Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-13
Severity: normal
Dear Maintainers,
the RealTek RTL-8169 Gigabit Ethernet driver (r8169.ko) doesn't work
properly with icmp6.
I can't see any incoming icmp6 neighbor solicitation with tcpdump. But,
when I switch the interface in allmulticast mode:
ip set link allmulticast on dev eth0
everythink works. I can see icmp6 neighbor solicitations and appropriate
neighbor advertisements.
Is there some hardware limitation or is this a driver bug?
(Mainboard is an Asus M3A78 PRO)
Regards
Friedemann
-- Package-specific info:
** Version:
Linux version 2.6.26-1-amd64 (Debian 2.6.26-13) (wa...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 17:57:00 UTC
2009
** Command line:
root=/dev/md0 ro
** Not tainted
** Kernel log:
[ 6.494554] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[ 6.494611] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) ->
IRQ 18
[ 6.494694] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 6.494976] eth0: RTL8168c/8111c at 0xffffc20000c38000, 00:22:15:fd:b1:0d,
XID 3c4000c0 IRQ 1277
[ 36.801716] r8169: eth0: link up
[ 36.805223] r8169: eth0: link up
** Loaded modules:
Module Size Used by
sg 36448 0
kvm_amd 29580 0
kvm 127464 1 kvm_amd
ip6t_REJECT 8320 2
xt_NFLOG 6400 2
ip6table_filter 7296 1
ip6_tables 23056 1 ip6table_filter
xt_tcpudp 7680 1
ipt_REJECT 7552 2
ipt_ULOG 13736 3
iptable_filter 7424 1
ip_tables 21520 1 iptable_filter
x_tables 25224 7
ip6t_REJECT,xt_NFLOG,ip6_tables,xt_tcpudp,ipt_REJECT,ipt_ULOG,ip_tables
nfsd 248360 17
auth_rpcgss 47520 1 nfsd
exportfs 8704 1 nfsd
nfs 251696 0
lockd 68560 2 nfsd,nfs
nfs_acl 7552 2 nfsd,nfs
sunrpc 197480 14 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
bridge 53544 0
xfs 475432 7
aes_x86_64 12416 4
aes_generic 32552 1 aes_x86_64
xts 7680 2
gf128mul 12800 1 xts
dm_crypt 17032 1
crypto_blkcipher 21636 4 xts,dm_crypt
ipv6 288328 67 ip6t_REJECT
loop 19468 0
snd_hda_intel 434904 0
serio_raw 9860 0
pcspkr 7040 0
psmouse 42268 0
k8temp 9216 0
snd_pcm 81672 1 snd_hda_intel
snd_timer 25744 1 snd_pcm
snd 63688 3 snd_hda_intel,snd_pcm,snd_timer
soundcore 12064 1 snd
snd_page_alloc 13072 2 snd_hda_intel,snd_pcm
i2c_piix4 13072 0
i2c_core 27936 1 i2c_piix4
wmi 11712 0
button 11680 0
shpchp 34080 0
pci_hotplug 32056 1 shpchp
evdev 14208 0
ext3 125072 5
jbd 51240 1 ext3
mbcache 12804 1 ext3
dm_mirror 20608 0
dm_log 13956 1 dm_mirror
dm_snapshot 19400 0
dm_mod 58864 31 dm_crypt,dm_mirror,dm_log,dm_snapshot
raid456 125984 1
async_xor 8448 1 raid456
async_memcpy 6912 1 raid456
async_tx 11764 3 raid456,async_xor,async_memcpy
xor 9744 2 raid456,async_xor
raid1 24192 3
md_mod 80164 6 raid456,raid1
usb_storage 94528 0
ata_generic 10116 0
ide_pci_generic 9220 0 [permanent]
atiixp 8324 0 [permanent]
ide_core 128284 2 ide_pci_generic,atiixp
ehci_hcd 36108 0
ohci_hcd 25092 0
r8169 31492 0
sd_mod 29376 12
thermal 22688 0
processor 42304 1 thermal
fan 9352 0
thermal_sys 17728 3 thermal,processor,fan
ahci 33036 16
libata 165472 2 ata_generic,ahci
scsi_mod 160760 4 sg,usb_storage,sd_mod,libata
dock 14112 1 libata
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge
[1022:9600]
Subsystem: ATI Technologies Inc Device [1002:7910]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge
(int gfx) [1022:9602] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe900000-feafffff
Prefetchable memory behind bridge: 00000000fa000000-00000000fbffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge
(PCIE port 2) [1022:9606] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA
Controller [AHCI mode] [1002:4391] (prog-if 01 [AHCI 1.0])
Subsystem: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode]
[1002:4391]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 1278
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at b000 [size=4]
Region 2: I/O ports at a000 [size=8]
Region 3: I/O ports at 9000 [size=4]
Region 4: I/O ports at 8000 [size=16]
Region 5: Memory at fe8ff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0
Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
[1002:4397]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe8fe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller
[1002:4398] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe8fd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI
Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ATI Technologies Inc Device [1002:4397]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0
Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc Device [1002:4398]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe8fc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller
[1002:4398] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc Device [1002:4399]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe8fb000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI
Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ATI Technologies Inc SB700/SB800 USB EHCI Controller
[1002:4396]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe8fa800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385]
(rev 3a)
Subsystem: ASUSTeK Computer Inc. Device [1043:82f1]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort+ <MAbort- >SERR+ <PERR+ INTx-
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller
[1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:82f1]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ff00 [size=16]
Capabilities: <access denied>
Kernel driver in use: ATIIXP_IDE
Kernel modules: ide-pci-generic, atiixp, ata_generic
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA)
[1002:4383]
Subsystem: ASUSTeK Computer Inc. Device [1043:82fe]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at fe8f4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller
[1002:439d]
Subsystem: ATI Technologies Inc Device [1002:4383]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge
[1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2
Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc Device [1002:4396]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe8f9000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon HD 3200
Graphics [1002:9610] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:82f1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fa000000 (32-bit, prefetchable) [size=32M]
Region 1: I/O ports at d000 [size=256]
Region 2: Memory at feaf0000 (32-bit, non-prefetchable) [size=64K]
Region 5: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:82c6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 1277
Region 0: I/O ports at e800 [size=256]
Region 2: Memory at febff000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fdff0000 (64-bit, prefetchable) [size=64K]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
-- System Information:
Debian Release: 5.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information excluded
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
