Package: linux-image-2.6.29-2-amd64
Version: 2.6.29-5
Severity: important
*** Please type your report below this line ***
I am having some troubles with PXE booting our servers that are running
fully up to date Debian Squeeze/Sid. The servers have AMD Opteron 1218
on a supermicro H8SMU motherboard using the nVidia MCP55 Pro chipset.
The problem I am running into is that after Squeeze/Sid has been
installed, on reboots of the machine, the nVidia PXE bootloader fails to
start, giving the error message: "PXE-E61: Media test failure check cable".
Going into the BIOS screen on boot and clearing the NVRAM or changing a
setting and saving will correct the problem for the next boot. However,
on a subsequent reboot the same error occurs. Also, rebooting after the
PXE failure at the GRUB screen will also cause PXE booting to happen
normally until Debian Squeeze/Sid fully boots up.
The netbooting error does not occur with Debian 4.0, Debian 5.0, nor
many other linux distributions.
-- Package-specific info:
** Version:
Linux version 2.6.29-2-amd64 (Debian 2.6.29-5) (wa...@debian.org) (gcc
version 4.3.3 (Debian 4.3.3-10) ) #1 SMP Sun May 17 17:15:47 UTC 2009
** Command line:
ro root=/dev/sda1 root=/dev/sda1 ro quiet
** Not tainted
** Kernel log:
[ 0.884806] sata_nv 0000:00:05.0: PCI INT A -> Link[LSA0] -> GSI 20
(level, low) -> IRQ 20
[ 0.884808] sata_nv 0000:00:05.0: Using SWNCQ mode
[ 0.884867] sata_nv 0000:00:05.0: setting latency timer to 64
[ 0.885006] scsi0 : sata_nv
[ 0.896293] Uniform Multi-Platform E-IDE driver
[ 0.896423] scsi1 : sata_nv
[ 0.896587] ata1: SATA max UDMA/133 cmd 0xd480 ctl 0xd400 bmdma
0xcc00 irq 20
[ 0.896589] ata2: SATA max UDMA/133 cmd 0xd080 ctl 0xd000 bmdma
0xcc08 irq 20
[ 0.908853] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.776032] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.811487] ata1.00: ATA-8: ST3320613AS, CC2F, max UDMA/133
[ 1.811490] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth
31/32)
[ 1.867488] ata1.00: configured for UDMA/133
[ 1.867530] isa bounce pool size: 16 pages
[ 1.867599] scsi 0:0:0:0: Direct-Access ATA ST3320613AS
CC2F PQ: 0 ANSI: 5
[ 2.598197] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.598226] amd74xx 0000:00:04.0: UDMA133 controller
[ 2.598229] amd74xx 0000:00:04.0: IDE controller (0x10de:0x036e rev
0xa1)
[ 2.598244] amd74xx 0000:00:04.0: IDE port disabled
[ 2.598255] amd74xx 0000:00:04.0: not 100% native mode: will probe
irqs later
[ 2.598259] ide0: BM-DMA at 0xffa0-0xffa7
[ 2.598264] Probing IDE interface ide0...
[ 3.612084] hdb: MATSHITADVD-ROM SR-8178, ATAPI CD/DVD-ROM drive
[ 3.668034] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 3.668288] hdb: host side 80-wire cable detection failed, limiting
max speed to UDMA33
[ 3.668290] hdb: UDMA/33 mode selected
[ 3.668565] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 3.671511] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[ 3.671515] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 23
(level, low) -> IRQ 23
[ 3.671544] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 3.671547] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 3.671621] ohci_hcd 0000:00:02.0: new USB bus registered, assigned
bus number 2
[ 3.671634] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfeafb000
[ 3.726014] usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
[ 3.726016] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.726018] usb usb2: Product: OHCI Host Controller
[ 3.726020] usb usb2: Manufacturer: Linux 2.6.29-2-amd64 ohci_hcd
[ 3.726021] usb usb2: SerialNumber: 0000:00:02.0
[ 3.726065] usb usb2: configuration #1 chosen from 1 choice
[ 3.726090] hub 2-0:1.0: USB hub found
[ 3.726097] hub 2-0:1.0: 10 ports detected
[ 3.726471] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 22
[ 3.726473] sata_nv 0000:00:05.1: PCI INT B -> Link[LSA1] -> GSI 22
(level, low) -> IRQ 22
[ 3.726475] sata_nv 0000:00:05.1: Using SWNCQ mode
[ 3.726525] sata_nv 0000:00:05.1: setting latency timer to 64
[ 3.726644] scsi2 : sata_nv
[ 3.726702] scsi3 : sata_nv
[ 3.726824] ata3: SATA max UDMA/133 cmd 0xc880 ctl 0xc800 bmdma
0xc080 irq 22
[ 3.726827] ata4: SATA max UDMA/133 cmd 0xc480 ctl 0xc400 bmdma
0xc088 irq 22
[ 4.100014] usb 2-2: new low speed USB device using ohci_hcd and
address 2
[ 4.316026] usb 2-2: New USB device found, idVendor=045e, idProduct=00cb
[ 4.316029] usb 2-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.316032] usb 2-2: Product: Microsoft Basic Optical Mouse v2.0
[ 4.316033] usb 2-2: Manufacturer: Microsoft
[ 4.316096] usb 2-2: configuration #1 chosen from 1 choice
[ 4.326254] usbcore: registered new interface driver hiddev
[ 4.332253] input: Microsoft Microsoft Basic Optical Mouse v2.0 as
/devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.0/input/input2
[ 4.341056] generic-usb 0003:045E:00CB.0001: input,hidraw0: USB HID
v1.11 Mouse [Microsoft Microsoft Basic Optical Mouse v2.0 ] on
usb-0000:00:02.0-2/input0
[ 4.341076] usbcore: registered new interface driver usbhid
[ 4.341079] usbhid: v2.6:USB HID core driver
[ 4.458200] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.190194] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.196970] ide-cd driver 5.00
[ 5.197549] ide-cd: hdb: ATAPI 24X DVD-ROM drive, 256kB Cache
[ 5.197553] Uniform CD-ROM driver Revision: 3.20
[ 5.296185] Driver 'sd' needs updating - please use bus_type methods
[ 5.296288] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors:
(320 GB/298 GiB)
[ 5.296302] sd 0:0:0:0: [sda] Write Protect is off
[ 5.296304] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.296323] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.296376] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors:
(320 GB/298 GiB)
[ 5.296386] sd 0:0:0:0: [sda] Write Protect is off
[ 5.296388] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.296405] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.296409] sda: sda1 sda2 < sda5 >
[ 5.338866] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.397564] PM: Starting manual resume from disk
[ 5.463119] kjournald starting. Commit interval 5 seconds
[ 5.463128] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.156687] udev: starting version 141
[ 28.433840] input: Power Button (FF) as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 28.441134] ACPI: Power Button (FF) [PWRF]
[ 28.441243] input: Power Button (CM) as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 28.449123] ACPI: Power Button (CM) [PWRB]
[ 28.766572] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2d00
[ 28.766589] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2e00
[ 28.944498] k8temp 0000:00:18.3: Temperature readouts might be wrong
- check erratum #141
[ 29.274190] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 29.330627] Error: Driver 'pcspkr' is already registered, aborting...
[ 30.424987] Adding 20244412k swap on /dev/sda5. Priority:-1
extents:1 across:20244412k
[ 30.561471] EXT3 FS on sda1, internal journal
[ 31.457547] loop: module loaded
[ 32.132177] alloc irq_desc for 30 on cpu 0 node 0
[ 32.132180] alloc kstat_irqs on cpu 0 node 0
[ 32.132189] forcedeth 0000:00:08.0: irq 30 for MSI/MSI-X
[ 35.799212] RPC: Registered udp transport module.
[ 35.799215] RPC: Registered tcp transport module.
[ 37.166622] NET: Registered protocol family 10
[ 37.167196] lo: Disabled Privacy Extensions
[ 47.612011] eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
autofs4 26728 1
ipv6 283776 12
nfs 250560 2
lockd 67924 1 nfs
nfs_acl 3232 1 nfs
auth_rpcgss 40768 1 nfs
sunrpc 194936 13 nfs,lockd,nfs_acl,auth_rpcgss
loop 15292 0
snd_pcsp 10652 0
serio_raw 5780 0
snd_pcm 78776 1 snd_pcsp
snd_timer 22240 1 snd_pcm
snd 63192 3 snd_pcsp,snd_pcm,snd_timer
soundcore 7984 1 snd
snd_page_alloc 9776 1 snd_pcm
k8temp 5008 0
psmouse 41532 0
i2c_nforce2 7400 0
i2c_core 25168 1 i2c_nforce2
evdev 10496 3
button 7280 0
ext3 122528 1
jbd 50232 1 ext3
mbcache 9140 1 ext3
sd_mod 32632 3
crc_t10dif 2064 1 sd_mod
ide_cd_mod 30192 0
cdrom 33592 1 ide_cd_mod
ide_pci_generic 4628 0
usbhid 34176 0
hid 40928 1 usbhid
ata_generic 5876 0
ohci_hcd 23036 0
amd74xx 6840 0
ide_core 108788 3 ide_cd_mod,ide_pci_generic,amd74xx
sata_nv 24840 2
forcedeth 52336 0
libata 172716 2 ata_generic,sata_nv
scsi_mod 158880 2 sd_mod,libata
ehci_hcd 33916 0
thermal 18864 0
processor 45400 1 thermal
fan 5304 0
thermal_sys 13104 3 thermal,processor,fan
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller
[10de:0369] (rev a2)
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge
[10de:0364] (rev a3)
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a3)
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00 [size=64]
Region 4: I/O ports at 2d00 [size=64]
Region 5: I/O ports at 2e00 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
00:02.0 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036c] (rev a1) (prog-if 10 [OHCI])
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at feafb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.1 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036d] (rev a2) (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at feafac00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:04.0 IDE interface [0101]: nVidia Corporation MCP55 IDE [10de:036e]
(rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
00:05.0 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at d480 [size=8]
Region 1: I/O ports at d400 [size=4]
Region 2: I/O ports at d080 [size=8]
Region 3: I/O ports at d000 [size=4]
Region 4: I/O ports at cc00 [size=16]
Region 5: Memory at feaf9000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00:05.1 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at c880 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c480 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c080 [size=16]
Region 5: Memory at feaf8000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00:06.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge
[10de:0370] (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:08.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373]
(rev a3)
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 30
Region 0: Memory at feaf7000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at c000 [size=8]
Region 2: Memory at feafa800 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at feafa400 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:09.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373]
(rev a3)
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at feaf6000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at bc00 [size=8]
Region 2: Memory at feafa000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at feaf5c00 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:0a.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0376] (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0b.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0374] (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0c.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0374] (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0d.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0378] (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0e.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0375] (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0f.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0377] (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
01:06.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000
[1002:515e] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at feb00000 [disabled] [size=128K]
Capabilities: <access denied>
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.29-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.29-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration
management sy
ii initramfs-tools [linux-initra 0.93.2 tools for generating an
initramfs
ii module-init-tools 3.7-pre9-1 tools for managing Linux
kernel mo
linux-image-2.6.29-2-amd64 recommends no packages.
Versions of packages linux-image-2.6.29-2-amd64 suggests:
ii grub 0.97-53 GRand Unified Bootloader
(Legacy v
pn linux-doc-2.6.29 <none> (no description available)
-- debconf information:
linux-image-2.6.29-2-amd64/preinst/abort-install-2.6.29-2-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.29-2-amd64/postinst/old-initrd-link-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/failed-to-move-modules-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/postinst/old-system-map-link-2.6.29-2-amd64:
true
linux-image-2.6.29-2-amd64/preinst/elilo-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/prerm/would-invalidate-boot-loader-2.6.29-2-amd64:
true
linux-image-2.6.29-2-amd64/postinst/create-kimage-link-2.6.29-2-amd64:
true
linux-image-2.6.29-2-amd64/prerm/removing-running-kernel-2.6.29-2-amd64:
true
linux-image-2.6.29-2-amd64/postinst/old-dir-initrd-link-2.6.29-2-amd64:
true
linux-image-2.6.29-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.29-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.29-2-amd64/preinst/initrd-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/postinst/depmod-error-2.6.29-2-amd64: false
linux-image-2.6.29-2-amd64/preinst/abort-overwrite-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/postinst/bootloader-test-error-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/preinst/lilo-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/bootloader-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/overwriting-modules-2.6.29-2-amd64:
true
linux-image-2.6.29-2-amd64/postinst/depmod-error-initrd-2.6.29-2-amd64:
false
linux-image-2.6.29-2-amd64/postinst/bootloader-error-2.6.29-2-amd64:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
