Package: linux-image-2.6.29-2-686-bigmem
Version: 2.6.29-5
Severity: normal
File: linux-image-2.6.29
Hi
After the inclusion of the new firewire stack again, the bug that resulting in
re-detection of the firewire disk as a newly plugged device has not gone away.
To re-hash the situation:
- I suspend my system using suspend to RAM in new KDE4's leave menu.
- System suspends normally.
- Some time passes (as expected)
- I wake my system and system comes back as expected.
- System detects my firewire disk as a new device, gives it a different /dev/
entry, drops the old mountpoint so it appears dead. Making any operations on
old mountpoint generate kernel messages about a dead I/O device.
- To fix the situation, I umount the dead point, remove the disk and re-plug it
and mount everything back (sometimes I need to run an fsck to verify the huge
1TB disk)
This is not convenient, dangerous (I may lose data), most importantly was not
happening before. I'm running an Intel P35 platform and my FireWire controller
is VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller.
I'm running with suspend to disk as a workaround.
Since nobody replied and/or provided additional information I needed to bump
it. I'm a linux system administrator / programmer so I can provide any
additional information you want.
Cheers.
-- Package-specific info:
** Version:
Linux version 2.6.29-2-686-bigmem (Debian 2.6.29-5) (wa...@debian.org) (gcc
version 4.3.3 (Debian 4.3.3-10) ) #1 SMP Sun May 17 19:06:25 UTC 2009
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.29-2-686-bigmem
root=UUID=13da074b-55ea-4214-9ad3-1642e371ab72 ro vga=794
** Tainted: P (1)
** Kernel log:
[130754.965476] ata4: EH complete
[130754.965499] ata5.00: configured for UDMA/133
[130754.965501] ata5: EH complete
[130754.965536] firewire_core: skipped bus generations, destroying all nodes
[130754.965541] saa7134 0000:05:01.0: restoring config space at offset 0x1 (was
0x2900006, writing 0x82900006)
[130754.965552] saa7130[0]: board init: gpio is 39000
[130754.965554] saa7130[0]: there are different flyvideo cards with different
tuners
[130754.965555] saa7130[0]: out there, you might have to use the tuner=<nr>
insmod
[130754.965556] saa7130[0]: option to override the default value.
[130754.965566] sd 4:0:0:0: [sdd] 1953525168 512-byte hardware sectors: (1.00
TB/931 GiB)
[130754.965590] sd 4:0:0:0: [sdd] Write Protect is off
[130754.965592] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[130754.965609] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[130754.965631] sd 3:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00
TB/931 GiB)
[130754.965641] sd 3:0:0:0: [sdc] Write Protect is off
[130754.965643] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[130754.965659] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[130754.965721] ata3.00: configured for UDMA/133
[130754.965723] ata3: EH complete
[130754.965740] sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500
GB/465 GiB)
[130754.965751] sd 2:0:0:0: [sdb] Write Protect is off
[130754.965752] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[130754.965769] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[130754.965788] sd 4:0:0:0: [sdd] 1953525168 512-byte hardware sectors: (1.00
TB/931 GiB)
[130754.965797] sd 4:0:0:0: [sdd] Write Protect is off
[130754.965799] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[130754.965819] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[130754.966092] ata6.00: configured for UDMA/100
[130754.966094] ata6: EH complete
[130755.156037] firewire_core: skipped bus generations, destroying all nodes
[130755.157361] serial 00:06: activated
[130755.424027] sd 6:0:0:0: [sda] Starting disk
[130755.468016] firewire_core: rediscovered device fw0
[130755.660015] firewire_core: rediscovered device fw1
[130755.760005] firewire_core: phy config: card 1, new root=ffc1, gap_count=5
[130758.762276] firewire_core: rediscovered device fw2
[130759.160279] firewire_sbp2: fw2.0: reconnected to LUN 0000 (0 retries)
[130759.180827] sd 2:0:0:0: [sdb] Starting disk
[130759.190839] sd 3:0:0:0: [sdc] Starting disk
[130759.201256] sd 4:0:0:0: [sdd] Starting disk
[130759.225759] hub 2-2:1.0: hub_port_status failed (err = -71)
[130759.226756] hub 2-2:1.0: hub_port_status failed (err = -71)
[130759.227755] hub 2-2:1.0: hub_port_status failed (err = -71)
[130759.228757] hub 2-2:1.0: hub_port_status failed (err = -71)
[130759.230756] hub 2-2:1.0: cannot disable port 3 (err = -71)
[130759.230782] pm_op(): usb_dev_restore+0x0/0xa [usbcore] returns -71
[130759.230784] PM: Device 2-2.3 failed to restore: error -71
[130759.345188] Restarting tasks ... <3>hub 2-2:1.0: hub_port_status failed
(err = -71)
[130759.412507] done.
[130763.005514] usb 2-2.3: USB disconnect, address 8
[130763.140021] usb 2-2: reset full speed USB device using uhci_hcd and address
4
[130763.581468] usb 2-2.3: new full speed USB device using uhci_hcd and address
9
[130763.737457] usb 2-2.3: New USB device found, idVendor=045e, idProduct=0714
[130763.737461] usb 2-2.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[130763.737464] usb 2-2.3: Product: Microsoft� Wireless Laser Mouse 8000
[130763.737467] usb 2-2.3: Manufacturer: Microsoft
[130763.737469] usb 2-2.3: SerialNumber: 00125A597FEF
[130763.737579] usb 2-2.3: configuration #1 chosen from 1 choice
[130763.753495] input: Microsoft Microsoft� Wireless Laser Mouse 8000 as
/devices/pci0000:00/0000:00:1a.0/usb2/2-2/2-2.3/2-2.3:1.0/input/input11
[130763.780144] generic-usb 0003:045E:0714.0009: input,hidraw3: USB HID v1.11
Mouse [Microsoft Microsoft� Wireless Laser Mouse 8000] on
usb-0000:00:1a.0-2.3/input0
[131458.961258] saa7130[0]/irq[10,32789740]: r=0x20 s=0x00 PE
[131458.961263] saa7130[0]/irq: looping -- clearing PE (parity error!) enable
bit
[135522.004109] usb 1-4.4: new high speed USB device using ehci_hcd and address
12
[135522.126595] usb 1-4.4: New USB device found, idVendor=0bc2, idProduct=2100
[135522.126600] usb 1-4.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[135522.126603] usb 1-4.4: Product: FreeAgent Go
[135522.126605] usb 1-4.4: Manufacturer: Seagate
[135522.126608] usb 1-4.4: SerialNumber: 2GE2H3QF
[135522.126720] usb 1-4.4: configuration #1 chosen from 1 choice
[135522.131631] scsi17 : SCSI emulation for USB Mass Storage devices
[135522.131809] usb-storage: device found at 12
[135522.131813] usb-storage: waiting for device to settle before scanning
[135527.129302] usb-storage: device scan complete
[135527.130788] scsi 17:0:0:0: Direct-Access Seagate FreeAgent Go 102D
PQ: 0 ANSI: 4
[135527.132893] sd 17:0:0:0: [sde] 976773168 512-byte hardware sectors: (500
GB/465 GiB)
[135527.134141] sd 17:0:0:0: [sde] Write Protect is off
[135527.134145] sd 17:0:0:0: [sde] Mode Sense: 1c 00 00 00
[135527.134148] sd 17:0:0:0: [sde] Assuming drive cache: write through
[135527.137044] sd 17:0:0:0: [sde] 976773168 512-byte hardware sectors: (500
GB/465 GiB)
[135527.143354] sd 17:0:0:0: [sde] Write Protect is off
[135527.143360] sd 17:0:0:0: [sde] Mode Sense: 1c 00 00 00
[135527.143362] sd 17:0:0:0: [sde] Assuming drive cache: write through
[135527.143368] sde: sde1
[135527.209729] sd 17:0:0:0: [sde] Attached SCSI disk
[135527.209827] sd 17:0:0:0: Attached scsi generic sg5 type 0
[135532.919924] kjournald starting. Commit interval 5 seconds
[135532.922873] EXT3 FS on sde1, internal journal
[135532.922880] EXT3-fs: mounted filesystem with ordered data mode.
[169665.556002] cdrom: This disc doesn't have any tracks I recognize!
[169665.596611] sr 5:0:0:0: [sr0] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE,SUGGEST_OK
[169665.596617] sr 5:0:0:0: [sr0] Sense Key : Illegal Request [current]
[169665.596623] sr 5:0:0:0: [sr0] Add. Sense: Logical block address out of range
[169665.596629] end_request: I/O error, dev sr0, sector 0
[169665.596633] Buffer I/O error on device sr0, logical block 0
[169665.599044] sr 5:0:0:0: [sr0] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE,SUGGEST_OK
[169665.599048] sr 5:0:0:0: [sr0] Sense Key : Illegal Request [current]
[169665.599053] sr 5:0:0:0: [sr0] Add. Sense: Logical block address out of range
[169665.599059] end_request: I/O error, dev sr0, sector 0
[169665.599062] Buffer I/O error on device sr0, logical block 0
[169677.431873] warning: `growisofs' uses 32-bit capabilities (legacy support
in use)
** Loaded modules:
Module Size Used by
snd_emu10k1_synth 5340 0
snd_emux_synth 27520 1 snd_emu10k1_synth
snd_seq_virmidi 4664 1 snd_emux_synth
snd_seq_midi_emul 5076 1 snd_emux_synth
nvidia 9533000 36
nls_utf8 1472 0
nls_cp437 5304 0
vfat 8672 0
fat 41688 1 vfat
nls_base 6508 4 nls_utf8,nls_cp437,vfat,fat
usblp 10384 0
usb_storage 83612 1
ppdev 6224 0
parport_pc 22104 0
lp 7872 0
parport 30868 3 ppdev,parport_pc,lp
rfcomm 29636 4
l2cap 17072 9 rfcomm
nfsd 186332 13
lockd 57840 1 nfsd
nfs_acl 2624 1 nfsd
auth_rpcgss 31344 1 nfsd
sunrpc 161964 13 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 3900 1 nfsd
acpi_cpufreq 7040 0
cpufreq_userspace 2748 0
cpufreq_stats 3588 0
cpufreq_conservative 5456 0
cpufreq_powersave 1276 0
microcode 11628 0
ipv6 232360 27
fuse 48352 1
vboxdrv 94328 0
coretemp 5160 0
f71882fg 19076 0
loop 12988 0
snd_usb_audio 71536 1
snd_usb_lib 13552 1 snd_usb_audio
tuner_simple 11468 1
tuner_types 13808 1 tuner_simple
tuner 21192 0
snd_emu10k1 115844 5 snd_emu10k1_synth
snd_ac97_codec 91260 1 snd_emu10k1
ac97_bus 1444 1 snd_ac97_codec
snd_pcm_oss 31708 0
snd_mixer_oss 12000 1 snd_pcm_oss
snd_pcm 62792 5
snd_usb_audio,snd_emu10k1,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 8104 2 snd_emu10k1,snd_pcm
snd_util_mem 3736 2 snd_emux_synth,snd_emu10k1
snd_seq_dummy 2368 0
snd_hwdep 6000 3 snd_emux_synth,snd_usb_audio,snd_emu10k1
snd_seq_oss 24756 0
snd_seq_midi 5448 0
snd_rawmidi 18544 4
snd_seq_virmidi,snd_usb_lib,snd_emu10k1,snd_seq_midi
snd_seq_midi_event 6072 3 snd_seq_virmidi,snd_seq_oss,snd_seq_midi
saa7134 132824 0
snd_seq 42120 10
snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
btusb 10160 2
ir_common 44856 1 saa7134
snd_timer 17808 3 snd_emu10k1,snd_pcm,snd_seq
snd_seq_device 6108 8
snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
v4l2_common 14508 2 tuner,saa7134
emu10k1_gp 2464 0
psmouse 36628 0
bluetooth 46052 7 rfcomm,l2cap,btusb
snd 48420 24
snd_emux_synth,snd_seq_virmidi,snd_usb_audio,snd_emu10k1,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_hwdep,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
videodev 33448 3 tuner,saa7134,v4l2_common
v4l1_compat 11196 1 videodev
videobuf_dma_sg 11224 1 saa7134
videobuf_core 16148 2 saa7134,videobuf_dma_sg
tveeprom 10592 1 saa7134
serio_raw 4544 0
gameport 10200 2 emu10k1_gp
iTCO_wdt 9896 0
i2c_i801 8108 0
pcspkr 2092 0
joydev 8560 0
evdev 8160 10
button 5672 0
soundcore 6204 1 snd
ext3 107180 6
jbd 42500 1 ext3
mbcache 7180 1 ext3
sg 19940 0
sr_mod 12840 0
cdrom 29804 1 sr_mod
hid_microsoft 3200 0
usbhid 29188 0
hid 34260 2 hid_microsoft,usbhid
sd_mod 28252 12
crc_t10dif 1616 1 sd_mod
firewire_sbp2 12748 1
ahci 27592 5
libata 149152 1 ahci
nvidiafb 37984 0
fb_ddc 1820 1 nvidiafb
i2c_algo_bit 4888 1 nvidiafb
vgastate 6548 1 nvidiafb
r8169 27928 0
firewire_ohci 18968 0
firewire_core 33564 2 firewire_sbp2,firewire_ohci
crc_itu_t 1796 1 firewire_core
scsi_mod 132076 6
usb_storage,sg,sr_mod,sd_mod,firewire_sbp2,libata
uhci_hcd 19472 0
ehci_hcd 30336 0
mii 4648 1 r8169
i2c_core 20828 10
nvidia,tuner_simple,tuner,saa7134,v4l2_common,tveeprom,i2c_i801,nvidiafb,fb_ddc,i2c_algo_bit
intel_agp 22740 0
usbcore 125168 9
usblp,usb_storage,snd_usb_audio,snd_usb_lib,btusb,usbhid,uhci_hcd,ehci_hcd
agpgart 30648 2 nvidia,intel_agp
thermal 15092 0
processor 39528 2 acpi_cpufreq,thermal
fan 4104 0
thermal_sys 10272 3 thermal,processor,fan
dm_mirror 12468 0
dm_region_hash 10632 1 dm_mirror
dm_log 8588 2 dm_mirror,dm_region_hash
dm_mod 48856 2 dm_mirror,dm_log
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller [8086:29c0] (rev 02)
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+ INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82G33/G31/P35/P31 Express PCI
Express Root Port [8086:29c1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fa000000-fe9fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at b880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f9fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 5 [8086:2948] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 6 [8086:294a] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at b800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at b480 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at b080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f9fff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IR (ICH9R) LPC Interface
Controller [8086:2916] (rev 02)
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6
port SATA AHCI Controller [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 29
Region 0: I/O ports at b000 [size=8]
Region 1: I/O ports at ac00 [size=4]
Region 2: I/O ports at a880 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at a480 [size=32]
Region 5: Memory at f9fff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller
[8086:2930] (rev 02)
Subsystem: Micro-Star International Co., Ltd. Device [1462:7345]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f9ffec00 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: nVidia Corporation G80 [GeForce 8800
GTS] [10de:0193] (rev a2) (prog-if 00 [VGA controller])
Subsystem: nVidia Corporation Device [10de:0421]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at cc00 [size=128]
[virtual] Expansion ROM at fe9e0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: Micro-Star International Co., Ltd. Device [1462:345c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at d800 [size=256]
Region 2: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
05:00.0 Multimedia audio controller [0401]: Creative Labs SB Audigy [1102:0004]
(rev 04)
Subsystem: Creative Labs SB Audigy 2 ZS (SB0350) [1102:2002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at ec00 [size=64]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
05:00.1 Input device controller [0980]: Creative Labs SB Audigy Game Port
[1102:7003] (rev 04)
Subsystem: Creative Labs SB Audigy Game Port [1102:0040]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at e880 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
05:00.2 FireWire (IEEE 1394) [0c00]: Creative Labs SB Audigy FireWire Port
[1102:4001] (rev 04) (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port [1102:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
05:01.0 Multimedia controller [0480]: Philips Semiconductors SAA7130 Video
Broadcast Decoder [1131:7130] (rev 01)
Subsystem: Animation Technologies Inc. LifeView FlyVIDEO2000 [5168:0138]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febff400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: saa7134
05:02.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306 Fire II IEEE
1394 OHCI Link Layer Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:345d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at febfe800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at e800 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.29-2-686-bigmem (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.29-2-686-bigmem depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.2 tools for generating an initramfs
ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.29-2-686-bigmem recommends:
ii libc6-i686 2.9-12 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.29-2-686-bigmem suggests:
ii grub-pc [grub] 1.96+20090523-1 GRand Unified Bootloader, version
ii linux-doc-2.6.29 2.6.29-5 Linux kernel specific documentatio
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.29-2-686-bigmem/prerm/would-invalidate-boot-loader-2.6.29-2-686-bigmem:
true
linux-image-2.6.29-2-686-bigmem/preinst/lilo-has-ramdisk:
linux-image-2.6.29-2-686-bigmem/postinst/bootloader-error-2.6.29-2-686-bigmem:
linux-image-2.6.29-2-686-bigmem/postinst/old-initrd-link-2.6.29-2-686-bigmem:
true
linux-image-2.6.29-2-686-bigmem/preinst/overwriting-modules-2.6.29-2-686-bigmem:
true
linux-image-2.6.29-2-686-bigmem/preinst/elilo-initrd-2.6.29-2-686-bigmem: true
linux-image-2.6.29-2-686-bigmem/postinst/kimage-is-a-directory:
linux-image-2.6.29-2-686-bigmem/preinst/bootloader-initrd-2.6.29-2-686-bigmem:
true
linux-image-2.6.29-2-686-bigmem/preinst/lilo-initrd-2.6.29-2-686-bigmem: true
linux-image-2.6.29-2-686-bigmem/postinst/create-kimage-link-2.6.29-2-686-bigmem:
true
linux-image-2.6.29-2-686-bigmem/preinst/abort-overwrite-2.6.29-2-686-bigmem:
linux-image-2.6.29-2-686-bigmem/preinst/failed-to-move-modules-2.6.29-2-686-bigmem:
linux-image-2.6.29-2-686-bigmem/postinst/bootloader-test-error-2.6.29-2-686-bigmem:
linux-image-2.6.29-2-686-bigmem/preinst/abort-install-2.6.29-2-686-bigmem:
linux-image-2.6.29-2-686-bigmem/postinst/old-dir-initrd-link-2.6.29-2-686-bigmem:
true
linux-image-2.6.29-2-686-bigmem/postinst/depmod-error-initrd-2.6.29-2-686-bigmem:
false
linux-image-2.6.29-2-686-bigmem/postinst/old-system-map-link-2.6.29-2-686-bigmem:
true
linux-image-2.6.29-2-686-bigmem/preinst/initrd-2.6.29-2-686-bigmem:
linux-image-2.6.29-2-686-bigmem/postinst/depmod-error-2.6.29-2-686-bigmem:
false
linux-image-2.6.29-2-686-bigmem/prerm/removing-running-kernel-2.6.29-2-686-bigmem:
true
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
