Package: installation-reports Version: 2.23 Severity: important
-- Package-specific info: Boot method: network Image version: http://people.debian.org/~stappers/d-i/images/daily/sparc64/netboot/2.6/boot.img build 27/Nov/2006 Date: <Date and time of the install> Machine: Sun Netra X1 Partitions: <df -Tl will do; the raw partition table is preferred> pingu:~# fdisk -l /dev/hda Disk /dev/hda (Sun disk label): 16 heads, 63 sectors, 39691 cylinders Units = cylinders of 1008 * 512 bytes Device Flag Start End Blocks Id System /dev/hda1 0 992 499968 1 Boot ~/dev/hda2 992 20368 9765504 83 Linux native /dev/hda3 0 39693 20005272 5 Whole disk /dev/hda4 20368 22306 976752 82 Linux swap /dev/hda5 22306 24290 999936 1 Boot /dev/hda6 24290 26274 999936 83 Linux native /dev/hda7 26274 32983 3381336 83 Linux native /dev/hda8 32983 39693 3381840 83 Linux native Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot: [O] Detect network card: [E] Configure network: [O] Detect CD: [ ] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Install base system: [O] Clock/timezone setup: [O] User/password setup: [O] Install tasks: [O] Install boot loader: [O] Overall install: [O] Comments/Problems: The install went well apart from the loading of the wrong driver for the onboard network devices DM9102 devices. The installer said that it was loading the Tulip driver but also loaded the dmfe driver prior to it. The dmfe driver "ate" the devices and Tulip found nothing to probe. This is a problem because dmfe does not work with the onboard devices - it gives lots of PCI bus errors and does not actually transfer traffic. I was able to drop down to a shell and unload both dmfe and tulip with modprobe -r and then reload tulip only. At this stage the networks setup just fine. Note the same problem arose during the reboot after installation. FYI this machine/model is not capable of booting from a CD drive so it is vital that network devices get loaded properly during install. Here are a few bits of relevant output from the system. Devices being loaded... TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) eth0: Davicom DM9102 at pci0000:00:05.0, 00:00:00:00:00:00, irq 7418560. eth1: Davicom DM9102 at pci0000:00:0c.0, 00:00:00:00:00:00, irq 7417856. Linux Tulip driver version 1.1.13-NAPI (May 11, 2002) ohci_hcd 0000:00:0a.0: OHCI Host Controller We get a similar thing in the output during the post install boot ALI15X3: 100% native mode on irq 5,7cc ide0: BM-DMA at 0x1fe02010220-0x1fe02010227, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1fe02010228-0x1fe0201022f, BIOS settings: hdc:pio, hdd:piodmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) hda: ST320423A, ATA DISK drive ide0 at 0x1fe02010200-0x1fe02010207,0x1fe0201020a on irq 5,7cc hdc: ST320423A, ATA DISK drive ide1 at 0x1fe02010210-0x1fe02010217,0x1fe0201020e on irq 5,7cc eth0: Davicom DM9102 at pci0000:00:05.0, 00:00:00:00:00:00, irq 7418560. eth1: Davicom DM9102 at pci0000:00:0c.0, 00:00:00:00:00:00, irq 7417856. Linux Tulip driver version 1.1.13-NAPI (May 11, 2002) hda: max request size: 128KiB -- Please make sure that the hardware-summary log file, and any other installation logs that you think would be useful are attached to this report. Once you have filled out this report, mail it to [EMAIL PROTECTED] ============================================== Installer lsb-release: ============================================== DISTRIB_ID=Debian DISTRIB_DESCRIPTION="Debian GNU/Linux installer" DISTRIB_RELEASE="4.0 (installer build 20061127-12:05)" X_INSTALLATION_MEDIUM=netboot-2.6 ============================================== Installer hardware-summary: ============================================== umame -a: Linux pingu 2.6.17-2-sparc64 #1 Wed Sep 13 10:39:24 PDT 2006 sparc64 unknown lspci -nn: 00:00.0 Host bridge [0600]: Sun Microsystems Computer Corp. Ultra IIe [108e:a001] lspci -nn: 00:03.0 Non-VGA unclassified device [0000]: ALi Corporation M7101 Power Management Controller [PMU] [10b9:7101] lspci -nn: 00:05.0 Ethernet controller [0200]: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31) lspci -nn: 00:07.0 ISA bridge [0601]: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] [10b9:1533] lspci -nn: 00:0a.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) lspci -nn: 00:0c.0 Ethernet controller [0200]: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31) lspci -nn: 00:0d.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229] (rev c3) lspci -vnn: 00:00.0 Host bridge [0600]: Sun Microsystems Computer Corp. Ultra IIe [108e:a001] lspci -vnn: Flags: bus master, 66MHz, medium devsel, latency 40 lspci -vnn: lspci -vnn: 00:03.0 Non-VGA unclassified device [0000]: ALi Corporation M7101 Power Management Controller [PMU] [10b9:7101] lspci -vnn: Flags: medium devsel lspci -vnn: lspci -vnn: 00:05.0 Ethernet controller [0200]: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31) lspci -vnn: Flags: bus master, medium devsel, latency 160, IRQ 7418560 lspci -vnn: I/O ports at 1fe02010100 [size=256] lspci -vnn: Memory at 1ff00002000 (32-bit, non-prefetchable) [size=256] lspci -vnn: Expansion ROM at 1ff00100000 [disabled] [size=256K] lspci -vnn: Capabilities: [50] Power Management version 1 lspci -vnn: lspci -vnn: 00:07.0 ISA bridge [0601]: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] [10b9:1533] lspci -vnn: Subsystem: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] [10b9:1533] lspci -vnn: Flags: bus master, medium devsel, latency 0 lspci -vnn: Capabilities: [a0] Power Management version 1 lspci -vnn: lspci -vnn: 00:0a.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10) lspci -vnn: Flags: bus master, medium devsel, latency 32, IRQ 7418816 lspci -vnn: Memory at 1ff01000000 (32-bit, non-prefetchable) [size=4K] lspci -vnn: Capabilities: [60] Power Management version 2 lspci -vnn: lspci -vnn: 00:0c.0 Ethernet controller [0200]: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31) lspci -vnn: Flags: bus master, medium devsel, latency 160, IRQ 7417856 lspci -vnn: I/O ports at 1fe02010000 [size=256] lspci -vnn: [virtual] Memory at 1ff00000000 (32-bit, non-prefetchable) [size=256] lspci -vnn: Expansion ROM at 1ff00040000 [disabled] [size=256K] lspci -vnn: Capabilities: [50] Power Management version 1 lspci -vnn: lspci -vnn: 00:0d.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229] (rev c3) (prog-if ff) lspci -vnn: Flags: bus master, medium devsel, latency 16, IRQ 7418048 lspci -vnn: I/O ports at 1fe02010200 [size=8] lspci -vnn: I/O ports at 1fe02010208 [size=4] lspci -vnn: I/O ports at 1fe02010210 [size=8] lspci -vnn: I/O ports at 1fe0201020c [size=4] lspci -vnn: I/O ports at 1fe02010220 [size=16] lspci -vnn: Capabilities: [60] Power Management version 2 lspci -vnn: lsmod: Module Size Used by lsmod: xfs 483216 0 lsmod: reiserfs 312448 0 lsmod: jfs 195440 0 lsmod: ext3 151248 3 lsmod: jbd 58344 1 ext3 lsmod: vfat 14464 0 lsmod: fat 56304 1 vfat lsmod: isofs 44464 0 lsmod: ide_cd 45128 0 lsmod: cdrom 41064 1 ide_cd lsmod: ide_generic 1664 0 [permanent] lsmod: cmd64x 12152 0 [permanent] lsmod: cs5520 5632 0 [permanent] lsmod: cs5530 6080 0 [permanent] lsmod: cy82c693 5384 0 [permanent] lsmod: it821x 9540 0 [permanent] lsmod: ns87415 5100 0 [permanent] lsmod: pdc202xx_new 9984 0 [permanent] lsmod: pdc202xx_old 11648 0 [permanent] lsmod: serverworks 10512 0 [permanent] lsmod: siimage 12864 0 [permanent] lsmod: trm290 5250 0 [permanent] lsmod: via82cxxx 10372 0 [permanent] lsmod: ide_disk 17536 5 lsmod: generic 5892 0 [permanent] lsmod: alim15x3 13336 0 [permanent] lsmod: tulip 53832 0 lsmod: ohci_hcd 19588 0 df: Filesystem 1k-blocks Used Available Use% Mounted on df: tmpfs 257376 912 256464 0% /dev df: tmpfs 257376 912 256464 0% /dev df: tmpfs 257376 912 256464 0% /.dev df: /dev/ide/host0/bus0/target0/lun0/part7 3328136 603544 2555528 19% /target df: /dev/ide/host0/bus0/target0/lun0/part5 984184 24520 909668 3% /target/boot df: /dev/ide/host0/bus0/target0/lun0/part8 3328640 1928424 1231124 61% /target/home free: total used free shared buffers free: Mem: 514752 423464 91288 0 27928 free: Swap: 976736 912 975824 free: Total: 1491488 424376 1067112 cardctl status: /usr/bin/report-hw: /usr/bin/report-hw: 28: pccardctl: not found cardctl ident: /usr/bin/report-hw: /usr/bin/report-hw: 29: pccardctl: not found cardctl status: /usr/bin/report-hw: /usr/bin/report-hw: 30: cardctl: not found cardctl ident: /usr/bin/report-hw: /usr/bin/report-hw: 31: cardctl: not found /proc/cpuinfo: cpu : TI UltraSparc IIe (Hummingbird) /proc/cpuinfo: fpu : UltraSparc IIe integrated FPU /proc/cpuinfo: prom : OBP 4.0.9 2001/05/17 21:52 /proc/cpuinfo: type : sun4u /proc/cpuinfo: ncpus probed : 1 /proc/cpuinfo: ncpus active : 1 /proc/cpuinfo: D$ parity tl1 : 0 /proc/cpuinfo: I$ parity tl1 : 0 /proc/cpuinfo: Cpu0Bogo : 11.12 /proc/cpuinfo: Cpu0ClkTck : 0000000017d78400 /proc/cpuinfo: MMU Type : Spitfire /proc/ioports: 1fe02000000-1fe02ffffff : SABRE0 PBMA /proc/ioports: 1fe02000070-1fe02000071 : rtc /proc/ioports: 1fe020002e8-1fe020002ef : serial /proc/ioports: 1fe020003f8-1fe020003ff : serial /proc/ioports: 1fe02002000-1fe0200203f : 0000:00:03.0 /proc/ioports: 1fe02004000-1fe0200401f : 0000:00:03.0 /proc/ioports: 1fe02008010-1fe02008011 : SUNW,lomh /proc/ioports: 1fe02010000-1fe020100ff : 0000:00:0c.0 /proc/ioports: 1fe02010000-1fe020100ff : tulip /proc/ioports: 1fe02010100-1fe020101ff : 0000:00:05.0 /proc/ioports: 1fe02010100-1fe020101ff : tulip /proc/ioports: 1fe02010200-1fe02010207 : 0000:00:0d.0 /proc/ioports: 1fe02010200-1fe02010207 : ide0 /proc/ioports: 1fe02010208-1fe0201020b : 0000:00:0d.0 /proc/ioports: 1fe0201020a-1fe0201020a : ide0 /proc/ioports: 1fe0201020c-1fe0201020f : 0000:00:0d.0 /proc/ioports: 1fe0201020e-1fe0201020e : ide1 /proc/ioports: 1fe02010210-1fe02010217 : 0000:00:0d.0 /proc/ioports: 1fe02010210-1fe02010217 : ide1 /proc/ioports: 1fe02010220-1fe0201022f : 0000:00:0d.0 /proc/ioports: 1fe02010220-1fe02010227 : ide0 /proc/ioports: 1fe02010228-1fe0201022f : ide1 /proc/iomem: 1ff00000000-1ff5fffffff : SABRE0 PBMA /proc/iomem: 1ff00000000-1ff000000ff : 0000:00:0c.0 /proc/iomem: 1ff00000000-1ff000000ff : tulip /proc/iomem: 1ff00002000-1ff000020ff : 0000:00:05.0 /proc/iomem: 1ff00002000-1ff000020ff : tulip /proc/iomem: 1ff00040000-1ff0007ffff : 0000:00:0c.0 /proc/iomem: 1ff000a0000-1ff000bffff : Video RAM area /proc/iomem: 1ff000c0000-1ff000c7fff : Video ROM /proc/iomem: 1ff000f0000-1ff000fffff : System ROM /proc/iomem: 1ff00100000-1ff0013ffff : 0000:00:05.0 /proc/iomem: 1ff01000000-1ff01000fff : 0000:00:0a.0 /proc/iomem: 1ff01000000-1ff01000fff : ohci_hcd /proc/interrupts: 0: 1938325 timer:dead /proc/interrupts: 5: 41140 ide0:7cc, ide1:7cc /proc/interrupts: 6: 206915 eth1:7c6 /proc/interrupts: 12: 33538 su(serial):7eb /proc/interrupts: 14: 0 ohci_hcd:usb1:7e4 /proc/interrupts: 15: 2 SABRE UE:7ee, SABRE CE:7ef, SABRE PCIERR:7f0, power:7e5 /proc/meminfo: MemTotal: 514752 kB /proc/meminfo: MemFree: 91272 kB /proc/meminfo: Buffers: 27928 kB /proc/meminfo: Cached: 329120 kB /proc/meminfo: SwapCached: 296 kB /proc/meminfo: Active: 206064 kB /proc/meminfo: Inactive: 166456 kB /proc/meminfo: HighTotal: 0 kB /proc/meminfo: HighFree: 0 kB /proc/meminfo: LowTotal: 514752 kB /proc/meminfo: LowFree: 91272 kB /proc/meminfo: SwapTotal: 976736 kB /proc/meminfo: SwapFree: 975824 kB /proc/meminfo: Dirty: 584 kB /proc/meminfo: Writeback: 0 kB /proc/meminfo: Mapped: 17128 kB /proc/meminfo: Slab: 45336 kB /proc/meminfo: CommitLimit: 1234112 kB /proc/meminfo: Committed_AS: 20800 kB /proc/meminfo: PageTables: 432 kB /proc/meminfo: VmallocTotal: 4194304 kB /proc/meminfo: VmallocUsed: 1800 kB /proc/meminfo: VmallocChunk: 4192504 kB dmidecode: /usr/bin/report-hw: /usr/bin/report-hw: 39: dmidecode: not found ============================================== Installer status: ============================================== Package: preseed-common Status: install ok unpacked Version: 1.21 Depends: cdebconf-udeb, di-utils (>= 1.14) Description: common files for preseeding Package: udpkg Status: install ok unpacked Version: 1.04 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.41) Description: tiny dpkg clone Package: localechooser Status: install ok installed Version: 1.30 Depends: cdebconf-udeb, iso-3166-udeb, di-utils (>= 1.15) Description: choose language/country/locale Installer-Menu-Item: 10 Package: libnss-dns-udeb Status: install ok unpacked Version: 2.3.6.ds1-8 Description: GNU C Library: NSS helper for DNS - udeb Package: download-installer Status: install ok installed Version: 1.12 Depends: cdebconf-udeb, net-retriever, anna (>= 1.07) Description: Download installer components Installer-Menu-Item: 23 Package: lowmemcheck Status: install ok unpacked Version: 1.22 Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03) Description: detect low-memory systems and enter lowmem mode Package: main-menu Status: install ok unpacked Version: 1.15 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.45), cdebconf-udeb Description: Debian installer main menu Package: di-utils-shell Status: install ok installed Version: 1.41 Depends: cdebconf-udeb, di-utils (>= 1.18) Description: Execute a shell Installer-Menu-Item: 950 Package: di-utils Status: install ok installed Version: 1.41 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.47), cdebconf-udeb Description: Miscellaneous utilities for the debian installer Package: choose-mirror Status: install ok installed Version: 2.08 Depends: configured-network, choose-mirror-bin Description: Choose mirror to install from (menu item) Installer-Menu-Item: 23 Package: network-preseed Status: install ok unpacked Version: 1.21 Depends: cdebconf-udeb, configured-network, preseed-common Description: download debconf preseed file Installer-Menu-Item: 21 Package: cdebconf-newt-udeb Status: install ok unpacked Version: 0.109 Depends: cdebconf-udeb, di-utils-terminfo, libc6 (>= 2.3.5-1), libnewt0.52 Description: Newt frontend for Debian Configuration Management System Package: module-init-tools-udeb Status: install ok unpacked Version: 3.3-pre3-1 Depends: libc6 (>= 2.3.5-1) Description: tools for managing Linux kernel modules Package: rootskel Status: install ok installed Version: 1.45 Depends: di-utils (>= 1.24), cdebconf-udeb Description: Skeleton root filesystem used by debian-installer Package: udev-udeb Status: install ok unpacked Version: 0.103-1 Depends: libc6 (>= 2.3.5-1) Description: /dev/ and hotplug management daemon Package: libfribidi0-udeb Status: install ok unpacked Version: 0.10.7-4 Depends: libc6 (>= 2.3.5-1) Description: Free Implementation of the Unicode BiDi algorithm Package: nic-modules-2.6.17-2-sparc64-di Status: install ok unpacked Version: 1.14 Provides: nic-modules Depends: kernel-image-2.6.17-2-sparc64-di Description: Network card modules for Sparc kernels Package: libtextwrap1-udeb Status: install ok installed Version: 0.1-5 Depends: libc6 (>= 2.3.5-1) Description: text-wrapping library with i18n - runtime udeb Package: auto-install Status: install ok unpacked Version: 0.02 Depends: netcfg, preseed-common (>= 1.18) Description: Support for automatic installs Installer-Menu-Item: 19 Package: usb-discover Status: install ok unpacked Version: 1.06 Depends: cdebconf-udeb Description: Discover USB and load kernel modules Package: rescue-check Status: install ok unpacked Version: 1.7 Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03), di-utils (>= 1.18) Description: enter d-i rescue mode if requested Package: nano-udeb Status: install ok unpacked Version: 2.0.1-1 Provides: editor Depends: libc6 (>= 2.3.5-1), libslang2-udeb (>= 2.0.6-3) Description: free Pico clone with some new features - tiny build Package: cdebconf-udeb Status: install ok installed Version: 0.109 Provides: debconf-2.0 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.45), libtextwrap1-udeb Description: Debian Configuration Management System (C-implementation) Package: ai-choosers Status: install ok unpacked Version: 0.02 Depends: kbd-chooser (>= 1.30), localechooser (>= 1.23) Description: Delayed configuration of locale and keyboard for auto-install Installer-Menu-Item: 22 Package: libiw28-udeb Status: install ok installed Version: 28-1 Depends: libc6 (>= 2.3.5-1) Description: Tools for manipulating Linux Wireless Extensions Package: cdebconf-text-udeb Status: install ok unpacked Version: 0.109 Depends: cdebconf-udeb, libc6 (>= 2.3.5-1) Description: Plain text frontend for Debian Configuration Management System Package: iso-3166-udeb Status: install ok installed Version: 0.58-1 Description: provides iso_3166.tab file Package: ethdetect Status: install ok installed Version: 1.43 Provides: ethernet-card-detection Depends: rootskel (>= 1.30), cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13) Description: Detect network hardware and load kernel drivers for it Installer-Menu-Item: 18 Package: busybox-udeb Status: install ok unpacked Version: 1:1.1.3-3 Depends: libc6 (>= 2.3.5-1) Description: Tiny utilities for the debian-installer Package: initrd-preseed Status: install ok unpacked Version: 1.21 Depends: preseed-common Description: load debconf preseed file from /preseed.cfg on the initrd Package: net-retriever Status: install ok installed Version: 1.12 Provides: retriever Depends: cdebconf-udeb, choose-mirror, configured-network, di-utils (>= 1.16) Description: Fetch modules from the Internet Package: usb-modules-2.6.17-2-sparc64-di Status: install ok unpacked Version: 1.14 Provides: usb-modules Depends: kernel-image-2.6.17-2-sparc64-di Description: USB support Package: archdetect Status: install ok installed Version: 1.43 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.45) Description: Hardware architecture detector Package: save-logs Status: install ok unpacked Version: 2.23 Depends: cdebconf-udeb Description: save logs and configuration for debug purposes Installer-Menu-Item: 940 Package: di-utils-reboot Status: install ok unpacked Version: 1.41 Depends: cdebconf-udeb Description: Reboot Installer-Menu-Item: 995 Package: anna Status: install ok installed Version: 1.25 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.45), cdebconf-udeb Description: anna's not nearly apt, but for the Debian installer, it will do Package: choose-mirror-bin Status: install ok installed Version: 2.08 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.45), cdebconf-udeb Description: Choose mirror to install from (program) Package: pciutils-udeb Status: install ok unpacked Version: 1:2.2.4-1 Depends: libc6 (>= 2.3.5-1), zlib1g-udeb (>= 1:1.2.1) Description: Linux PCI Utilities (udeb) Package: console-keymaps-at Status: install ok installed Version: 2:1.01-2 Provides: console-keymaps Depends: cdebconf-udeb Description: Keymaps for PC-style (PS/2 and AT) keyboards Package: di-utils-terminfo Status: install ok unpacked Version: 1.41 Description: Terminfo entries needed by newt/slang in debian installer Package: sparc-utils-udeb Status: install ok unpacked Version: 1.9-3 Depends: libc6 (>= 2.3.5-1) Description: sparc-utils package for the Debian installer Package: hw-detect Status: install ok installed Version: 1.43 Depends: rootskel (>= 1.30), archdetect, cdebconf-udeb (>= 0.75), di-utils (>= 1.26) Description: Detect hardware and load kernel drivers for it Package: kbd-chooser Status: install ok installed Version: 1.31 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.45), cdebconf-udeb, console-keymaps Description: Detect a keyboard and select layout Installer-Menu-Item: 12 Package: libdebian-installer4-udeb Status: install ok installed Version: 0.47 Depends: libc6 (>= 2.3.5-1) Description: Library of common debian-installer functions Package: kernel-image-2.6.17-2-sparc64-di Status: install ok unpacked Version: 1.14 Provides: kernel-image, ext2-modules Description: Linux kernel binary image for the Debian installer Package: installation-locale Status: install ok unpacked Version: 1.1 Depends: rootskel Description: UTF-8 C locale Package: env-preseed Status: install ok unpacked Version: 1.21 Description: debconf preseeding via environment variables Package: cdebconf-priority Status: install ok unpacked Version: 0.109 Depends: cdebconf-udeb Description: Change debconf priority Installer-Menu-Item: 930 Package: netcfg Status: install ok installed Version: 1.31 Provides: configured-network Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.45), libiw28-udeb (>= 28), dhcp-client-udeb | dhcp3-client-udeb | pump-udeb, ethernet-card-detection Description: Configure the network Installer-Menu-Item: 18 Package: zlib1g-udeb Status: install ok unpacked Version: 1:1.2.3-13 Provides: zlib1g Description: compression library - runtime for Debian installer Package: dhcp-client-udeb Status: install ok installed Version: 2.0pl5-19.4 Depends: libc6 (>= 2.3.5-1) Description: DHCP Client for debian-installer Package: libdebconfclient0-udeb Status: install ok installed Version: 0.109 Depends: libc6 (>= 2.3.5-1), cdebconf-udeb Description: Debian Configuration Management System (C-implementation) Package: bogl-bterm-udeb Status: install ok unpacked Version: 0.1.18-1.5 Provides: editor Depends: libc-udeb Description: Ben's Own Graphics Library - graphical terminal Package: debian-installer Status: install ok installed Version: sparc64-netboot-2.6-20061127-12:05 Description: debian installation image Package: apt-mirror-setup Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 152 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1:0.16 Depends: choose-mirror-bin, cdebconf-udeb Description: set up a mirror in sources.list Package: apt-setup-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 100 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1:0.16 Depends: apt-mirror-setup, base-installer (>= 1.49), cdebconf-udeb Description: Configure apt Installer-Menu-Item: 70 Package: base-installer Status: install ok installed Priority: required Section: debian-installer Installed-Size: 612 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.69 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.45), mounted-partitions, debootstrap-udeb (>= 0.3.1), created-fstab, archdetect, di-utils-mapdevfs, di-utils (>= 1.16), rootskel (>= 1.19) Provides: kernel-installer Description: Install the base system Installer-Menu-Item: 65 Package: cdrom-core-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 216 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di, scsi-core-modules-2.6.17-2-sparc64-di, ide-modules-2.6.17-2-sparc64-di Provides: cdrom-core-modules Description: CDROM support This package contains core CDROM support for the Linux kernel. Package: clock-setup Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 72 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 0.12 Depends: cdebconf-udeb, os-prober, tzsetup-udeb Description: set up clock Installer-Menu-Item: 62 Package: debootstrap-udeb Status: install ok installed Priority: required Section: debian-installer Installed-Size: 160 Maintainer: Anthony Towns <[EMAIL PROTECTED]> Version: 0.3.3.1 Depends: libc6 (>= 2.3.5-1), mounted-partitions Description: Bootstrap the Debian system debootstrap is used to create a Debian base system from scratch, without requiring the availability of dpkg or apt. It does this by downloading .deb files from a mirror site, and carefully unpacking them into a directory which can eventually be chrooted into. . debootstrap-udeb is a minimal package used by debian-installer. Package: dhcp3-client-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 608 Maintainer: Eloy A. Paris <[EMAIL PROTECTED]> Version: 3.0.4-10 Depends: libc6 (>= 2.3.5-1) Description: DHCP Client for debian-installer dhcp-client-udeb is a minimal dhcp package used by the debian-installer. Package: di-utils-mapdevfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 16 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.41 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.47) Description: mapdevfs utility for the debian installer Package: disk-detect Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 60 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.43 Depends: cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13) Provides: harddrive-detection Description: Detect disk drives Installer-Menu-Item: 35 Package: e2fsprogs-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 400 Maintainer: Theodore Y. Ts'o <[EMAIL PROTECTED]> Version: 1.39+1.40-WIP-2006.11.14+dfsg-1 Depends: libblkid1-udeb, libc6 (>= 2.3.5-1) Description: stripped-down versions of e2fsprogs, for debian-installer This package is an e2fsprogs package built for a reduced size, so that it can help to save space in debian-installer. . Don't attempt to install this package, it has no support for a couple of features you surely want. Anyway it should refuse to install. Package: ext3-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 380 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: ext3-modules Description: EXT3 filesystem support This package contains the EXT3 filesystem module for the Linux kernel. Package: fat-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 168 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: fat-modules Description: FAT filesystem support This package contains the FAT and VFAT filesystem modules for the Linux kernel. Package: finish-install Status: install ok unpacked Priority: required Section: debian-installer Installed-Size: 108 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 2.5 Depends: cdebconf-udeb, archdetect, base-installer, created-fstab, bootable-system Provides: prebaseconfig Description: Finish the installation and reboot Installer-Menu-Item: 78 Package: ide-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 344 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: ide-modules Description: IDE drivers This package contains IDE drivers for the Linux kernel. Package: jfs-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 312 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: jfs-modules Description: JFS filesystem support This package contains the JFS filesystem module for the Linux kernel. Package: jfsutils-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 1100 Maintainer: Stefan Hornburg (Racke) <[EMAIL PROTECTED]> Version: 1.1.11-1 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Description: A stripped-down version of jfsutils, for debian-installer This package is a jfsutils package built for reduced size, so that it can help to save space in debian-installer. . Don't attempt to install this package, it has no support for a couple of features you surely want. Anyway, it should fail to install. Package: libblkid1-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 44 Maintainer: Theodore Y. Ts'o <[EMAIL PROTECTED]> Version: 1.39+1.40-WIP-2006.11.14+dfsg-1 Depends: libc6 (>= 2.3.5-1) Provides: libblkid1 Description: block device id library The blkid library which allows system programs like fsck and mount to quickly and easily find block devices by filesystem UUID and LABEL. This allows system administrators to avoid specifiying filesystems by hard-coded device names, but via a logical naming system instead. . This is a minimal package for debian-installer. Package: libc6-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 2028 Maintainer: GNU Libc Maintainers <debian-glibc@lists.debian.org> Version: 2.3.6.ds1-8 Provides: libc6, libc-udeb, glibc-2.3.6.ds1-1, glibc-2.3.6-2 Description: GNU C Library: Shared libraries - udeb Contains the standard libraries that are used by nearly all programs on the system. This package includes shared versions of the standard C library and the standard math library, as well as many others. . This package contains a minimal set of libraries needed for the Debian installer. Do not install it on a normal system. Package: libdevmapper1.02-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 84 Maintainer: Debian LVM Team <[EMAIL PROTECTED]> Version: 2:1.02.08-1 Depends: libc6 (>= 2.3.5-1) Provides: libdevmapper1.02 Description: The Linux Kernel Device Mapper userspace library This is a udeb, or a microdeb, for the debian-installer. . The Linux Kernel Device Mapper is the LVM (Linux Logical Volume Management) Team's implementation of a minimalistic kernel-space driver that handles volume management, while keeping knowledge of the underlying device layout in user-space. This makes it useful for not only LVM, but EVMS, software raid, and other drivers that create "virtual" block devices. Package: libparted1.7-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 404 Maintainer: Parted Maintainer Team <[EMAIL PROTECTED]> Version: 1.7.1-3 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Provides: libparted1.7-1 Description: The GNU Parted disk partitioning shared library GNU Parted is a program that allows you to create, destroy, resize, move and copy hard disk partitions. This is useful for creating space for new operating systems, reorganising disk usage, and copying data to new hard disks. This package contains the Parted binary and manual page. . This package contains libparted, the required shared library used by Parted. This is a cut-down package with no normal documentation intended to be used in debian-installer. . Parted currently supports DOS, Mac, Sun, BSD, GPT, MIPS and PC98 disklabels/partition tables, as well as a 'loop' (raw disk) type which allows use on RAID/LVM. Filesystems which are currently fully supported are ext2, ext3, fat (FAT16 and FAT32), ReiserFS (with libreiserfs) and linux-swap. Parted can also detect and remove HFS (Mac OS), JFS, NTFS, UFS (Sun and HP), XFS and ASFS/AFFS/APFS (Amiga) filesystems, but cannot create, resize or check these filesystems yet. . Note that ReiserFS support is only enabled if you install the libreiserfs0.3-0 package. Since libreiserfs0.3-0 has been removed from sarge, ReiserFS support is not compiled in the default package. . The nature of this software means that any bugs could cause massive data loss. While there are no known bugs at the moment, they could exist, so please back up all important files before running it, and do so at your own risk. Package: libuuid1-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 24 Maintainer: Theodore Y. Ts'o <[EMAIL PROTECTED]> Version: 1.39+1.40-WIP-2006.11.14+dfsg-1 Depends: libc6 (>= 2.3.5-1) Provides: libuuid1 Description: universally unique id library libuuid generates and parses 128-bit universally unique id's (UUID's). See RFC 4122 for more information. . This is a minimal package for debian-installer. Package: lvm2-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 516 Maintainer: Debian LVM Team <[EMAIL PROTECTED]> Version: 2.02.06-3 Depends: libc6 (>= 2.3.5-1), libdevmapper1.02-udeb (>= 2:1.02.02-2) Description: The Linux Logical Volume Manager This is a udeb, or a microdeb, for the debian-installer. . This is LVM2, the rewrite of The Linux Logical Volume Manager. LVM supports enterprise level volume management of disk and disk subsystems by grouping arbitrary disks into volume groups. The total capacity of volume groups can be allocated to logical volumes, which are accessed as regular block devices. Package: md-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 504 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: md-modules Description: RAID and LVM support This package contains RAID and LVM modules for the Linux kernel. Package: mdadm-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 208 Maintainer: Debian mdadm maintainers <[EMAIL PROTECTED]> Version: 2.5.6-6 Depends: libc6 (>= 2.3.5-1) Description: tool to administer Linux MD arrays (software RAID) mdadm is a program that can be used to create, manage, and monitor MD arrays (e.g. software RAID, multipath devices). . mdadm-udeb is a minimal package used by the debian-installer. Package: mdcfg-utils Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 384 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.19 Depends: cdebconf-udeb, di-utils (>= 1.16), md-modules, mdadm-udeb (>= 2.5.2), partconf-find-partitions Description: Configure MD devices Use this module to configure the MD devices. Package: mkreiserfs-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 192 Maintainer: Ed Boraas <[EMAIL PROTECTED]> Version: 1:3.6.19-4 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Description: User-level tools for ReiserFS filesystems This installer module contains the utility to create ReiserFS filesystems. . Homepage: http://www.namesys.com/ Package: nobootloader Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 156 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.15 Depends: cdebconf-udeb, base-installer (>= 1.23), di-utils-mapdevfs Provides: bootable-system Description: Don't install any bootloader. This package will skip installing a boot-loader Installer-Menu-Item: 77 Package: os-prober-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 96 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: di-utils-mapdevfs, anna (>= 1.16) Provides: os-prober Description: utility to detect other OSes on a set of drives This package is to be used by boot loader installers to detect other OSes available on a system, in a generic format, which it can then adapt to its own configuration format. Package: partconf-find-partitions Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 32 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.19 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.45), libparted1.7-udeb (>= 1.7.1-1) Description: debian-installer utility for finding partitions Helper program for finding partitions and detecting their size and existing file system. Package: parted-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 68 Maintainer: Parted Maintainer Team <[EMAIL PROTECTED]> Version: 1.7.1-3 Depends: libc6 (>= 2.3.5-1), libparted1.7-udeb (>= 1.7.1-1) Provides: parted Description: The GNU Parted disk partition resizing program GNU Parted is a program that allows you to create, destroy, resize, move and copy hard disk partitions. This is useful for creating space for new operating systems, reorganising disk usage, and copying data to new hard disks. This package contains the Parted binary and manual page. . This package is similar to the "big" parted package, but has less cosmetical features resulting in smaller binary. Intended to be used in debian-installer. . . The nature of this software means that any bugs could cause massive data loss. While there are no known bugs at the moment, they could exist, so please back up all important files before running it, and do so at your own risk. Package: partman-auto Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 376 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 61 Depends: cdebconf-udeb, di-utils, partman-base, partman-basicfilesystems, partman-ext3 Description: Automatically partition storage devices (partman) Package: partman-auto-crypto Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 48 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 3 Depends: cdebconf-udeb, partman-auto (>= 55), partman-auto-lvm (>= 14), partman-crypto (>= 13), partman-base (>= 87) Description: Automatically partition storage devices using crypto and LVM Package: partman-auto-lvm Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 148 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 18 Depends: cdebconf-udeb, partman-base (>= 73), partman-auto (>= 59), partman-lvm (>= 36), di-utils (>= 1.15), lvm2-udeb Description: Automatically partition storage devices using LVM Package: partman-auto-raid Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 64 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 2 Depends: cdebconf-udeb, partman-base, partman-basicfilesystems, partman-ext3, partman-auto (>= 58), partman-md Description: Allow preseeded RAID installs Package: partman-base Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 860 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 98 Depends: libc6 (>= 2.3.5-1), libparted1.7-udeb (>= 1.7.1-1), cdebconf-udeb, partman-partitioning, partman-target, archdetect, harddrive-detection, di-utils-mapdevfs, di-utils (>= 1.15) Provides: made-filesystems, mounted-partitions, partitioned-harddrives, created-fstab Description: Partition the storage devices (partman) Installer-Menu-Item: 42 Package: partman-basicfilesystems Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 576 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 49 Depends: cdebconf-udeb, e2fsprogs-udeb, ext2-modules, fat-modules, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for ext2, linux-swap, fat16 and fat32 Package: partman-basicmethods Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 124 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 32 Depends: cdebconf-udeb Provides: partman-method Description: Basic partition usage methods for partman This package provides partman with two methods to use partitions. The first is to format the partition. The second is to keep and use the existing data in the partition as it is. Package: partman-crypto Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 860 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 17 Depends: partman-base (>= 87), libc6 (>= 2.3.5-1), cdebconf-udeb Description: Add to partman support for block device encryption Package: partman-ext3 Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 220 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 43 Depends: cdebconf-udeb, e2fsprogs-udeb, ext3-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for ext3 Package: partman-jfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 260 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 18 Depends: cdebconf-udeb, jfsutils-udeb, jfs-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add support for jfs to partman Package: partman-lvm Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 680 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 47 Depends: cdebconf-udeb, partman-base (>= 87), di-utils (>= 1.14), md-modules, lvm2-udeb, parted-udeb Description: Adds support for LVM to partman Package: partman-md Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 156 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 30 Depends: cdebconf-udeb, mdadm-udeb, mdcfg-utils, partman-base (>= 87) Description: Add to partman support for MD Package: partman-partitioning Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 364 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 44 Depends: cdebconf-udeb Description: Partitioning operations for partman This udeb provides partman with editing operations for creation of new partitions, deletion of partitions and initialisation of the partition table. Package: partman-reiserfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 228 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 32 Depends: cdebconf-udeb, mkreiserfs-udeb, reiserfs-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for reiserfs Package: partman-target Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 304 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 46 Depends: cdebconf-udeb, partman-basicfilesystems, partman-basicmethods, di-utils-mapdevfs Description: Provides partman with ability to prepare /target This udeb allows the user to choose how partitions should be used. Package: partman-xfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 216 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 30 Depends: cdebconf-udeb, xfsprogs-udeb, xfs-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for xfs Package: pkgsel Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 28 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 0.10 Depends: cdebconf-udeb, apt-setup-udeb, di-utils (>= 1.20) Description: Select and install packages Installer-Menu-Item: 70 Package: reiserfs-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 452 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: reiserfs-modules Description: Reiser filesystem support This package contains the Reiser filesystem module for the Linux kernel. Package: sata-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 496 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di, scsi-core-modules-2.6.17-2-sparc64-di Provides: sata-modules Description: SATA drivers This package contains SATA drivers for the Linux kernel. Package: scsi-common-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 1416 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di, scsi-core-modules-2.6.17-2-sparc64-di, cdrom-core-modules-2.6.17-2-sparc64-di Provides: scsi-common-modules Description: Very common SCSI drivers This package contains very common SCSI drivers for the Linux kernel. Package: scsi-core-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 364 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: scsi-core-modules Description: Core SCSI subsystem This package contains the core SCSI subsystem for the Linux kernel. Package: scsi-extra-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 1416 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: scsi-core-modules-2.6.17-2-sparc64-di Provides: scsi-extra-modules Description: Uncommon SCSI drivers This package contains uncommon SCSI drivers for the Linux kernel. This includes SCSI RAID drivers, and some of the less common SCSI controllers. Package: silo-installer Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 196 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.07 Depends: cdebconf-udeb, base-installer, di-utils-mapdevfs, archdetect Provides: bootable-system Description: install silo on a hard disk This udeb will install silo on the hard disk. Installer-Menu-Item: 73 Package: tzsetup-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 300 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1:0.13 Depends: cdebconf-udeb, localechooser Description: choose timezone Installer-Menu-Item: 62 Package: user-setup-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 336 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.7 Depends: cdebconf-udeb Description: Set up users and passwords Installer-Menu-Item: 63 Package: xfs-modules-2.6.17-2-sparc64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 728 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.14 Depends: kernel-image-2.6.17-2-sparc64-di Provides: xfs-modules Description: XFS filesystem support This package contains the XFS filesystem module for the Linux kernel. Package: xfsprogs-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 256 Maintainer: Nathan Scott <[EMAIL PROTECTED]> Version: 2.8.11-1 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Description: A stripped-down version of xfsprogs, for debian-installer This package is an xfsprogs package built for reduced size, so that it can help to save space in debian-installer. . Don't attempt to install this package, it has no support for a couple of features you surely want. Anyway, it should fail to install. -- System Information: Debian Release: 4.0 APT prefers testing APT policy: (500, 'testing') Architecture: sparc (sparc64) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.17-2-sparc64 Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8) installation-report depends on no packages. Versions of packages installation-report recommends: pn pciutils <none> (no description available) ii reportbug 3.31 reports bugs in the Debian distrib -- no debconf information -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
