Package: smartmontools
Version: 5.32-3
Severity: normal
Subject: smartmontools reads NOT raw values
-- Package-specific info:
Ouput of /usr/share/bug/smartmontools:
# CONFIG_IDE_TASK_IOCTL is not set
-- System Information:
Debian Release: 3.1
Architecture: i386 (i686)
Kernel: Linux 2.4.27ltspke9-nf2-v07c-utf8-sata-ehci-experimental
Locale: LANG=sk_SK.UTF-8, LC_CTYPE=sk_SK.UTF-8 (charmap=UTF-8) (ignored:
LC_ALL set to sk_SK.UTF-8)
Versions of packages smartmontools depends on:
ii libc6 2.3.2.ds1-22sarge3 GNU C Library: Shared
libraries an
-- no debconf information
In my syslog is always:
May 18 06:14:45 ltsp smartd[7749]: Device: /dev/hda, SMART Usage
Attribute: 194 Temperature_Celsius changed from 117 to 114
So I changed my smartd.conf to:
from:
DEVICESCAN
/dev/hda -a -o on -S on -s (S/../.././02|L/../../6/03)
to:
DEVICESCAN
/dev/hda -R 194 -a -o on -S on -s (S/../.././02|L/../../7/03
(all other lines are default=commented)
but nothing change in syslog - I've got the same message!
Yes, I did:
/etc/init.d/smartmontools stop; sleep 15
/etc/init.d/smartmontools start
As you can see below, HDD is about 47-50 Celsium degrees {smartlctl -a}
The obly problem is smartd is NOT reading correctly this value even in
case you order him to read the RAW value.
=====================
$ smartctl -i /dev/hda
I think you will find this info usefull:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: IC35L120AVV207-1
Serial Number: VNVD01G4C3KS7G
Firmware Version: V24OA63A
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Fri May 19 13:38:35 2006 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=====================
$ smartctl -a /dev/hda
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: IC35L120AVV207-1
Serial Number: VNVD01G4C3KS7G
Firmware Version: V24OA63A
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Fri May 19 13:38:48 2006 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an
interrupting command from host.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (2855) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 48) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 060 Pre-fail
Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail
Offline - 0
3 Spin_Up_Time 0x0007 113 113 024 Pre-fail
Always - 239 (Average 245)
4 Start_Stop_Count 0x0012 100 100 000 Old_age
Always - 184
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 121 121 020 Pre-fail
Offline - 38
9 Power_On_Hours 0x0012 098 098 000 Old_age
Always - 19052
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 183
192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always
- 414
193 Load_Cycle_Count 0x0012 100 100 050 Old_age Always
- 414
194 Temperature_Celsius 0x0002 114 114 000 Old_age Always
- 48 (Lifetime Min/Max 15/59)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 18411
-
# 2 Short offline Completed without error 00% 18382
-
Device does not support Selective Self Tests/Logging
Thanks for smartmontools.
Thanks for Debian (best ever) distro.
Thanks to all Debian package managers.
--
Jan Kunder
jan.kunderHATESPAMgmail.com
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
