Package: linux-image-2.6.22-3-686
Version: 2.6.22-6.lenny1
Severity: important
There seems to be random reading errors when reading from my Seagate FreeAgent
500GB external USB hard drive. It becomes clear by an example:
# md5sum -c test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum -c
test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum
-c test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum -c test02.avi.md5
test02.avi: OK
test02.avi: FAILED
md5sum: WARNING: 1 of 1 computed checksum did NOT match
test02.avi: OK
test02.avi: OK
test02.avi: OK
test02.avi: OK
test02.avi: OK
test02.avi: FAILED
md5sum: WARNING: 1 of 1 computed checksum did NOT match
test02.avi is a file on device sda3 from the kernel log. When issuing a rmmod
ehci_hcd, the same command returns OK every time.
Please let me know if I can be of any help. I would really like to see this
issue resolved.
-- Package-specific info:
** Version:
Linux version 2.6.22-3-686 (Debian 2.6.22-6.lenny1) ([EMAIL PROTECTED]) (gcc
version 4.1.3 20071209 (prerelease) (Debian 4.1.2-18)) #1 SMP Sun Feb 10
20:20:49 UTC 2008
** Not tainted
** Kernel log:
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
r8169: eth0: link up
eth0: no IPv6 routers present
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ehci_hcd 0000:02:06.2: remove, state 1
usb usb7: USB disconnect, address 1
usb 7-3: USB disconnect, address 2
ehci_hcd 0000:02:06.2: USB bus 7 deregistered
ACPI: PCI interrupt for device 0000:02:06.2 disabled
usb 6-1: new full speed USB device using uhci_hcd and address 3
usb 6-1: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access Seagate FreeAgentDesktop 100F PQ: 0 ANSI: 4
sd 4:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 1c 00 00 00
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 1c 00 00 00
sd 4:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 4:0:0:0: [sda] Attached SCSI disk
** Loaded modules:
Module Size Used by
ehci_hcd 30796 0
binfmt_misc 11112 1
rfcomm 36280 2
l2cap 22432 9 rfcomm
bluetooth 49348 4 rfcomm,l2cap
ppdev 8676 0
lp 10980 0
ipv6 236964 16
firewire_sbp2 12100 0
loop 16932 0
sd_mod 27136 2
snd_intel8x0 32124 1
snd_ac97_codec 92836 1 snd_intel8x0
usblp 13280 0
parport_pc 33828 1
ac97_bus 2272 1 snd_ac97_codec
snd_pcm_oss 39200 0
snd_mixer_oss 15424 1 snd_pcm_oss
parport 33928 3 ppdev,lp,parport_pc
snd_pcm 72324 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 21028 1 snd_pcm
snd 48324 8
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 7520 1 snd
snd_page_alloc 10056 2 snd_intel8x0,snd_pcm
rtc 12856 0
i2c_i801 8656 0
i2c_core 23552 1 i2c_i801
iTCO_wdt 9924 0
intel_agp 23188 1
agpgart 31880 1 intel_agp
shpchp 31060 0
pci_hotplug 29184 1 shpchp
tsdev 7968 0
evdev 9312 1
ext3 121288 3
jbd 55336 1 ext3
mbcache 8260 1 ext3
ide_cd 36416 0
cdrom 32832 1 ide_cd
ide_disk 16512 5
ata_generic 7556 0
ata_piix 13348 0
libata 115984 2 ata_generic,ata_piix
usb_storage 76576 1
scsi_mod 136620 4 firewire_sbp2,sd_mod,libata,usb_storage
usbhid 25792 0
hid 25248 1 usbhid
floppy 54884 0
generic 4836 0 [permanent]
piix 8868 0 [permanent]
ide_core 113764 5 ide_cd,ide_disk,usb_storage,generic,piix
firewire_ohci 16512 0
firewire_core 39008 2 firewire_sbp2,firewire_ohci
crc_itu_t 2144 1 firewire_core
r8169 28872 0
uhci_hcd 22960 0
usbcore 125384 6 ehci_hcd,usblp,usb_storage,usbhid,uhci_hcd
thermal 13416 0
processor 31176 1 thermal
fan 4836 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM
Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P PCI to AGP Controller
[8086:2571] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at b000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b400 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 30000000-300fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
Region 5: Memory at 30100000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller
[8086:24d1] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at c400 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at cc00 [size=4]
Region 4: I/O ports at d000 [size=16]
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller [8086:24d3] (rev 02)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc00 [size=64]
Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at fc001000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV34 [GeForce FX
5200] [10de:0322] (rev a1) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at f9000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: nvidiafb
02:02.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 30000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
02:06.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
02:06.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at a800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
02:06.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev
63) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fb001000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
02:06.3 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. IEEE 1394 Host
Controller [1106:3044] (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller [1106:3044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fb002000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ac00 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-3-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-3-686 depends on:
ii initramfs-tools [linux-initr 0.91e tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.22-3-686 recommends:
ii libc6-i686 2.7-6 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.22-3-686/postinst/bootloader-test-error-2.6.22-3-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-3-686/preinst/lilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/would-invalidate-boot-loader-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/overwriting-modules-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/elilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/kimage-is-a-directory:
linux-image-2.6.22-3-686/preinst/lilo-has-ramdisk:
linux-image-2.6.22-3-686/postinst/old-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/initrd-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-system-map-link-2.6.22-3-686: true
* linux-image-2.6.22-3-686/preinst/already-running-this-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-2.6.22-3-686: false
linux-image-2.6.22-3-686/postinst/bootloader-error-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/failed-to-move-modules-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-dir-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/abort-install-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/abort-overwrite-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-initrd-2.6.22-3-686: false
linux-image-2.6.22-3-686/preinst/bootloader-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/removing-running-kernel-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/create-kimage-link-2.6.22-3-686: true
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
