I am sorry to report that the package above did not work. I can see my
AP by "iwlist scan" but it does not associate.
I have attached some results of the test. Switching back to 20060928
made the system working again with the same configuration files (old
bugs are back again, too).
Regards,
Ulf
wmaster0 IEEE 802.11g Frequency:2.427 GHz
RTS thr:off Fragment thr=2346 B
wlan0 IEEE 802.11g ESSID:"Schoger-Online"
Mode:Managed Frequency:2.427 GHz Access Point: 00:13:49:7F:94:85
RTS thr:off Fragment thr=2346 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
00:40:13.235974 wlan0 Scan request completed
00:40:13.236456 wlan0 Set Frequency:2.427 GHz
00:40:13.236591 wlan0 Set ESSID:"Schoger-Online"
00:40:19.039686 wlan0 Scan request completed
00:40:19.039844 wlan0 Set Frequency:2.427 GHz
00:40:19.039938 wlan0 Set ESSID:"Schoger-Online"
00:40:24.844034 wlan0 Scan request completed
00:40:24.844197 wlan0 Set Frequency:2.427 GHz
00:40:24.844291 wlan0 Set ESSID:"Schoger-Online"
wlan0 Scan completed :
Cell 01 - Address: 00:13:49:7F:94:85
ESSID:"Schoger-Online"
Mode:Master
Frequency:2.427 GHz
Encryption key:on
Extra:wpa_ie=dd160050f20101000050f20201000050f20201000050f202
Extra:tsf=000000593546325b
Linux version 2.6.18-3-686 (Debian 2.6.18-7) ([EMAIL PROTECTED]) (gcc version
4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #1 SMP Mon Dec 4 16:41:14 UTC
2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126960 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 Acer ) @ 0x000fe030
ACPI: RSDT (v001 Acer FALCON25 0x00000001 Acer 0x00000000) @ 0x1fff0000
ACPI: FADT (v001 Acer FALCON25 0x00000001 Acer 0x00000000) @ 0x1fff0054
ACPI: BOOT (v001 Acer FALCON25 0x00000001 Acer 0x00000000) @ 0x1fff002c
ACPI: DSDT (v001 Acer FALCON25 0x00000001 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0xf108
Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
Detected 596.896 MHz processor.
Built 1 zonelists. Total pages: 131056
Kernel command line: root=/dev/hda5 ro irqpoll
Misrouted IRQ fixup and polling support enabled
This may significantly impact system performance
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0140a000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512056k/524224k available (1543k kernel code, 11584k reserved, 574k
data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1203.66 BogoMIPS (lpj=2407323)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0c00)
CPU0: Intel Pentium III (Coppermine) stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4409k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [PILA] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILB] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILC] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILD] (IRQs 1 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILE] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [PILF] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [PILG] (IRQs 1 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILH] (IRQs 1 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILI] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI: Firmware left 0000:00:0a.0 e100 interrupts enabled, disabling
PCI quirk: region f100-f13f claimed by ali7101 ACPI
PCI quirk: region f140-f15f claimed by ali7101 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 34) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0b: ioport range 0xf100-0xf13f could not be reserved
pnp: 00:0b: ioport range 0xf140-0xf15f has been reserved
pnp: 00:0b: ioport range 0x1060-0x106f has been reserved
pnp: 00:0b: ioport range 0x40b-0x40b has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 8000-8fff
MEM window: 80600000-820fffff
PREFETCH window: disabled.
PCI: Bus 2, cardbus bridge: 0000:00:13.0
IO window: 00001400-000014ff
IO window: 00001800-000018ff
PREFETCH window: 30000000-31ffffff
MEM window: 32000000-33ffffff
PCI: Bus 6, cardbus bridge: 0000:00:13.1
IO window: 00001c00-00001cff
IO window: 00002000-000020ff
PREFETCH window: 34000000-35ffffff
MEM window: 36000000-37ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [PILB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [PILB] -> GSI 11 (level, low) ->
IRQ 11
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [PILB] -> GSI 11 (level, low) ->
IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag at 0x6e set to 0x1
audit: initializing netlink socket (disabled)
audit(1169767915.136:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THR2] (55 C)
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [PILD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [PILD] -> GSI 10 (level, low) ->
IRQ 10
e100: eth0: e100_probe: addr 0x80100000, irq 10, MAC addr 00:00:E2:34:5E:6B
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ACPI: Unable to derive IRQ for device 0000:00:10.0
ACPI: PCI Interrupt 0000:00:10.0[A]: no GSI - using IRQ 15
PCI: setting IRQ 15 as level-triggered
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x6050-0x6057, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x6058-0x605f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
hda: IBM-DJSA-210, ATA DISK drive
Time: acpi_pm clocksource has been installed.
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITADVD-ROM SR-8175, ATAPI CD/DVD-ROM drive
irq 15: nobody cared (try booting with the "irqpoll" option)
[<c014037f>] __report_bad_irq+0x2b/0x69
[<c014056c>] note_interrupt+0x1af/0x1e7
[<c013fc5c>] __do_IRQ+0xb3/0xe8
[<c01050e5>] do_IRQ+0x43/0x52
[<c01036b6>] common_interrupt+0x1a/0x20
[<c0121863>] __do_softirq+0x51/0xbb
[<c0121903>] do_softirq+0x36/0x3a
[<c01050ea>] do_IRQ+0x48/0x52
[<c01036b6>] common_interrupt+0x1a/0x20
[<c02810a0>] _spin_unlock_irqrestore+0x8/0x9
[<c01401dc>] setup_irq+0x12b/0x184
[<e0868928>] ide_intr+0x0/0x190 [ide_core]
[<c01402b1>] request_irq+0x7c/0x98
[<e086bb59>] init_irq+0x200/0x449 [ide_core]
[<c01b0d22>] register_blkdev+0xc8/0xd2
[<c0210844>] __driver_attach+0x0/0x5d
[<e086bec3>] hwif_init+0x121/0x2c4 [ide_core]
[<c0210844>] __driver_attach+0x0/0x5d
[<e086c176>] probe_hwif_init_with_fixup+0x1a/0x63 [ide_core]
[<e086df4f>] ide_setup_pci_device+0x62/0x6d [ide_core]
[<c01c1578>] pci_device_probe+0x36/0x57
[<c02107a5>] driver_probe_device+0x42/0x8b
[<c021087c>] __driver_attach+0x38/0x5d
[<c02102c6>] bus_for_each_dev+0x33/0x55
[<c021070f>] driver_attach+0x11/0x13
[<c0210844>] __driver_attach+0x0/0x5d
[<c020ffdf>] bus_add_driver+0x64/0xfd
[<c01c16b4>] __pci_register_driver+0x47/0x63
[<c01358f5>] sys_init_module+0x16c3/0x1846
[<c0161c50>] cp_new_stat64+0xfd/0x10f
[<c0102c7b>] syscall_call+0x7/0xb
handlers:
[<e0868928>] (ide_intr+0x0/0x190 [ide_core])
Disabling IRQ #15
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt Link [PILI] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [PILI] -> GSI 11 (level, low) ->
IRQ 11
ohci_hcd 0000:00:14.0: OHCI Host Controller
ohci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:14.0: irq 11, io mem 0x82400000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: max request size: 128KiB
hda: 11733120 sectors (6007 MB) w/384KiB Cache, CHS=12416/15/63, UDMA(33)
hda: cache flushes not supported
hda:<6>usb 1-2: new low speed USB device using ohci_hcd and address 2
hda1 hda2 < hda5 hda6 >
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:14.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Attempting manual resume
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
Linux agpgart interface v0.101 (c) Dave Jones
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Yenta: CardBus bridge found at 0000:00:13.0 [1025:1010]
Yenta O2: res at 0x94/0xD4: ea/00
Yenta O2: enabling read prefetch/write burst
input: PC Speaker as /class/input/input2
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000820
Yenta: CardBus bridge found at 0000:00:13.1 [1025:1010]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
agpgart: Detected ALi M???? chipset
agpgart: AGP aperture is 64M @ 0xe0000000
Real Time Clock Driver v1.12ac
pccard: CardBus card inserted into slot 0
Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input3
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
ACPI: PCI Interrupt Link [PILH] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [PILH] -> GSI 10 (level, low) ->
IRQ 10
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
irda_init()
NET: Registered protocol family 23
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337
0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337
0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Loading module: rt2500pci - CVS (20070104) by http://rt2x00.serialmonkey.com.
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [PILB] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:02:00.0 to 64
wmaster0: Selected rate control algorithm 'simple'
Adding 265032k swap on /dev/hda6. Priority:-1 extents:1 across:265032k
EXT3 FS on hda5, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED]
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect
breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
wlan0: starting scan
wlan0: scan completed
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: AC Adapter [AC] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6 over IPv4 tunneling driver
wlan0: scan completed
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
wlan0: starting scan
wlan0: scan completed
wlan0: no IPv6 routers present
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:13:49:7f:94:85
wlan0: authenticate with AP 00:13:49:7f:94:85
wlan0: authenticate with AP 00:13:49:7f:94:85
wlan0: authentication with AP 00:13:49:7f:94:85 timed out
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
wlan0: scan completed
wlan0: starting scan
