Package: linux-image-2.6.26-1-486 Version: 2.6.26-13 Severity: normal
dd if=/dev/zero of=/dev/hda causes disk reads. Using dd if=/dev/zero of=/dev/hda bs=Nk causes no disk reads for sufficiently large N which varies per drive model. I see this as a failure of the block subsystem. Writing should not require re-reading even if I was writing per character. -- Package-specific info: ** Version: Linux version 2.6.26-1-486 (Debian 2.6.26-13) (michal.sucha...@ruk.cuni.cz) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Thu Feb 12 00:35:28 CET 2009 ** Command line: initrd=initrd1.img boot=live xdebconf g username=ghost hostname=debian-ghost union=aufs quickreboot httpfs=http://195.113.15.10/filesystem.squashfs vga=792 splash quiet BOOT_IMAGE=vmlinuz1 ** Not tainted ** Kernel log: [ 5.340335] usb usb4: configuration #1 chosen from 1 choice [ 5.340363] hub 4-0:1.0: USB hub found [ 5.340372] hub 4-0:1.0: 2 ports detected [ 5.444118] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 5.444122] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.444126] usb usb4: Product: UHCI Host Controller [ 5.444128] usb usb4: Manufacturer: Linux 2.6.26-1-486 uhci_hcd [ 5.444131] usb usb4: SerialNumber: 0000:00:10.3 [ 5.444183] ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21 [ 5.444199] ehci_hcd 0000:00:10.4: EHCI Host Controller [ 5.444226] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 [ 5.444269] ehci_hcd 0000:00:10.4: irq 21, io mem 0xe6000000 [ 5.456010] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 5.456095] usb usb5: configuration #1 chosen from 1 choice [ 5.456125] hub 5-0:1.0: USB hub found [ 5.456134] hub 5-0:1.0: 8 ports detected [ 5.560091] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.560095] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.560098] usb usb5: Product: EHCI Host Controller [ 5.560100] usb usb5: Manufacturer: Linux 2.6.26-1-486 ehci_hcd [ 5.560103] usb usb5: SerialNumber: 0000:00:10.4 [ 5.560429] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23 [ 5.560436] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 23 [ 5.560761] eth0: VIA Rhine II at 0x1ec00, 00:13:d3:a5:a3:77, IRQ 23. [ 5.561473] eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link c5e1. [ 5.565747] sata_via 0000:00:0f.0: version 2.3 [ 5.565777] ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20 [ 5.565831] sata_via 0000:00:0f.0: routed to hard irq line 11 [ 5.565904] scsi0 : sata_via [ 5.565984] scsi1 : sata_via [ 5.566019] ata1: SATA max UDMA/133 cmd 0xe000 ctl 0xe100 bmdma 0xe400 irq 20 [ 5.566022] ata2: SATA max UDMA/133 cmd 0xe200 ctl 0xe300 bmdma 0xe408 irq 20 [ 5.603086] hda: max request size: 128KiB [ 5.603092] hda: 12500460 sectors (6400 MB) w/256KiB Cache, CHS=13228/15/63 [ 5.603098] hda: cache flushes not supported [ 5.603134] hda: hda1 [ 5.607511] hdb: max request size: 128KiB [ 5.607515] hdb: 12500460 sectors (6400 MB) w/256KiB Cache, CHS=13228/15/63 [ 5.607520] hdb: cache flushes not supported [ 5.607543] hdb: hdb1 hdb2 hdb3 [ 5.612199] hdc: max request size: 128KiB [ 5.612203] hdc: 40079088 sectors (20520 MB) w/512KiB Cache, CHS=39761/16/63 [ 5.612208] hdc: cache flushes not supported [ 5.612235] hdc: hdc1 [ 5.768104] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300) [ 5.972010] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300) [ 6.584803] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports [ 6.584813] ide_generic: I/O resource 0x1F0-0x1F7 not free. [ 6.586350] ide_generic: I/O resource 0x170-0x177 not free. [ 6.764035] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 6.940984] usb 3-1: configuration #1 chosen from 1 choice [ 6.954034] usb 3-1: New USB device found, idVendor=04a5, idProduct=7003 [ 6.954039] usb 3-1: New USB device strings: Mfr=4, Product=20, SerialNumber=0 [ 6.954043] usb 3-1: Product: Generic USB Keyboard [ 6.954045] usb 3-1: Manufacturer: NOVATEK [ 7.192031] usb 4-1: new low speed USB device using uhci_hcd and address 2 [ 7.367935] usb 4-1: configuration #1 chosen from 1 choice [ 7.370950] usb 4-1: New USB device found, idVendor=046d, idProduct=c063 [ 7.370954] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 7.370957] usb 4-1: Product: DELL USB Laser Mouse [ 7.370959] usb 4-1: Manufacturer: DELL [ 7.629595] usbcore: registered new interface driver hiddev [ 7.652193] input: NOVATEK Generic USB Keyboard as /class/input/input0 [ 7.652442] input,hidraw0: USB HID v1.10 Keyboard [NOVATEK Generic USB Keyboard] on usb-0000:00:10.2-1 [ 7.664005] input: DELL DELL USB Laser Mouse as /class/input/input1 [ 7.664005] input,hidraw1: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:10.3-1 [ 7.664005] usbcore: registered new interface driver usbhid [ 7.664005] usbhid: v2.6:USB HID core driver [ 7.740272] eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1 [ 8.766739] fuse init (API version 7.9) [ 8.790138] aufs 20080714 [ 8.813049] loop: module loaded [ 8.885682] squashfs: version 3.3-CVS (2008/04/04) Phillip Lougher [ 24.787989] udevd version 125 started [ 26.676677] Linux agpgart interface v0.103 [ 26.678266] agpgart: Detected AGP bridge 0 [ 26.695449] agpgart: AGP aperture is 512M @ 0xc0000000 [ 26.943916] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 26.945618] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 27.224351] input: Power Button (FF) as /class/input/input2 [ 27.252122] ACPI: Power Button (FF) [PWRF] [ 27.252201] input: Power Button (CM) as /class/input/input3 [ 27.276045] ACPI: Power Button (CM) [PWRB] [ 28.821973] input: PC Speaker as /class/input/input4 [ 29.282180] parport_pc 00:0b: reported by Plug and Play ACPI [ 29.282235] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] [ 29.531731] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22 [ 29.531740] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22 [ 29.531884] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 32.213397] device-mapper: uevent: version 1.0.3 [ 32.214378] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-de...@redhat.com [ 36.799810] NET: Registered protocol family 10 [ 36.800367] lo: Disabled Privacy Extensions [ 44.627491] [drm] Initialized drm 1.1.0 20060810 [ 44.645222] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 44.645353] [drm] Initialized via 2.11.1 20070202 on minor 0 [ 44.653988] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. [ 44.654014] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode [ 44.654077] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode [ 46.932008] eth0: no IPv6 routers present ** Loaded modules: Module Size Used by via 34304 1 drm 64672 2 via ipv6 225172 8 dm_crypt 11012 0 crypto_blkcipher 14724 1 dm_crypt dm_mod 45384 1 dm_crypt md_mod 65940 0 snd_via82xx 20248 0 gameport 10504 1 snd_via82xx snd_ac97_codec 88228 1 snd_via82xx ac97_bus 1664 1 snd_ac97_codec snd_pcm_oss 32544 0 snd_mixer_oss 12288 1 snd_pcm_oss snd_pcm 60680 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss snd_page_alloc 7816 2 snd_via82xx,snd_pcm snd_mpu401_uart 6400 1 snd_via82xx parport_pc 22436 0 parport 30408 1 parport_pc snd_seq_dummy 2692 0 snd_seq_oss 24832 0 snd_seq_midi 5664 0 snd_rawmidi 18592 2 snd_mpu401_uart,snd_seq_midi pcspkr 2304 0 snd_seq_midi_event 6528 2 snd_seq_oss,snd_seq_midi k8temp 4096 0 snd_seq 40784 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event snd_timer 17668 2 snd_pcm,snd_seq snd_seq_device 6412 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq snd 44964 11 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device i2c_viapro 6804 0 i2c_core 19728 1 i2c_viapro soundcore 6112 1 snd button 6032 0 shpchp 25496 0 pci_hotplug 23204 1 shpchp amd64_agp 8836 1 agpgart 28336 2 drm,amd64_agp evdev 7808 3 battery 10116 0 squashfs 35976 1 zlib_inflate 14080 1 squashfs loop 12428 2 aufs 108304 1 exportfs 3712 1 aufs fuse 41116 3 usbhid 35712 0 hid 32128 1 usbhid ff_memless 4232 1 usbhid ide_generic 2432 0 [permanent] ide_disk 10496 3 sata_via 6916 0 floppy 47620 0 via_rhine 18184 0 mii 4864 1 via_rhine ehci_hcd 28300 0 uhci_hcd 18448 0 ata_generic 4612 0 usbcore 117616 4 usbhid,ehci_hcd,uhci_hcd libata 141088 2 sata_via,ata_generic via82cxxx 6916 0 [permanent] scsi_mod 129804 1 libata dock 8076 1 libata ide_pci_generic 3844 0 [permanent] ide_core 95144 4 ide_generic,ide_disk,via82cxxx,ide_pci_generic thermal 15132 0 processor 28080 1 thermal fan 4100 0 thermal_sys 10784 3 thermal,processor,fan atl2 22424 0 ** PCI devices: 00:00.0 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:0204] Subsystem: VIA Technologies, Inc. K8M800 Host Bridge [1106:0204] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 8 Region 0: Memory at c0000000 (32-bit, prefetchable) [size=512M] Capabilities: <access denied> Kernel driver in use: agpgart-amd64 Kernel modules: amd64-agp 00:00.1 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:1204] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.2 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:2204] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.3 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:3204] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.4 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:4204] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.7 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:7204] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] [1106:b188] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e4000000-e5ffffff Prefetchable memory behind bridge: e0000000-e3ffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+ BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel modules: shpchp 00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin B routed to IRQ 20 Region 0: I/O ports at e000 [size=8] Region 1: I/O ports at e100 [size=4] Region 2: I/O ports at e200 [size=8] Region 3: I/O ports at e300 [size=4] Region 4: I/O ports at e400 [size=16] Region 5: I/O ports at e500 [size=256] Capabilities: <access denied> Kernel driver in use: sata_via Kernel modules: sata_via 00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 20 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at e600 [size=16] Capabilities: <access denied> Kernel driver in use: VIA_IDE Kernel modules: via82cxxx 00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at e700 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at e800 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at e900 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at ea00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI]) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 21 Region 0: Memory at e6000000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] [1106:3227] Subsystem: VIA Technologies, Inc. DFI KT600-AL / Soltek SL-B9D-FGR Motherboard [1106:3227] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: i2c-viapro 00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 60) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 22 Region 0: I/O ports at eb00 [size=256] Capabilities: <access denied> Kernel driver in use: VIA 82xx Audio Kernel modules: snd-via82xx 00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 78) Subsystem: Micro-Star International Co., Ltd. K8MM3-V mainboard [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at ec00 [size=256] Region 1: Memory at e6001000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine Kernel modules: via-rhine 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel driver in use: k8temp Kernel modules: k8temp 01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. K8M800/K8N800/K8N800A [S3 UniChrome Pro] [1106:3108] (rev 01) (prog-if 00 [VGA controller]) Subsystem: Micro-Star International Co., Ltd. Device [1462:7181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min) Interrupt: pin A routed to IRQ 16 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at e4000000 (32-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at e5000000 [disabled] [size=64K] Capabilities: <access denied> -- System Information: Debian Release: 5.0 APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 2.6.26-1-486 Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages linux-image-2.6.26-1-486 depends on: ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs ii module-init-tools 3.4-1 tools for managing Linux kernel mo linux-image-2.6.26-1-486 recommends no packages. Versions of packages linux-image-2.6.26-1-486 suggests: ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v ii lilo 1:22.8-7 LInux LOader - The Classic OS load pn linux-doc-2.6.26 <none> (no description available) -- debconf information excluded -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
