. I'mt back to the
previous 2.6.26-2 kernel at the moment, but I can easily reproduce the steps if
needed. Regards.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-amd64 (Debian 2.6.26-19lenny1) (da...@debian.org) (gcc
version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Mon Oct 19
02:34:17 UTC 2009
** Command line:
root=/dev/sda1 ro
** Tainted: P (1)
** Kernel log:
[ 12.908249] usb usb5: Product: EHCI Host Controller
[ 12.908317] usb usb5: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd
[ 12.908387] usb usb5: SerialNumber: 0000:00:10.4
[ 12.927957] hdc: max request size: 512KiB
[ 12.928391] hdc: 156368016 sectors (80060 MB) w/2048KiB Cache,
CHS=16383/255/63
[ 12.929175] hdc: cache flushes supported
[ 12.929294] hdc: hdc1
[ 13.276191] PM: Starting manual resume from disk
[ 13.329628] kjournald starting. Commit interval 5 seconds
[ 13.329707] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.928018] usb 5-7: new high speed USB device using ehci_hcd and address 3
[ 14.062218] usb 5-7: configuration #1 chosen from 1 choice
[ 14.063018] usb 5-7: New USB device found, idVendor=0dda, idProduct=2026
[ 14.063087] usb 5-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 14.063156] usb 5-7: Product: USB2.0 Card Reader
[ 14.063223] usb 5-7: Manufacturer: Generic
[ 14.063289] usb 5-7: SerialNumber: 0000001
[ 14.484017] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 14.651786] usb 2-2: configuration #1 chosen from 1 choice
[ 14.655867] usb 2-2: New USB device found, idVendor=04d9, idProduct=1400
[ 14.655936] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 14.817527] udev: starting version 141
[ 14.817614] udev: deprecated sysfs layout; update the kernel or disable
CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
[ 14.896017] usb 4-2: new low speed USB device using uhci_hcd and address 2
[ 15.050725] usb 4-2: configuration #1 chosen from 1 choice
[ 15.053803] usb 4-2: New USB device found, idVendor=062a, idProduct=0000
[ 15.053876] usb 4-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 16.051157] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 16.060448] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.159151] input: Power Button (FF) as /class/input/input1
[ 16.184072] ACPI: Power Button (FF) [PWRF]
[ 16.184233] input: Power Button (CM) as /class/input/input2
[ 16.217179] ACPI: Power Button (CM) [PWRB]
[ 16.217325] input: Sleep Button (CM) as /class/input/input3
[ 16.246479] ACPI: Sleep Button (CM) [SLPB]
[ 16.771667] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) ->
IRQ 19
[ 16.859177] usbcore: registered new interface driver hiddev
[ 16.891057] input: HID 04d9:1400 as /class/input/input4
[ 16.891474] phy0: Selected rate control algorithm 'pid'
[ 16.916074] input,hidraw0: USB HID v1.10 Keyboard [HID 04d9:1400] on
usb-0000:00:10.1-2
[ 16.964985] input: HID 04d9:1400 as /class/input/input5
[ 17.008054] input,hidraw1: USB HID v1.10 Mouse [HID 04d9:1400] on
usb-0000:00:10.1-2
[ 17.021710] input: HID 062a:0000 as /class/input/input6
[ 17.052095] input,hidraw2: USB HID v1.10 Mouse [HID 062a:0000] on
usb-0000:00:10.3-2
[ 17.052401] usbcore: registered new interface driver usbhid
[ 17.052471] usbhid: v2.6:USB HID core driver
[ 17.149745] Initializing USB Mass Storage driver...
[ 17.149890] scsi2 : SCSI emulation for USB Mass Storage devices
[ 17.150039] usbcore: registered new interface driver usb-storage
[ 17.150111] USB Mass Storage support registered.
[ 17.180980] usb-storage: device found at 3
[ 17.180984] usb-storage: waiting for device to settle before scanning
[ 17.388339] phy0: hwaddr 00:08:54:93:59:44, RTL8185vD + rtl8225z2
[ 17.657427] input: PC Speaker as /class/input/input7
[ 17.934701] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) ->
IRQ 22
[ 17.935187] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 18.515061] VIA 82xx Modem 0000:00:11.6: enabling device (0000 -> 0001)
[ 18.515136] ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) ->
IRQ 22
[ 19.264014] PCI: Setting latency timer of device 0000:00:11.6 to 64
[ 19.768218] ACPI: PCI interrupt for device 0000:00:11.6 disabled
[ 19.768306] VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
[ 20.714843] Adding 1951856k swap on /dev/sda5. Priority:-1 extents:1
across:1951856k
[ 21.163898] EXT3 FS on sda1, internal journal
[ 21.828437] fuse init (API version 7.9)
[ 21.862429] loop: module loaded
[ 21.917914] device-mapper: uevent: version 1.0.3
[ 21.918038] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised:
dm-de...@redhat.com
[ 22.180175] usb-storage: device scan complete
[ 22.181404] scsi 2:0:0:0: Direct-Access Generic IC1210 CF 1.9C
PQ: 0 ANSI: 0 CCS
[ 22.182646] scsi 2:0:0:1: Direct-Access Generic IC1210 MS 1.9C
PQ: 0 ANSI: 0 CCS
[ 22.183894] scsi 2:0:0:2: Direct-Access Generic IC1210 MMC/SD 1.9C
PQ: 0 ANSI: 0 CCS
[ 22.185150] scsi 2:0:0:3: Direct-Access Generic IC1210 SM 1.9C
PQ: 0 ANSI: 0 CCS
[ 22.197760] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 22.204168] sd 2:0:0:1: [sdd] Attached SCSI removable disk
[ 22.212356] sd 2:0:0:2: [sde] Attached SCSI removable disk
[ 22.220168] sd 2:0:0:3: [sdf] Attached SCSI removable disk
[ 22.924003] kjournald starting. Commit interval 5 seconds
[ 22.924003] EXT3 FS on sda6, internal journal
[ 22.924003] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.157079] eth1: Link changed: 100Mbps, full duplex
[ 29.569529] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+
processors (1 cpu cores) (version 2.20.00)
[ 29.570511] powernow-k8: BIOS error - no PSB or ACPI _PSS objects
[ 31.033939] usbcore: registered new interface driver usblp
[ 31.459827] pnp: the driver 'parport_pc' has been registered
[ 31.460464] lp: driver loaded but no devices found
[ 31.534126] ppdev: user-space parallel port driver
[ 95.385245] NET: Registered protocol family 10
[ 95.385904] lo: Disabled Privacy Extensions
[ 105.752007] eth1: no IPv6 routers present
[ 337.896881] nvidia: module license 'NVIDIA' taints kernel.
[ 338.156283] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 338.156511] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 173.14.20 Thu
Jun 25 18:15:32 PDT 2009
[ 385.647669] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 173.14.20 Thu
Jun 25 18:15:32 PDT 2009
[ 385.798282] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 385.798299] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 385.798401] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[ 5237.174252] ACPI: PCI interrupt for device 0000:00:11.5 disabled
[ 5237.202433] gameport: kgameportd exiting
[ 5269.145901] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) ->
IRQ 22
[ 5269.145958] PCI: Setting latency timer of device 0000:00:11.5 to 64
** Loaded modules:
Module Size Used by
snd_via82xx 28712 0
gameport 17040 1 snd_via82xx
snd_ac97_codec 115416 1 snd_via82xx
ac97_bus 6272 1 snd_ac97_codec
snd_pcm_oss 41760 0
snd_mixer_oss 18816 1 snd_pcm_oss
snd_pcm 81800 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 13072 2 snd_via82xx,snd_pcm
snd_mpu401_uart 11776 1 snd_via82xx
snd_seq_dummy 7428 0
snd_seq_oss 33152 0
snd_seq_midi 11072 0
snd_rawmidi 26784 2 snd_mpu401_uart,snd_seq_midi
snd_seq_midi_event 11904 2 snd_seq_oss,snd_seq_midi
snd_seq 54304 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 25744 2 snd_pcm,snd_seq
snd_seq_device 11668 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 63688 11
snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 12064 1 snd
nvidia 8096240 24
ipv6 288456 10
battery 16904 0
ppdev 11656 0
parport_pc 31016 0
lp 14724 0
parport 41776 3 ppdev,parport_pc,lp
usblp 16896 0
cpufreq_userspace 8452 0
cpufreq_ondemand 11792 0
cpufreq_conservative 11784 0
cpufreq_powersave 6400 0
cpufreq_stats 9120 0
freq_table 9344 2 cpufreq_ondemand,cpufreq_stats
dm_snapshot 19400 0
dm_mirror 20608 0
dm_log 13956 1 dm_mirror
dm_mod 58864 3 dm_snapshot,dm_mirror,dm_log
loop 19468 0
fuse 53184 3
psmouse 42268 0
serio_raw 9988 0
pcspkr 7040 0
k8temp 9216 0
arc4 6272 2
i2c_viapro 12440 0
i2c_core 27936 2 nvidia,i2c_viapro
usb_storage 95936 0
ecb 7296 2
crypto_blkcipher 21636 1 ecb
usbhid 45792 0
hid 41792 1 usbhid
ff_memless 9224 1 usbhid
rtl8180 33664 0
mac80211 162992 1 rtl8180
eeprom_93cx6 6784 1 rtl8180
cfg80211 30224 2 rtl8180,mac80211
button 11680 0
shpchp 34208 0
pci_hotplug 32056 1 shpchp
evdev 14208 5
ext3 125072 2
jbd 51240 1 ext3
mbcache 12804 1 ext3
ide_disk 16512 2
ata_generic 10116 0
ide_pci_generic 9220 0 [permanent]
sd_mod 29376 4
ehci_hcd 36108 0
uhci_hcd 25760 0
via82cxxx 12164 0 [permanent]
ide_core 128284 3 ide_disk,ide_pci_generic,via82cxxx
sata_via 13060 3
libata 165600 2 ata_generic,sata_via
scsi_mod 161016 3 usb_storage,sd_mod,libata
dock 14112 1 libata
sundance 23904 0
mii 9856 1 sundance
skge 41744 0
thermal 22688 0
processor 42304 1 thermal
fan 9352 0
thermal_sys 17728 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. K8T800Pro Host Bridge
[1106:0282]
Subsystem: ASUSTeK Computer Inc. A8V Deluxe [1043:80a3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+ INTx-
Latency: 64
Region 0: Memory at <ignored> (32-bit, prefetchable)
Capabilities: <access denied>
Kernel driver in use: agpgart-amd64
00:00.1 Host bridge [0600]: VIA Technologies, Inc. K8T800Pro Host Bridge
[1106:1282]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.2 Host bridge [0600]: VIA Technologies, Inc. K8T800Pro Host Bridge
[1106:2282]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 Host bridge [0600]: VIA Technologies, Inc. K8T800Pro Host Bridge
[1106:3282]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.4 Host bridge [0600]: VIA Technologies, Inc. K8T800Pro Host Bridge
[1106:4282]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.7 Host bridge [0600]: VIA Technologies, Inc. K8T800Pro Host Bridge
[1106:7282]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237 PCI bridge
[K8T800/K8T890 South] [1106:b188] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: faf00000-fbffffff
Prefetchable memory behind bridge: f0000000-f9ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:0a.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001
Gigabit Ethernet Controller [11ab:4320] (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet
Controller (Asus) [1043:811a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fa800000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at 8400 [size=256]
Expansion ROM at fa700000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: skge
Kernel modules: skge
00:0c.0 Ethernet controller [0200]: Sundance Technology Inc / IC Plus Corp IC
Plus IP100A Integrated 10/100 Ethernet MAC + PHY [13f0:0200] (rev 31)
Subsystem: Sundance Technology Inc / IC Plus Corp Device [13f0:0201]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort+
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 8800 [size=128]
Region 1: Memory at faa00000 (32-bit, non-prefetchable) [size=512]
Expansion ROM at fa900000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: sundance
Kernel modules: sundance
00:0d.0 RAID bus controller [0104]: VIA Technologies, Inc. Device [1106:3241]
(rev 50)
Subsystem: VIA Technologies, Inc. Device [1106:3241]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 64
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at a800 [size=16]
Region 1: I/O ports at a400 [size=16]
Region 2: I/O ports at a000 [size=16]
Region 3: I/O ports at 9800 [size=16]
Region 4: I/O ports at 9400 [size=32]
Region 5: I/O ports at 9000 [size=256]
Expansion ROM at 50000000 [disabled] [size=64K]
Capabilities: <access denied>
00:0e.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185
IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g
Wireless LAN Controller [10ec:8185]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at b000 [size=256]
Region 1: Memory at fac00000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: rtl8180
Kernel modules: rtl8180
00:0f.0 RAID bus controller [0104]: VIA Technologies, Inc. VIA VT6420 SATA RAID
Controller [1106:3149] (rev 80)
Subsystem: ASUSTeK Computer Inc. A7V600/K8V Deluxe/K8V-X/A8V Deluxe
motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at d000 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c400 [size=8]
Region 3: I/O ports at c000 [size=4]
Region 4: I/O ports at b800 [size=16]
Region 5: I/O ports at b400 [size=256]
Capabilities: <access denied>
Kernel driver in use: sata_via
Kernel modules: sata_via
00:0f.1 IDE interface [0101]: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
[1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 20
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: <access denied>
Kernel driver in use: VIA_IDE
Kernel modules: via82cxxx, ide-pci-generic, ata_generic
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
[1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at d400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
[1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at d800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
[1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
[1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev
86) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
[1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fae00000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge
[KT600/K8T800/K8T890 South] [1106:3227]
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
[1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: i2c-viapro
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 60)
Subsystem: ASUSTeK Computer Inc. A8V Deluxe motherboard (Realtek ALC850
codec) [1043:812a]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 22
Region 0: I/O ports at e800 [size=256]
Capabilities: <access denied>
Kernel driver in use: VIA 82xx Audio
Kernel modules: snd-via82xx
00:11.6 Communication controller [0780]: VIA Technologies, Inc. AC'97 Modem
Controller [1106:3068] (rev 80)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 22
Region 0: I/O ports at 1000 [size=256]
Capabilities: <access denied>
Kernel modules: snd-via82xx-modem
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV34 [GeForce FX
5200] [10de:0322] (rev a1) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at faf00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
-- System Information:
Debian Release: 5.0.3
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-2-amd64 (SMP w/1 CPU core)
Locale: LANG=pt_BR.UTF-8, LC_CTYPE=pt_BR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-2-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-2-amd64 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-amd64/postinst/depmod-error-2.6.26-2-amd64: false
linux-image-2.6.26-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-amd64/preinst/abort-install-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/postinst/old-initrd-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/depmod-error-initrd-2.6.26-2-amd64: false
linux-image-2.6.26-2-amd64/postinst/bootloader-test-error-2.6.26-2-amd64:
* linux-image-2.6.26-2-amd64/preinst/overwriting-modules-2.6.26-2-amd64: false
linux-image-2.6.26-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-amd64/prerm/would-invalidate-boot-loader-2.6.26-2-amd64:
true
linux-image-2.6.26-2-amd64/postinst/old-system-map-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/abort-overwrite-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/elilo-initrd-2.6.26-2-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-amd64/postinst/bootloader-error-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/lilo-initrd-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/old-dir-initrd-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/create-kimage-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/initrd-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/failed-to-move-modules-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/bootloader-initrd-2.6.26-2-amd64: true
* linux-image-2.6.26-2-amd64/prerm/removing-running-kernel-2.6.26-2-amd64: false
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
