Package: installation-reports
Debian-installer-version: June 21, 12:00 AEST -
http://http.us.debian.org/dists/sarge/main/installer-sparc/current//images/sparc64/netboot/2.6/boot.img
uname -a: not available
Date: June 21 12:30 AEST
Method: Installed using tftp from laptop. Did Stop-A, then "boot net".
tftp server and rarp server setup on laptop, boot.img copied
to tftp directory, symlinked boot.img to C0A80101 (hex of
192.168.1.1). No proxy.
Machine: SUN SunBlade 1000
Processor: 900MHz UltraSparc-III
Memory: 2048Mb
Root Device: Root dev SCSI ( 2 x 73Gb FC drives)
Peripherals: USB Type 6 Mouse and Keyboard.
Root Size/partition table: See Below
Output of lspci and lspci -n:
beast # lspci
0000:00:00.0 Host bridge: Sun Microsystems Computer Corp. Schizo PCI Bus Module
0000:00:05.0 Bridge: Sun Microsystems Computer Corp. RIO EBUS (rev 01)
0000:00:05.1 Ethernet controller: Sun Microsystems Computer Corp. RIO GEM (rev 0
1)
0000:00:05.2 FireWire (IEEE 1394): Sun Microsystems Computer Corp. RIO 1394 (rev
01)
0000:00:05.3 USB Controller: Sun Microsystems Computer Corp. RIO USB (rev 01)
0000:00:06.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 37)
0000:00:06.1 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 37)
0000:01:00.0 Host bridge: Sun Microsystems Computer Corp. Schizo PCI Bus Module
0000:01:04.0 SCSI storage controller: QLogic Corp. QLA2200 64-bit Fibre Channel
Adapter (rev 05)
beast # lspci -n
0000:00:00.0 Class 0600: 108e:8001
0000:00:05.0 Class 0680: 108e:1100 (rev 01)
0000:00:05.1 Class 0200: 108e:1101 (rev 01)
0000:00:05.2 Class 0c00: 108e:1102 (rev 01)
0000:00:05.3 Class 0c03: 108e:1103 (rev 01)
0000:00:06.0 Class 0100: 1000:000f (rev 37)
0000:00:06.1 Class 0100: 1000:000f (rev 37)
0000:01:00.0 Class 0600: 108e:8001
0000:01:04.0 Class 0100: 1077:2200 (rev 05)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [E]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
My appologies if this list is long and boring, but here's what
happened.
1. Booted OK from boot.img via "boot net"
2. Installer downloaded and started hardware detection - attempted to
install qlogicisp module - incorrect, as qlogicfc is needed.
3. manually did "modprobe -v qlogicfc" - short delay, module loaded.
4. detected both disks OK, used auto-partitioning as multi-user
workstation. Only partitioned a total of 18Gb of the drive. No free
space evident.
5. manually partitioned the second drive as /home, same space problem
(suspect incorrect drive geometery or LBA support)
6. Installed base system.
7. rebooted.
8. Get message "remapping the kernel", then "fast data access mmu
miss", then back to the "ok" prompt.
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
