----- Forwarded message from Philippe Bourcier <[EMAIL PROTECTED]> -----
X-Original-To: [EMAIL PROTECTED]
Date: Sat, 9 Apr 2005 20:51:37 +0200
From: Philippe Bourcier <[EMAIL PROTECTED]>
To: maximilian attems <[EMAIL PROTECTED]>
Subject: Re: Bug#303550: kernel-image-2.6.11-1-686: irq11 makes eth0 problems
hi Maximilian,
first, thanks a lot for looking to this problem
On Fri, Apr 08, 2005 at 06:34:48PM +0200, maximilian attems wrote:
> tags 303550 moreinfo
> On Thu, 07 Apr 2005, Philippe BOURCIER wrote:
>
> > Apr 6 19:54:47 ile kernel: Linux version 2.6.11-1-686 ([EMAIL PROTECTED])
> > (gcc version 3.3.5 (Debian 1:3.3.5-8)) #1 Sun Apr 3 06:20:48 EDT 2005
> > Apr 6 19:55:15 ile kernel: eth0: flipped to 10baseT
> > Apr 6 19:55:19 ile kernel: irq 11: nobody cared!
> > Apr 6 19:55:19 ile kernel: [<c013242a>] __report_bad_irq+0x2a/0xa0
> > Apr 6 19:55:19 ile kernel: [<c0131ed0>] handle_IRQ_event+0x30/0x70
> > Apr 6 19:55:19 ile kernel: [<c0132530>] note_interrupt+0x70/0xb0
> > Apr 6 19:55:19 ile kernel: [<c0131ff0>] __do_IRQ+0xe0/0xf0
> > Apr 6 19:55:19 ile kernel: [<c0105279>] do_IRQ+0x19/0x30
> > Apr 6 19:55:19 ile kernel: [<c010391a>] common_interrupt+0x1a/0x20
> > Apr 6 19:55:19 ile kernel: [<c011cb6e>] __do_softirq+0x2e/0x90
> > Apr 6 19:55:19 ile kernel: [<c011cbf6>] do_softirq+0x26/0x30
> > Apr 6 19:55:19 ile kernel: [<c010527e>] do_IRQ+0x1e/0x30
> > Apr 6 19:55:19 ile kernel: [<c010391a>] common_interrupt+0x1a/0x20
> > Apr 6 19:55:19 ile kernel: handlers:
> > Apr 6 19:55:19 ile kernel: [<c8cd1980>] (usb_hcd_irq+0x0/0x70 [usbcore])
> > Apr 6 19:55:19 ile kernel: [<c8cc48a0>] (yenta_interrupt+0x0/0x40
> > [yenta_socket])
> > Apr 6 19:55:19 ile kernel: [<c8cc48a0>] (yenta_interrupt+0x0/0x40
> > [yenta_socket])
> > Apr 6 19:55:19 ile kernel: Disabling IRQ #11
> > Apr 6 19:55:19 ile kernel: eth0: interrupt(s) dropped!
> > Apr 6 19:55:24 ile kernel: eth0: no IPv6 routers present
sometimes, i got that one :
Apr 9 19:45:29 ile kernel: Linux Kernel Card Services
Apr 9 19:45:29 ile kernel: options: [pci] [cardbus] [pm]
Apr 9 19:45:29 ile kernel: PCI: Found IRQ 11 for device 0000:00:03.0
Apr 9 19:45:29 ile kernel: Yenta: CardBus bridge found at 0000:00:03.0
[0000:0000]
Apr 9 19:45:29 ile kernel: Yenta: Using CSCINT to route CSC interrupts to PCI
Apr 9 19:45:29 ile kernel: Yenta: Routing CardBus interrupts to PCI
Apr 9 19:45:29 ile kernel: Yenta TI: socket 0000:00:03.0, mfunc 0xcba97543,
devctl 0x62
Apr 9 19:45:29 ile kernel: irq 11: nobody cared!
Apr 9 19:45:29 ile kernel: [<c013242a>] __report_bad_irq+0x2a/0xa0
Apr 9 19:45:29 ile kernel: [<c0131ed0>] handle_IRQ_event+0x30/0x70
Apr 9 19:45:29 ile kernel: [<c0132530>] note_interrupt+0x70/0xb0
Apr 9 19:45:29 ile kernel: [<c0131ff0>] __do_IRQ+0xe0/0xf0
Apr 9 19:45:29 ile kernel: [<c0105279>] do_IRQ+0x19/0x30
Apr 9 19:45:29 ile kernel: [<c010391a>] common_interrupt+0x1a/0x20
Apr 9 19:45:29 ile kernel: [<c011cb6e>] __do_softirq+0x2e/0x90
Apr 9 19:45:29 ile kernel: [<c011cbf6>] do_softirq+0x26/0x30
Apr 9 19:45:29 ile kernel: [<c010527e>] do_IRQ+0x1e/0x30
Apr 9 19:45:29 ile kernel: [<c010391a>] common_interrupt+0x1a/0x20
Apr 9 19:45:29 ile kernel: [<c01bb294>] pci_bus_write_config_word+0x54/0x60
Apr 9 19:45:29 ile kernel: [<c8cc64db>] yenta_probe_cb_irq+0x6b/0x130
[yenta_socket]
Apr 9 19:45:29 ile kernel: [<c0118507>] printk+0x17/0x20
Apr 9 19:45:29 ile kernel: [<c8cc5461>] ti12xx_irqroute_func0+0x91/0x390
[yenta_socket]
Apr 9 19:45:29 ile kernel: [<c8cc5c3f>] ti12xx_override+0xff/0x1b0
[yenta_socket]
Apr 9 19:45:29 ile kernel: [<c8cc5d7f>] ti1250_override+0x8f/0xa0
[yenta_socket]
Apr 9 19:45:29 ile kernel: [<c8cc69a0>] yenta_probe+0x220/0x250 [yenta_socket]
Apr 9 19:45:29 ile kernel: [<c01bf402>] pci_device_probe_static+0x52/0x70
Apr 9 19:45:29 ile kernel: [<c01bf45c>] __pci_device_probe+0x3c/0x50
Apr 9 19:45:29 ile kernel: [<c01bf49c>] pci_device_probe+0x2c/0x50
Apr 9 19:45:29 ile kernel: [<c0211a4f>] driver_probe_device+0x2f/0x80
Apr 9 19:45:29 ile kernel: [<c0211b9c>] driver_attach+0x5c/0xa0
Apr 9 19:45:29 ile kernel: [<c02120ed>] bus_add_driver+0x9d/0xd0
Apr 9 19:45:29 ile kernel: [<c021270f>] driver_register+0x2f/0x40
Apr 9 19:45:29 ile kernel: [<c01bf714>] pci_register_driver+0x64/0x90
Apr 9 19:45:29 ile kernel: [<c8c8300f>] yenta_socket_init+0xf/0x11
[yenta_socket]
Apr 9 19:45:29 ile kernel: [<c012f6b2>] sys_init_module+0x122/0x1b0
Apr 9 19:45:29 ile kernel: [<c0102f33>] syscall_call+0x7/0xb
Apr 9 19:45:29 ile kernel: handlers:
Apr 9 19:45:29 ile kernel: [<c8cd1980>] (usb_hcd_irq+0x0/0x70 [usbcore])
Apr 9 19:45:29 ile kernel: Disabling IRQ #11
Apr 9 19:45:29 ile kernel: Yenta TI: socket 0000:00:03.0 probing PCI interrupt
failed, trying to fix
Apr 9 19:45:29 ile kernel: Yenta TI: socket 0000:00:03.0 no PCI interrupts.
Fish. Please report.
Apr 9 19:45:29 ile kernel: Yenta: ISA IRQ mask 0x0690, PCI irq 0
Apr 9 19:45:29 ile kernel: Socket status: 30000019
Apr 9 19:45:29 ile kernel: PCI: Found IRQ 11 for device 0000:00:03.1
Apr 9 19:45:29 ile kernel: Yenta: CardBus bridge found at 0000:00:03.1
[0000:0000]
Apr 9 19:45:29 ile kernel: Yenta: Using CSCINT to route CSC interrupts to PCI
Apr 9 19:45:29 ile kernel: Yenta: Routing CardBus interrupts to PCI
Apr 9 19:45:29 ile kernel: Yenta TI: socket 0000:00:03.1, mfunc 0xcba97543,
devctl 0x62
Apr 9 19:45:29 ile kernel: Yenta TI: socket 0000:00:03.1 probing PCI interrupt
failed, trying to fix
Apr 9 19:45:29 ile kernel: Yenta TI: socket 0000:00:03.1 no PCI interrupts.
Fish. Please report.
Apr 9 19:45:29 ile kernel: Yenta: ISA IRQ mask 0x0698, PCI irq 0
Apr 9 19:45:29 ile kernel: Socket status: 30000059
Apr 9 19:45:29 ile kernel: usb 1-1: grep timed out on ep0in
Apr 9 19:45:29 ile kernel: usb 1-1: grep timed out on ep0in
Apr 9 19:45:29 ile kernel: usb 1-1: string descriptor 0 read error: -110
> please send the following info of your box:
> * lspci -vv
> * cat /proc/interrupts
with 2.6.11:
------------
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
(AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at <unassigned> (32-bit, prefetchable)
0000:00:02.0 VGA compatible controller: S3 Inc. ViRGE/MX+MV (rev 03) (prog-if
00 [VGA])
Subsystem: S3 Inc. ViRGE/MX+MV
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at 000c0000 [disabled] [size=64K]
Capabilities: <available only to root>
0000:00:03.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 08000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 08400000-087ff000 (prefetchable)
Memory window 1: 08800000-08bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:03.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 08001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 08c00000-08fff000 (prefetchable)
Memory window 1: 09000000-093ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 1100 [size=16]
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 240
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at f300 [size=32]
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
and:
CPU0
0: 534058 XT-PIC timer
1: 798 XT-PIC i8042
2: 0 XT-PIC cascade
3: 17 XT-PIC 1.0
5: 1 XT-PIC soundblaster
7: 4 XT-PIC parport0
8: 1 XT-PIC rtc
9: 350 XT-PIC aha152x
11: 200000 XT-PIC uhci_hcd
12: 100 XT-PIC i8042
14: 7186 XT-PIC ide0
15: 27 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
with 2.6.10:
------------
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
(AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at <unassigned> (32-bit, prefetchable)
0000:00:02.0 VGA compatible controller: S3 Inc. ViRGE/MX+MV (rev 03) (prog-if
00 [VGA])
Subsystem: S3 Inc. ViRGE/MX+MV
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at 000c0000 [disabled] [size=64K]
Capabilities: <available only to root>
0000:00:03.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:03.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 1100 [size=16]
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 240
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at f300 [size=32]
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
and:
CPU0
0: 321422 XT-PIC timer
1: 404 XT-PIC i8042
2: 0 XT-PIC cascade
3: 350 XT-PIC aha152x
5: 1 XT-PIC soundblaster
7: 4 XT-PIC parport0
8: 1 XT-PIC rtc
9: 15 XT-PIC 3c589_cs
11: 412 XT-PIC uhci_hcd, yenta, yenta
12: 65 XT-PIC i8042
14: 6749 XT-PIC ide0
15: 1388 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
with 2.4.27:
------------
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
(AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at <unassigned> (32-bit, prefetchable) [size=256M]
0000:00:02.0 VGA compatible controller: S3 Inc. ViRGE/MX+MV (rev 03) (prog-if
00 [VGA])
Subsystem: S3 Inc. ViRGE/MX+MV
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at 000c0000 [disabled] [size=64K]
Capabilities: <available only to root>
0000:00:03.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:03.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 1100 [size=16]
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 240
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at f300 [size=32]
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
and:
CPU0
0: 55154 XT-PIC timer
1: 887 XT-PIC keyboard
2: 0 XT-PIC cascade
3: 769 XT-PIC aha152x
5: 1 XT-PIC soundblaster
8: 4 XT-PIC rtc
9: 76 XT-PIC 3c589_cs
11: 4702 XT-PIC usb-uhci, Texas Instruments PCI1250, Texas
Instruments PCI1250 (#2)
12: 17 XT-PIC PS/2 Mouse
14: 12844 XT-PIC ide0
15: 20 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
and:
$ uname -a ;sudo lshw
Linux ile 2.4.27-2-686 #1 Fri Mar 25 11:48:59 JST 2005 i686 GNU/Linux
ile
description: Computer
width: 32 bits
*-core
description: Motherboard
physical id: 0
*-memory
description: System memory
physical id: 1
size: 128MB
*-cpu
product: Pentium II (Deschutes)
vendor: Intel Corp.
physical id: 2
bus info: [EMAIL PROTECTED]
version: 6.5.2
size: 300MHz
width: 32 bits
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 sep
mtrr pge mca cmov pat pse36 mmx fxsr
*-cache:0
description: L1 cache
physical id: 0
size: 32KB
*-cache:1
description: L2 cache
physical id: 1
size: 512KB
*-pci
description: Host bridge
product: 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled)
vendor: Intel Corp.
physical id: 0
bus info: [EMAIL PROTECTED]:00.0
version: 02
width: 32 bits
clock: 33MHz
*-display
description: VGA compatible controller
product: ViRGE/MX+MV
vendor: S3 Inc.
physical id: 2
bus info: [EMAIL PROTECTED]:02.0
logical name: /dev/fb0
version: 03
size: 64MB
width: 32 bits
clock: 33MHz
capabilities: vga bus_master cap_list fb
configuration: depth=16 frequency=75.69Hz mode=1024x768
visual=truecolor xres=1024 yres=768
resources: iomemory:c0000000-c3ffffff
*-pcmcia:0
description: CardBus bridge
product: PCI1250
vendor: Texas Instruments
physical id: 3
bus info: [EMAIL PROTECTED]:03.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pcmcia bus_master cap_list
configuration: driver=cardbus
resources: iomemory:10000000-10000fff irq:11
*-pccard UNCLAIMED
description: APA-1460 SCSI Host Adapter
vendor: Adaptec, Inc.
physical id: 0
version: Version 0.01
slot: Socket 0
resources: irq:3
*-pcmcia:1
description: CardBus bridge
product: PCI1250
vendor: Texas Instruments
physical id: 3.1
bus info: [EMAIL PROTECTED]:03.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: pcmcia bus_master cap_list
configuration: driver=cardbus
resources: iomemory:10001000-10001fff irq:11
*-pccard UNCLAIMED
description: Megahertz 3CXEM556
product: LAN + 56k Modem
vendor: 3Com
physical id: 0
slot: Socket 1
resources: irq:9 irq:9
*-isa UNCLAIMED
description: ISA bridge
product: 82371AB/EB/MB PIIX4 ISA
vendor: Intel Corp.
physical id: 7
bus info: [EMAIL PROTECTED]:07.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: isa bus_master
*-ide
description: IDE interface
product: 82371AB/EB/MB PIIX4 IDE
vendor: Intel Corp.
physical id: 7.1
bus info: [EMAIL PROTECTED]:07.1
version: 01
width: 32 bits
clock: 33MHz
capabilities: ide bus_master
configuration: driver=PIIX IDE
resources: ioport:3000-300f
*-ide:0
description: IDE Channel 0
physical id: 0
bus info: [EMAIL PROTECTED]
logical name: ide0
clock: 33MHz
*-disk
description: ATA Disk
product: IBM-DBCA-206480
vendor: IBM
physical id: 0
bus info: [EMAIL PROTECTED]
logical name: /dev/hda
version: BC4OA87F
serial: HR0HRN20036
size: 6194MB
capacity: 6194MB
capabilities: ata dma lba iordy smart security pm apm
configuration: apm=off mode=udma2 smart=on
*-ide:1
description: IDE Channel 1
physical id: 1
bus info: [EMAIL PROTECTED]
logical name: ide1
clock: 33MHz
*-cdrom
description: IDE CD-ROM
product: TOSHIBA CD-ROM XM-1802B
vendor: Toshiba
physical id: 0
bus info: [EMAIL PROTECTED]
logical name: /dev/hdc
version: 1119
capabilities: packet atapi cdrom removable nonmagnetic dma
lba iordy audio
*-usb
description: USB Controller
product: 82371AB/EB/MB PIIX4 USB
vendor: Intel Corp.
physical id: 7.2
bus info: [EMAIL PROTECTED]:07.2
version: 01
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=usb-uhci
resources: ioport:f300-f31f irq:11
*-bridge
description: Bridge
product: 82371AB/EB/MB PIIX4 ACPI
vendor: Intel Corp.
physical id: 7.3
bus info: [EMAIL PROTECTED]:07.3
version: 01
width: 32 bits
clock: 33MHz
capabilities: bridge
configuration: driver=piix4 smbus
resources: irq:9
*-scsi
description: SCSI storage controller
physical id: 3
logical name: scsi0
capabilities: scsi-host
configuration: driver=aha152x
*-disk:0
description: SCSI Disk
product: DNES-309170
vendor: IBM
physical id: 0.0.0
bus info: [EMAIL PROTECTED]:0.0
logical name: /dev/sda
version: SA30
size: 8748MB
capacity: 8964MB
capabilities: 7200rpm
configuration: ansiversion=3
*-disk:1
description: SCSI Disk
product: DNES-309170
vendor: IBM
physical id: 0.1.0
bus info: [EMAIL PROTECTED]:1.0
logical name: /dev/sdb
version: SA30
size: 8748MB
capacity: 8964MB
capabilities: 7200rpm
configuration: ansiversion=3
*-cdrom:0
description: SCSI CD-ROM
product: CD-ROM PX-40TS
vendor: PLEXTOR
physical id: 0.2.0
bus info: [EMAIL PROTECTED]:2.0
logical name: /dev/scd0
logical name: /dev/sr0
version: 1.10
capabilities: removable audio
configuration: ansiversion=2
*-cdrom:1
description: CD-R/CD-RW writer
product: CRW8424S
vendor: YAMAHA
physical id: 0.3.0
bus info: [EMAIL PROTECTED]:3.0
logical name: /dev/scd1
logical name: /dev/sr1
version: 1.0d
capabilities: removable audio cd-r cd-rw
configuration: ansiversion=2
*-usb UNCLAIMED
description: Generic USB device
product: CanoScan
vendor: Canon
physical id: 4
bus info: [EMAIL PROTECTED]:3
version: 1.00
capabilities: usb-1.00
configuration: maxpower=500mA speed=12.0MB/s
*-network
description: Ethernet interface
physical id: 1
logical name: eth0
serial: 00:00:86:52:4b:cb
capabilities: ethernet physical
configuration: broadcast=yes driver=3c589_cs driverversion=1.162
ip=192.168.0.2 multicast=yes
ask more if you need,
--
/ \
((__-^^-,-^^-__))
.''`. Philippe BOURCIER `-_---' `---_-' .-.
: :' : http://bourcier.philippe.online.fr `--|o` 'o|--' /V\
`. `' \ ` / // \\
`- Linux Counter registered user #290012 ): :( /( )\
:o_o: ^^-^^
"-"
----- End forwarded message -----
--
maks
kernel janitor http://janitor.kernelnewbies.org/
personal weblog http://www.sternwelten.at/weblog.shtml
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
