On Fri, Jun 24, 2022 at 02:10:44PM -0700, Vagrant Cascadian wrote: > Package: installation-reports > Severity: normal > X-Debbugs-Cc: vagr...@debian.org > > Boot method: network > Image version: > https://d-i.debian.org/daily-images/arm64/20220624-02:19/netboot/netboot.tar.gz > Date: 2022-06-24 after breakfast but before lunch > > Machine: Solidrun Honeycomb LX2 > Partitions: > udev devtmpfs 32513604 0 32513604 0% /dev > tmpfs tmpfs 6514616 744 6513872 1% /run > /dev/sda3 ext4 9510080 1530260 7475144 17% / > tmpfs tmpfs 32573080 0 32573080 0% /dev/shm > tmpfs tmpfs 5120 0 5120 0% /run/lock > /dev/sda1 vfat 389904 3536 386368 1% /boot/efi > tmpfs tmpfs 6514616 0 6514616 0% /run/user/1000 > > > Base System Installation Checklist: > [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it > > Initial boot: [O] > Detect network card: [E] > Configure network: [O] > Detect media: [O] > Load installer modules: [O] > Clock/timezone setup: [O] > User/password setup: [O] > Detect hard drives: [O] > Partition hard drives: [O] > Install base system: [O] > Install tasks: [O] > Install boot loader: [E] > Overall install: [E] > > Comments/Problems: > > On-board ethernet is not detected in debian-installer or even once the > system is installed. Worked around with a USB-ethernet adapter. > > Boot loader would install successfully, but grub would not boot when I > had a system with rootfs on lvm on raid1 (with degraded 1-disk > array). I think this sort of configuration used to work, but it has > been ages since I've tested. Will check another install if it works > better with a not degraded array (e.g. raid1, two disks). Workaround > was to use a plain partition with ext4 for rootfs. > > FWIW, Same issues with bullseye's installer too, so at least it's > not... a regression? :) > > > live well, > vagrant > > -- Package-specific info: > > ============================================== > Installer lsb-release: > ============================================== > DISTRIB_ID=Debian > DISTRIB_DESCRIPTION="Debian GNU/Linux installer" > DISTRIB_RELEASE="12 (bookworm) - installer build 20220624-02:01:58" > X_INSTALLATION_MEDIUM=netboot > > ============================================== > Installer hardware-summary: > ============================================== > uname -a: Linux hclx2 5.18.0-2-arm64 #1 SMP Debian 5.18.5-1 (2022-06-16) > aarch64 GNU/Linux > lsmod: Module Size Used by > lsmod: fuse 131072 0 > lsmod: nls_ascii 16384 1 > lsmod: nls_cp437 20480 1 > lsmod: efivarfs 20480 1 > lsmod: dm_mod 143360 6 > lsmod: dax 36864 1 dm_mod > lsmod: raid1 57344 1 > lsmod: md_mod 167936 4 raid1 > lsmod: xfs 1376256 0 > lsmod: jfs 196608 0 > lsmod: btrfs 1466368 0 > lsmod: xor 20480 1 btrfs > lsmod: xor_neon 20480 1 xor > lsmod: raid6_pq 106496 1 btrfs > lsmod: zstd_compress 253952 1 btrfs > lsmod: libcrc32c 16384 2 btrfs,xfs > lsmod: vfat 28672 1 > lsmod: fat 81920 1 vfat > lsmod: ext4 761856 1 > lsmod: crc16 16384 1 ext4 > lsmod: mbcache 24576 1 ext4 > lsmod: jbd2 143360 1 ext4 > lsmod: crc32c_generic 16384 3 > lsmod: sd_mod 57344 3 > lsmod: t10_pi 20480 1 sd_mod > lsmod: crc64_rocksoft 20480 1 t10_pi > lsmod: crc64 20480 1 crc64_rocksoft > lsmod: crc_t10dif 20480 1 t10_pi > lsmod: crct10dif_common 16384 1 crc_t10dif > lsmod: ahci_qoriq 16384 0 > lsmod: ahci_platform 16384 3 > lsmod: libahci_platform 20480 2 ahci_platform,ahci_qoriq > lsmod: libahci 40960 3 > libahci_platform,ahci_platform,ahci_qoriq > lsmod: libata 303104 4 > libahci,libahci_platform,ahci_platform,ahci_qoriq > lsmod: usb_storage 73728 0 > lsmod: scsi_mod 229376 3 sd_mod,usb_storage,libata > lsmod: scsi_common 16384 3 scsi_mod,usb_storage,libata > lsmod: cdc_ether 20480 0 > lsmod: usbnet 45056 1 cdc_ether > lsmod: r8152 110592 0 > lsmod: mii 20480 2 usbnet,r8152 > lsmod: xhci_plat_hcd 20480 0 > lsmod: xhci_hcd 253952 1 xhci_plat_hcd > lsmod: at803x 32768 0 > lsmod: xgmac_mdio 20480 0 > lsmod: acpi_mdio 16384 1 xgmac_mdio > lsmod: mdio_devres 16384 1 xgmac_mdio > lsmod: of_mdio 20480 2 mdio_devres,xgmac_mdio > lsmod: usbcore 270336 6 > xhci_hcd,usbnet,usb_storage,cdc_ether,xhci_plat_hcd,r8152 > lsmod: fixed_phy 16384 1 of_mdio > lsmod: fwnode_mdio 20480 2 acpi_mdio,of_mdio > lsmod: libphy 98304 6 > mdio_devres,acpi_mdio,fwnode_mdio,of_mdio,fixed_phy,at803x > lsmod: usb_common 16384 3 xhci_hcd,usbcore,xhci_plat_hcd
Which of the many network ports? The module list at least looks like the modules the AR8035 10Gb copper port uses ought to be present. The layerscape ports need to be configured for sure. That stuff looks weird and complicated. What dtb is it using? -- Len Sorensen
