Hi
Don't remember which parts were updated...
There is -ddd output in attached file
With regards
Jakub
On Sat, Jun 14, 2008 at 2:10 AM, Kel Modderman <[EMAIL PROTECTED]> wrote:
> On Thursday 12 June 2008 16:37:03 Jakub Lucký wrote:
>> Even downgrading to Etch version wasn't succesful, so maybe there is
>> problem in some library?
>
> s/Etch/Lenny/ ?
>
> Did you observe what other parts of your system were updated along with new
> wpasupplicant package?
>
>>
>> Jakub
>>
>> P.S. am I alone with this bug, or is it common?
>
> Noone else has reported a similar issue yet.
>
> Thanks, Kel.
>
Initializing interface 'wlan0' conf '/etc/wpa_supplicat.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicat.conf' -> '/etc/wpa_supplicat.conf'
Reading configuration file '/etc/wpa_supplicat.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='0' (DEPRECATED)
eapol_version=1
ap_scan=1
fast_reauth=1
Line: 6 - start of a new network block
ssid - hexdump_ascii(len=3):
47 4a 4b GJK
key_mgmt: 0x1
eap methods - hexdump(len=16): 00 00 00 00 15 00 00 00 00 00 00 00 00 00 00 00
anonymous_identity - hexdump_ascii(len=7):
78 6c 75 63 6a 30 31 xlucj01
identity - hexdump_ascii(len=7):
78 6c 75 63 6a 30 31 xlucj01
password - hexdump_ascii(len=8):
65 61 62 36 37 34 63 65 eab674ce
priority=2 (0x2)
phase2 - hexdump_ascii(len=8):
61 75 74 68 3d 50 41 50 auth=PAP
Priority group 2
id=0 ssid='GJK'
Initializing interface (2) 'wlan0'
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:13:e8:a5:6a:8d
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Using existing control interface directory.
ctrl_interface_group=0
ctrl_iface bind(PF_UNIX) failed: Address already in use
ctrl_iface exists, but does not allow connections - assuming it was leftover from forced program termination
Successfully replaced leftover ctrl_iface socket '/var/run/wpa_supplicant/wlan0'
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=12
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Invalid freq in scan results (BSSID=00:00:01:00:00:c0 m=0 e=20192)
Invalid freq in scan results (BSSID=00:00:01:00:00:c0 m=0 e=8)
