Package: installation-reports Package: installation-reports Package: installation-reports Package: installation-reports
hi. This references an debian sarge install on a Thinkpad with a xircom RBE-100 nic. this hardware works fine on other MS os's, so i dont suspect hardware failure. Package: installation-reports Debian-installer-version: debian sarge most likely from http://cdimage.debian.org/pub/weekly/i386/ uname -a: not captured, but chose linux26 and expert26 during install. Date: May 7, 8, 9 and 10th! Method: booted from sarge cd Machine: IBM THinkpad iSeries, 2611 Processor: Mobile Pentium MMX 266 Memory: 256megs Root Device: ide, 20gigs Root Size/partition table: default "All files on one partition", plus swap part Output of lspci and lspci -n: 0000:00:00.0 Host bridge: ALi Corporation M1531 [Aladdin IV] (rev b3) Subsystem: ALi Corporation M1531 [Aladdin IV] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 32 0000:00:02.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] (rev 0a) Subsystem: ALi Corporation ALI M1533 Aladdin IV ISA Bridge Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort+ >SERR- <PERR- Latency: 0 0000:00:05.0 CardBus bridge: O2 Micro, Inc. OZ6832/6833 Cardbus Controller (rev 34) Subsystem: O2 Micro, Inc. OZ6832/6833 Cardbus Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 9 Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=01, subordinate=04, sec-latency=176 Memory window 0: 10400000-107ff000 (prefetchable) Memory window 1: 10800000-10bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 0000:00:05.1 CardBus bridge: O2 Micro, Inc. OZ6832/6833 Cardbus Controller (rev 34) Subsystem: O2 Micro, Inc. OZ6832/6833 Cardbus Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 168 Interrupt: pin B routed to IRQ 9 Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=05, subordinate=08, sec-latency=176 Memory window 0: 10c00000-10fff000 (prefetchable) Memory window 1: 12400000-127ff000 I/O window 0: 00004800-000048ff I/O window 1: 00004c00-00004cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+ 16-bit legacy interface ports at 0001 0000:00:06.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01) (prog-if 00 [VGA]) Subsystem: Unknown device 0004:10c8 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 9 Region 0: Memory at 11000000 (32-bit, prefetchable) [size=16M] Region 1: Memory at 12000000 (32-bit, non-prefetchable) [size=2M] Region 2: Memory at 12200000 (32-bit, non-prefetchable) [size=1M] 0000:00:0b.0 IDE interface: ALi Corporation M5229 IDE (rev 20) (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 1000ns max) Interrupt: pin A routed to IRQ 15 Region 4: I/O ports at 6090 [size=16] 0000:00:0c.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU] (rev 09) Subsystem: ALi Corporation: Unknown device 1533 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 0000:05:00.0 Ethernet controller: Xircom Cardbus Ethernet 10/100 (rev 03) Subsystem: Xircom Cardbus Ethernet 10/100 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (5000ns min, 10000ns max) Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at 4800 [size=128] Region 1: Memory at 12400000 (32-bit, non-prefetchable) [size=2K] Region 2: Memory at 12400800 (32-bit, non-prefetchable) [size=2K] Expansion ROM at 10c00000 [disabled] [size=16K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [ o] Configure network HW: [ o] Config network: [ E] Detect CD: [ o] Load installer modules: [ o] Detect hard drives: [o ] Partition hard drives: [ o] Create file systems: [o ] Mount partitions: [o ] Install base system: [o ] Install boot loader: [o ] Reboot: [o ] Comments/Problems: The debian sarge installer detected my xircom RBE-100 fine during install and got DHCP ip assigned via my Netgear router. During install i went to tty2 to confirm ip and it was correct. Install proceeded fine, however, upon reboot, card was detected, configured and was awaiting DHCP ip, but never got one. dhclient eth0 tries x number of times, but never gets an answer. Static IP does not seem to work either. My guess is, installer is using generic pcmcia or xircom driver, but upon reboot it uses a more specific one, which just doesnt work. please advise: Mike [EMAIL PROTECTED] __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
