Package: linux-image-2.6.26-2-686
Version: 2.6.26-19lenny1
Severity: important
File: forcedeth
Debian 5.0 netinstall problem with network cards build-in on motherboard
P5N32-E SLI. forcedeth module loaded, however both network interfaces fail
to connect to LAN. Pinging loopback interface works. Anything outside the
network card is unreachable. Quick solution to this problem is to use
modprobe during the installation process ( ALT+F2 ) to remove forcedeth
module and load it back with forcedeth msi=0 msix=0.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-19lenny1) (da...@debian.org)
(gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sat Oct
17 17:59:23 UTC 2009
** Command line:
root=/dev/hdb1 ro quiet
** Not tainted
** Kernel log:
[ 11.776226] PCI: Setting latency timer of device 0000:00:12.0 to 64
[ 12.297261] forcedeth 0000:00:12.0: ifname eth1, PHY OUI 0x5043 @ 1,
addr 00:1a:92:61:b0:eb
[ 12.297264] forcedeth 0000:00:12.0: highdma csum vlan pwrctl mgmt
timirq gbit lnktim msi desc-v3
[ 13.205721] Uniform Multi-Platform E-IDE driver
[ 13.205721] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 13.217721] NFORCE-MCP55: 0000:00:0d.0 (rev a1) UDMA133 controller
[ 13.217721] NFORCE-MCP55: IDE controller (0x10de:0x036e rev 0xa1) at
PCI slot 0000:00:0d.0
[ 13.217721] NFORCE-MCP55: not 100% native mode: will probe irqs later
[ 13.217721] NFORCE-MCP55: BIOS didn't set cable bits correctly.
Enabling workaround.
[ 13.217721] NFORCE-MCP55: IDE port disabled
[ 13.217721] ide0: BM-DMA at 0xfc00-0xfc07
[ 13.217721] Probing IDE interface ide0...
[ 13.230914] usbcore: registered new interface driver hiddev
[ 13.238130] input: Microsoft Microsoft Optical Mouse with Tilt Wheel as
/class/input/input1
[ 13.238637] Driver 'sd' needs updating - please use bus_type methods
[ 13.238637] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors
(74356 MB)
[ 13.238637] sd 0:0:0:0: [sda] Write Protect is off
[ 13.238637] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.238637] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 13.238637] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors
(74356 MB)
[ 13.238637] sd 0:0:0:0: [sda] Write Protect is off
[ 13.238637] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.238637] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 13.238637] sda:<4>Driver 'sr' needs updating - please use bus_type
methods
[ 13.244814] input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft
Optical Mouse with Tilt Wheel] on usb-0000:00:0b.0-1
[ 13.244828] usbcore: registered new interface driver usbhid
[ 13.244830] usbhid: v2.6:USB HID core driver
[ 13.251282] sda1 sda2 sda3
[ 13.263281] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.270855] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2
cdda tray
[ 13.270858] Uniform CD-ROM driver Revision: 3.20
[ 13.270911] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 13.278352] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 13.278352] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 13.543826] hda: ST380023A, ATA DISK drive
[ 13.804734] hdb: ST310211A, ATA DISK drive
[ 13.878261] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 13.878733] hda: UDMA/100 mode selected
[ 13.878981] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 13.879128] hdb: UDMA/100 mode selected
[ 13.879249] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 13.970209] hda: max request size: 128KiB
[ 13.970210] hda: 156301488 sectors (80026 MB) w/2048KiB Cache,
CHS=65535/16/63
[ 13.970210] hda: cache flushes supported
[ 13.970210] hda: hda1
[ 13.988814] hdb: max request size: 128KiB
[ 13.988814] hdb: 19541088 sectors (10005 MB) w/512KiB Cache,
CHS=19386/16/63
[ 13.988814] hdb: cache flushes not supported
[ 13.988814] hdb: hdb1 hdb2 < hdb5 >
[ 15.059283] PM: Starting manual resume from disk
[ 15.137701] kjournald starting. Commit interval 5 seconds
[ 15.137701] EXT3-fs: mounted filesystem with ordered data mode.
[ 17.964749] udevd version 125 started
[ 18.786534] input: PC Speaker as /class/input/input2
[ 18.841281] input: Power Button (FF) as /class/input/input3
[ 18.855222] ACPI: Power Button (FF) [PWRF]
[ 18.855264] input: Power Button (CM) as /class/input/input4
[ 18.863207] ACPI: Power Button (CM) [PWRB]
[ 19.040039] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[ 19.040039] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c80
[ 19.685092] Linux video capture interface: v2.00
[ 19.897613] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0990)
[ 19.920473] input: UVC Camera (046d:0990) as /class/input/input5
[ 19.924656] usbcore: registered new interface driver uvcvideo
[ 19.924656] USB Video Class driver (v0.1.0)
[ 19.986048] usbcore: registered new interface driver snd-usb-audio
[ 20.064596] Error: Driver 'pcspkr' is already registered, aborting...
[ 20.096565] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
[ 20.096565] ACPI: PCI Interrupt 0000:00:0f.1[B] -> Link [AAZA] -> GSI
20 (level, low) -> IRQ 20
[ 20.096565] PCI: Setting latency timer of device 0000:00:0f.1 to 64
[ 20.137122] hda_codec: Unknown model for AD1988, trying auto-probe from
BIOS...
[ 21.474980] Adding 465844k swap on /dev/hdb5. Priority:-1 extents:1
across:465844k
[ 21.813541] EXT3 FS on hdb1, internal journal
[ 22.849894] loop: module loaded
[ 26.436756] NET: Registered protocol family 10
[ 26.436756] lo: Disabled Privacy Extensions
[ 40.875582] eth0: no IPv6 routers present
[ 246.900828] ACPI: PCI interrupt for device 0000:00:12.0 disabled
[ 246.944666] ACPI: PCI interrupt for device 0000:00:11.0 disabled
[ 276.516563] forcedeth: Reverse Engineered nForce ethernet driver.
Version 0.61.
[ 276.516563] ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [APCH] -> GSI
22 (level, low) -> IRQ 22
[ 276.516563] PCI: Setting latency timer of device 0000:00:11.0 to 64
[ 277.125401] forcedeth 0000:00:11.0: ifname eth0, PHY OUI 0x5043 @ 1,
addr 00:1a:92:61:a4:53
[ 277.125401] forcedeth 0000:00:11.0: highdma csum vlan pwrctl mgmt
timirq gbit lnktim desc-v3
[ 277.125401] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [AMC1] -> GSI
21 (level, low) -> IRQ 21
[ 277.125401] PCI: Setting latency timer of device 0000:00:12.0 to 64
[ 277.301197] eth0: no link during initialization.
[ 277.303362] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 277.800041] forcedeth 0000:00:12.0: ifname eth1, PHY OUI 0x5043 @ 1,
addr 00:1a:92:61:b0:eb
[ 277.800046] forcedeth 0000:00:12.0: highdma csum vlan pwrctl mgmt
timirq gbit lnktim desc-v3
[ 279.070566] eth0: link up.
[ 279.070566] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 293.673845] eth0: no IPv6 routers present
[ 764.772570] uvcvideo: Failed to query (1) UVC control 1 (unit 0) : -110
(exp. 26).
[ 783.035638] 3:3:1: cannot set freq 16000 to ep 0x86
[ 885.985548] usb 2-6: new full speed USB device using ohci_hcd and
address 3
[ 887.043252] usb 2-6: configuration #1 chosen from 1 choice
[ 887.047447] usb 2-6: New USB device found, idVendor=041e, idProduct=401a
[ 887.047450] usb 2-6: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 945.901441] usb 2-6: USB disconnect, address 3
** Loaded modules:
Module Size Used by
forcedeth 45072 0
ipv6 235396 20
loop 12748 0
snd_hda_intel 325720 0
snd_pcm_oss 32800 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_usb_audio 70272 0
snd_usb_lib 13440 1 snd_usb_audio
uvcvideo 45800 0
snd_rawmidi 18496 1 snd_usb_lib
snd_seq_device 6380 1 snd_rawmidi
snd_pcm 62660 3 snd_hda_intel,snd_pcm_oss,snd_usb_audio
compat_ioctl32 1312 1 uvcvideo
snd_hwdep 6212 1 snd_usb_audio
videodev 27520 1 uvcvideo
snd_timer 17800 1 snd_pcm
snd 45636 9
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_usb_audio,snd_rawmidi,snd_seq_device,snd_pcm,snd_hwdep,snd_timer
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
v4l1_compat 12260 2 uvcvideo,videodev
i2c_nforce2 5536 0
i2c_core 19828 1 i2c_nforce2
button 6096 0
pcspkr 2432 0
soundcore 6368 1 snd
evdev 8000 4
ext3 105576 1
jbd 39476 1 ext3
mbcache 7108 1 ext3
ide_disk 10496 3
sg 26964 0
sr_mod 13316 0
sd_mod 22200 0
cdrom 30176 1 sr_mod
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
amd74xx 7752 0 [permanent]
ide_pci_generic 3908 0 [permanent]
ide_core 96168 3 ide_disk,amd74xx,ide_pci_generic
ata_generic 4676 0
sata_nv 19848 0
ohci_hcd 18532 0
libata 140448 2 ata_generic,sata_nv
ehci_hcd 28428 0
usbcore 118192 7
snd_usb_audio,snd_usb_lib,uvcvideo,usbhid,ohci_hcd,ehci_hcd
scsi_mod 129548 4 sg,sr_mod,sd_mod,libata
dock 8304 1 libata
thermal 15228 0
processor 32576 1 thermal
fan 4196 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: nVidia Corporation C55 Host Bridge [10de:03a1]
(rev a2)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:00.1 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03ac] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.2 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03aa] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03a9] (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.4 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03ab] (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.5 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03a8] (rev a2)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.6 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03b5] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.7 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03b4] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.0 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03ad] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.1 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03ae] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.2 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03af] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.3 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03b0] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.4 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03b1] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.5 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03b2] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.6 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03b3] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:02.0 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03b6] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:02.1 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03bc] (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.2 RAM memory [0500]: nVidia Corporation C55 Memory Controller
[10de:03ba] (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:03.0 PCI bridge [0604]: nVidia Corporation C55 PCI Express bridge
[10de:03b7] (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ea000000-edffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:06.0 PCI bridge [0604]: nVidia Corporation C55 PCI Express bridge
[10de:03b9] (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: efc00000-efcfffff
Prefetchable memory behind bridge: 00000000ef900000-00000000ef9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:07.0 PCI bridge [0604]: nVidia Corporation C55 PCI Express bridge
[10de:03bb] (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: efe00000-efefffff
Prefetchable memory behind bridge: 00000000efd00000-00000000efdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:09.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller
[10de:0369] (rev a1)
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge [10de:0360]
(rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:0a.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at ff00 [size=64]
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 1c80 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:0a.2 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller
[10de:036a] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:0b.0 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036c] (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at effff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0b.1 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036d] (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at efffe000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:0d.0 IDE interface [0101]: nVidia Corporation MCP55 IDE [10de:036e]
(rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
Kernel modules: amd74xx
00:0e.0 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at f700 [size=16]
Region 5: Memory at efffd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:0e.1 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at f200 [size=16]
Region 5: Memory at efffc000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:0e.2 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 23
Region 0: I/O ports at f100 [size=8]
Region 1: I/O ports at f000 [size=4]
Region 2: I/O ports at ef00 [size=8]
Region 3: I/O ports at ee00 [size=4]
Region 4: I/O ports at ed00 [size=16]
Region 5: Memory at efffb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:0f.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge [10de:0370]
(rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: efb00000-efbfffff
Prefetchable memory behind bridge: efa00000-efafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn+
Capabilities: <access denied>
00:0f.1 Audio device [0403]: nVidia Corporation MCP55 High Definition
Audio [10de:0371] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81f2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at efff0000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:11.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at efffa000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at efff9000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at efff8000 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:12.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at efff7000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at eb00 [size=8]
Region 2: Memory at efff6000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at efff5000 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:13.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0376] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: ef800000-ef8fffff
Prefetchable memory behind bridge: 00000000ef700000-00000000ef7fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:14.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0374] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: ef600000-ef6fffff
Prefetchable memory behind bridge: 00000000ef500000-00000000ef5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:15.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0374] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: ef400000-ef4fffff
Prefetchable memory behind bridge: 00000000ef300000-00000000ef3fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:16.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0378] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: ef200000-ef2fffff
Prefetchable memory behind bridge: 00000000ef100000-00000000ef1fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:17.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0375] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: ef000000-ef0fffff
Prefetchable memory behind bridge: 00000000eef00000-00000000eeffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:18.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0377] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: eee00000-eeefffff
Prefetchable memory behind bridge: 00000000eed00000-00000000eedfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
01:00.0 VGA compatible controller [0300]: nVidia Corporation GeForce 8800
Ultra [10de:0194] (rev a2) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Device [1462:8010]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 7
Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at ea000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at df00 [size=128]
Expansion ROM at edfe0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: nvidiafb
-- System Information:
Debian Release: 5.0.3
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/4 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration
management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an
initramfs
ii module-init-tools 3.4-1 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared
libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader
(Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686:
true
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
