Package: linux-image-2.6.30-2-amd64
Version: 2.6.30-8
Severity: normal
With the ethernet device on this laptop (Lenovo ideapad u350) the tg3
driver it needs doesn't actually work unless the broadcom module is
loaded first to provide the PHY. However because this is only true for
some tg3-driven devices (I understand) it is not a dependency. The
result is that the kernel duly loads tg3 and the user gets no ethernet.
The workaround is to do this:
add tg3 to /etc/modprobe.d/blacklist
run update-initramfs to copy that into the initramfs to prevent early
loading of tg3.
Add tg3 to /etc/modules so it gets explicitly loaded later
Add /etc/modprobe.d/tg3.conf containing:
install tg3 /sbin/modprobe broadcom; /sbin/modprobe --ignore-install tg3
so that when it is explictly loaded it forces a load of braodcom first.
This has taken me a couple of frustrating hours to work out and some
way of making it 'just work' is needed.
When using debian-installer the problem is worse because the broadcom
module is not even present in the d-i rootfs (presumably because the
module deps say it#s not needed) so you can't even manually get your
network working, and thus have to do an offline base-install then
install a real full kernel package.
If loading the broadcom module doesn't do any harm when it is not
needed then just loading it anyway as explicit dep would be good. If
not then some other way of making sure it gets loaded before tg3, when
required, is needed.
-- Package-specific info:
** Version:
Linux version 2.6.30-2-amd64 (Debian 2.6.30-8) (wa...@debian.org) (gcc version
4.3.4 (Debian 4.3.4-3) ) #1 SMP Fri Sep 25 22:16:56 UTC 2009
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.30-2-amd64
root=UUID=26115ad8-956a-4542-9126-1747351cdb7e ro quiet
** Not tainted
** Kernel log:
[ 1.485042] ACPI Warning (nspredef-0943): \_SB_.PCI0.SAT0.PRT0._GTF: Return
type mismatch - found Integer, expected Buffer [20090320]
[ 1.485052] ata1.00: _GTF unexpected object type 0x1
[ 1.534546] ata1.00: ATA-8: WDC WD1600BEVT-22ZCT0, 11.01A11, max UDMA/133
[ 1.534551] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.536050] ata1.00: _GTF unexpected object type 0x1
[ 1.536197] ata1.00: configured for UDMA/133
[ 1.552138] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVT-2 11.0
PQ: 0 ANSI: 5
[ 1.872021] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.208023] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.544020] ata6: SATA link down (SStatus 0 SControl 300)
[ 2.569082] Driver 'sd' needs updating - please use bus_type methods
[ 2.569227] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160
GB/149 GiB)
[ 2.569248] sd 0:0:0:0: [sda] Write Protect is off
[ 2.569252] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.569285] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 2.569410] sda: sda1 sda2 sda3
[ 2.630250] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.927557] PM: Starting manual resume from disk
[ 2.988554] kjournald starting. Commit interval 5 seconds
[ 2.988566] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.219370] udev: starting version 146
[ 4.402567] ACPI: WMI: Mapper loaded
[ 4.439088] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 4.439097] ACPI: Power Button [PWRF]
[ 4.439204] input: Lid Switch as
/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 4.448489] ACPI: Lid Switch [LID]
[ 4.449051] ACPI Warning (processor_throttling-0844): Invalid throttling
state, reset [20090320]
[ 4.450987] ACPI: AC Adapter [ACAD] (on-line)
[ 4.451099] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 4.451107] ACPI: Power Button [PWRB]
[ 4.451176] input: Sleep Button as
/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[ 4.451182] ACPI: Sleep Button [SLPB]
[ 4.482894] Monitor-Mwait will be used to enter C-1 state
[ 4.482933] Monitor-Mwait will be used to enter C-2 state
[ 4.482944] Marking TSC unstable due to TSC halts in idle
[ 4.483094] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 4.483146] processor ACPI_CPU:00: registered as cooling_device0
[ 4.483153] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 4.519655] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 5.100435] ACPI: Battery Slot [BAT1] (battery present)
[ 5.119169] Linux video capture interface: v2.00
[ 5.127028] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (090c:37a9)
[ 5.128176] input: Lenovo EasyCamera as
/devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5:1.0/input/input7
[ 5.128244] usbcore: registered new interface driver uvcvideo
[ 5.128248] USB Video Class driver (v0.1.0)
[ 5.199215] Error: Driver 'pcspkr' is already registered, aborting...
[ 5.214433] cfg80211: Using static regulatory domain info
[ 5.214437] cfg80211: Regulatory domain: US
[ 5.214440] (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 5.214445] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 5.214449] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.214453] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.214457] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.214462] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.214466] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 5.214477] cfg80211: Calling CRDA for country: US
[ 5.287678] alloc irq_desc for 22 on cpu 0 node 0
[ 5.287683] alloc kstat_irqs on cpu 0 node 0
[ 5.287693] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ
22
[ 5.287744] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 5.375591] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 5.403028] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ
19
[ 5.416906] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 6, Type 5,
Revision 1)
[ 5.417241] b43: probe of ssb0:0 failed with error -95
[ 5.417270] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[ 5.434705] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps:
0xd04731/0xa40000
[ 5.490102] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio4/input/input8
[ 5.500029] Clocksource tsc unstable (delta = -70821955 ns)
[ 6.045726] Adding 3903784k swap on /dev/sda2. Priority:-1 extents:1
across:3903784k
[ 6.298696] EXT3 FS on sda1, internal journal
[ 6.452690] loop: module loaded
[ 6.544619] tg3.c:v3.98 (February 25, 2009)
[ 6.544673] tg3 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 6.544687] tg3 0000:08:00.0: setting latency timer to 64
[ 6.552162] tg3 0000:08:00.0: PME# disabled
[ 6.552778] tg3 mdio bus: probed
[ 7.361390] eth0: Tigon3 [partno(none) rev 57780001] (PCI Express) MAC
address 00:23:8b:fc:3e:db
[ 7.361395] eth0: attached PHY driver [Broadcom BCM57780]
(mii_bus:phy_addr=800:01)
[ 7.361400] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 7.361404] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 8.307104] kjournald starting. Commit interval 5 seconds
[ 8.307456] EXT3 FS on sda3, internal journal
[ 8.307462] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.663347] tg3 0000:08:00.0: PME# disabled
[ 9.663517] alloc irq_desc for 31 on cpu 0 node 0
[ 9.663521] alloc kstat_irqs on cpu 0 node 0
[ 9.663547] tg3 0000:08:00.0: irq 31 for MSI/MSI-X
[ 9.716188] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.561091] tg3: eth0: Link is down.
[ 11.561006] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 11.561010] tg3: eth0: Flow control is on for TX and on for RX.
[ 11.561475] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.831691] mtrr: no more MTRRs available
[ 11.831716] mtrr: no more MTRRs available
[ 11.831735] mtrr: no more MTRRs available
[ 11.831754] mtrr: no more MTRRs available
[ 11.831773] mtrr: no more MTRRs available
[ 11.831792] mtrr: no more MTRRs available
[ 11.831810] mtrr: no more MTRRs available
[ 22.180018] eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
tg3 100132 0
broadcom 5360 0
libphy 23616 2 tg3,broadcom
loop 15980 0
joydev 11072 0
snd_hda_codec_intelhdmi 13232 1
b43 122296 0
rfkill 12116 1 b43
rng_core 4872 1 b43
i2c_i801 10464 0
snd_hda_intel 26680 1
snd_hda_codec 75248 2 snd_hda_codec_intelhdmi,snd_hda_intel
mac80211 161424 1 b43
cfg80211 65464 2 b43,mac80211
snd_hwdep 8152 1 snd_hda_codec
snd_pcm 78472 2 snd_hda_intel,snd_hda_codec
led_class 5048 1 b43
snd_timer 21824 1 snd_pcm
snd 63912 8
snd_hda_codec_intelhdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
uvcvideo 56700 0
videodev 36768 1 uvcvideo
v4l1_compat 12932 2 uvcvideo,videodev
soundcore 7984 1 snd
v4l2_compat_ioctl32 9312 1 videodev
snd_page_alloc 9984 2 snd_hda_intel,snd_pcm
i2c_core 25456 1 i2c_i801
serio_raw 5844 0
pcspkr 2800 0
input_polldev 4544 1 b43
psmouse 42172 0
evdev 10448 5
battery 7840 0
ac 3872 0
processor 40208 1
button 6512 0
wmi 7488 0
ext3 122848 2
jbd 48152 1 ext3
mbcache 8804 1 ext3
sd_mod 33736 4
crc_t10dif 2096 1 sd_mod
ahci 36480 3
libata 175660 1 ahci
ssb 43808 1 b43
pcmcia 27640 2 b43,ssb
uhci_hcd 22208 0
pcmcia_core 37108 3 b43,ssb,pcmcia
scsi_mod 158768 2 sd_mod,libata
ehci_hcd 33996 0
intel_agp 28976 1
video 21884 0
output 3472 1 video
thermal 15936 0
fan 5240 0
thermal_sys 16448 4 processor,video,thermal,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory
Controller Hub [8086:2a40] (rev 07)
Subsystem: Lenovo Device [17aa:3a00]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series
Chipset Integrated Graphics Controller [8086:2a42] (rev 07) (prog-if 00 [VGA
controller])
Subsystem: Lenovo Device [17aa:3a02]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset
Integrated Graphics Controller [8086:2a43] (rev 07)
Subsystem: Lenovo Device [17aa:3a02]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f4400000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 [8086:2937] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device [17aa:3a09]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1820 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 [8086:2938] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device [17aa:3a0a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1840 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 [8086:2939] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device [17aa:3a0b]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 1860 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 [8086:293c] (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device [17aa:3a0c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at f4804800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio
Controller [8086:293e] (rev 03)
Subsystem: Lenovo Device [17aa:3a0d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f4600000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 1 [8086:2940] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 2 [8086:2942] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f2000000-f3ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 3 [8086:2944] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 4 [8086:2946] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 5 [8086:2948] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 6 [8086:294a] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Memory behind bridge: f4500000-f45fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 [8086:2934] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device [17aa:3a14]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 [8086:2935] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device [17aa:3a15]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 [8086:2936] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device [17aa:3a16]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 18c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 [8086:293a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device [17aa:3a17]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f4804c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M-E LPC Interface Controller
[8086:2917] (rev 03)
Subsystem: Lenovo Device [17aa:3a19]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI
Controller [8086:2929] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device [17aa:3a1a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 30
Region 0: I/O ports at 1818 [size=8]
Region 1: I/O ports at 180c [size=4]
Region 2: I/O ports at 1810 [size=8]
Region 3: I/O ports at 1808 [size=4]
Region 4: I/O ports at 18e0 [size=32]
Region 5: Memory at f4804000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller
[8086:2930] (rev 03)
Subsystem: Lenovo Device [17aa:3a1d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at 88000000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c00 [size=32]
Kernel driver in use: i801_smbus
03:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g
[14e4:4315] (rev 01)
Subsystem: Broadcom Corporation Device [14e4:04ad]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f2000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
08:00.0 Ethernet controller [0200]: Broadcom Corporation Device [14e4:1692]
(rev 01)
Subsystem: Lenovo Device [17aa:38a2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 31
Region 0: Memory at f4500000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
-- System Information:
Debian Release: squeeze/sid
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.30-2-amd64 (SMP w/1 CPU core)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.30-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.27 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.10-3 tools for managing Linux kernel mo
linux-image-2.6.30-2-amd64 recommends no packages.
Versions of packages linux-image-2.6.30-2-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.30 <none> (no description available)
-- debconf information:
linux-image-2.6.30-2-amd64/preinst/bootloader-initrd-2.6.30-2-amd64: true
linux-image-2.6.30-2-amd64/postinst/bootloader-error-2.6.30-2-amd64:
* linux-image-2.6.30-2-amd64/prerm/removing-running-kernel-2.6.30-2-amd64: true
linux-image-2.6.30-2-amd64/postinst/depmod-error-2.6.30-2-amd64: false
linux-image-2.6.30-2-amd64/postinst/depmod-error-initrd-2.6.30-2-amd64: false
linux-image-2.6.30-2-amd64/preinst/overwriting-modules-2.6.30-2-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.30-2-amd64/preinst/initrd-2.6.30-2-amd64:
linux-image-2.6.30-2-amd64/preinst/failed-to-move-modules-2.6.30-2-amd64:
linux-image-2.6.30-2-amd64/preinst/lilo-initrd-2.6.30-2-amd64: true
linux-image-2.6.30-2-amd64/postinst/old-dir-initrd-link-2.6.30-2-amd64: true
linux-image-2.6.30-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.30-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.30-2-amd64/preinst/abort-overwrite-2.6.30-2-amd64:
linux-image-2.6.30-2-amd64/prerm/would-invalidate-boot-loader-2.6.30-2-amd64:
true
linux-image-2.6.30-2-amd64/postinst/create-kimage-link-2.6.30-2-amd64: true
linux-image-2.6.30-2-amd64/postinst/bootloader-test-error-2.6.30-2-amd64:
linux-image-2.6.30-2-amd64/postinst/old-system-map-link-2.6.30-2-amd64: true
linux-image-2.6.30-2-amd64/postinst/old-initrd-link-2.6.30-2-amd64: true
linux-image-2.6.30-2-amd64/preinst/abort-install-2.6.30-2-amd64:
linux-image-2.6.30-2-amd64/preinst/elilo-initrd-2.6.30-2-amd64: true
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email
______________________________________________________________________
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
