Package: src:linux
Version: 5.10.92-1
Severity: normal
X-Debbugs-Cc: s...@qcontinuum.plus.com
Dear Maintainer,
*** Reporter, please consider answering these questions, where appropriate ***
* What led up to the situation?
Attempting to implement RTS/CTS handshaking
* What exactly did you do (or not do) that was effective (or
ineffective)?
An Arduino board was used. The onboard CH340 chip has pins for RTS
exposed. These were connected to GPIO pins to read the RTS signal
and send a CTS signal to a terminal running on a PC.
The terminal indicates a change of state in the CTS signal but
is not prevented from sending data when the receiver de-asserts
CTS.
The problem was confirmed using both PuTTy and GtkTerm on Linux.
The same hardware and test sketch were used consistently for all
tests and the same problem does NOT occur on Windows so it appears
that the problem may be related to the Linux implementation of the
CH340 driver that is supplied with the kernel module.
Other reports also suggest that XON/XOFF does not work either
but I have not tested this yet personnaly.
* What was the outcome of this action?
The terminal contiunes to send data regardless resulting in data
loss and garbled transmission.
* What outcome did you expect instead?
When CTS is de-asserted, the terminal should not only indicate
the status of the signal but should also STOP sending data
immediately until CTS is asserted again indicating that the
receiver is ready to accept further data.
*** End of the template - remove these template lines ***
-- Package-specific info:
** Version:
Linux version 5.10.0-11-amd64 (debian-ker...@lists.debian.org) (gcc-10 (Debian
10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP
Debian 5.10.92-1 (2022-01-18)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-5.10.0-11-amd64
root=UUID=6b901bb9-7299-43f2-bf38-c5131794f836 ro quiet
** Not tainted
** Kernel log:
[ 2.780566] systemd[1]: Starting Create System Users...
[ 2.816476] systemd[1]: Finished Apply Kernel Variables.
[ 2.818961] systemd[1]: Finished Load/Save Random Seed.
[ 2.819081] systemd[1]: Condition check resulted in First Boot Complete
being skipped.
[ 2.824610] systemd[1]: Finished Create System Users.
[ 2.825303] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 2.862574] systemd[1]: Finished Create Static Device Nodes in /dev.
[ 2.863789] systemd[1]: Starting Rule-based Manager for Device Events and
Files...
[ 2.899087] systemd[1]: Finished Coldplug All udev Devices.
[ 2.900333] systemd[1]: Starting Helper to synchronize boot up for
ifupdown...
[ 2.917684] systemd[1]: Finished Helper to synchronize boot up for ifupdown.
[ 2.957344] systemd[1]: Finished Set the console keyboard layout.
[ 2.957438] systemd[1]: Reached target Local File Systems (Pre).
[ 2.957450] systemd[1]: Reached target Local File Systems.
[ 2.958031] systemd[1]: Starting Load AppArmor profiles...
[ 2.958661] systemd[1]: Starting Set console font and keymap...
[ 2.959322] systemd[1]: Starting Tell Plymouth To Write Out Runtime Data...
[ 2.959374] systemd[1]: Condition check resulted in Store a System Token in
an EFI Variable being skipped.
[ 2.959420] systemd[1]: Condition check resulted in Commit a transient
machine-id on disk being skipped.
[ 2.966636] systemd[1]: Started Journal Service.
[ 2.985588] systemd-journald[218]: Received client request to flush runtime
journal.
[ 3.002491] systemd-journald[218]: File
/var/log/journal/d13d99363a7b4181a08b88c2176ef752/system.journal corrupted or
uncleanly shut down, renaming and replacing.
[ 3.370762] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 3.531303] iTCO_vendor_support: vendor-support=0
[ 3.537461] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 3.537530] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0660)
[ 3.537627] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 3.617148] Adding 998396k swap on /dev/vda5. Priority:-2 extents:1
across:998396k FS
[ 3.657076] RAPL PMU: API unit is 2^-32 Joules, 0 fixed counters,
10737418240 ms ovfl timer
[ 3.685079] cryptd: max_cpu_qlen set to 1000
[ 3.740477] AVX2 version of gcm_enc/dec engaged.
[ 3.740480] AES CTR mode by8 optimization enabled
[ 3.808523] audit: type=1400 audit(1645817008.436:2): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-soffice"
pid=263 comm="apparmor_parser"
[ 3.808525] audit: type=1400 audit(1645817008.436:3): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-soffice//gpg"
pid=263 comm="apparmor_parser"
[ 3.823150] audit: type=1400 audit(1645817008.452:4): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-oopslash"
pid=328 comm="apparmor_parser"
[ 3.837793] audit: type=1400 audit(1645817008.468:5): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=338
comm="apparmor_parser"
[ 3.837796] audit: type=1400 audit(1645817008.468:6): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod"
pid=338 comm="apparmor_parser"
[ 3.846387] audit: type=1400 audit(1645817008.476:7): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="lsb_release" pid=347
comm="apparmor_parser"
[ 3.853794] snd_hda_codec_generic hdaudioC0D0: autoconfig for Generic:
line_outs=1 (0x3/0x0/0x0/0x0/0x0) type:line
[ 3.853796] snd_hda_codec_generic hdaudioC0D0: speaker_outs=0
(0x0/0x0/0x0/0x0/0x0)
[ 3.853797] snd_hda_codec_generic hdaudioC0D0: hp_outs=0
(0x0/0x0/0x0/0x0/0x0)
[ 3.853798] snd_hda_codec_generic hdaudioC0D0: mono: mono_out=0x0
[ 3.853798] snd_hda_codec_generic hdaudioC0D0: inputs:
[ 3.853800] snd_hda_codec_generic hdaudioC0D0: Line=0x5
[ 3.862386] audit: type=1400 audit(1645817008.492:8): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport"
pid=358 comm="apparmor_parser"
[ 3.890218] audit: type=1400 audit(1645817008.520:9): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=370
comm="apparmor_parser"
[ 3.890221] audit: type=1400 audit(1645817008.520:10): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_filter" pid=370
comm="apparmor_parser"
[ 8.597444] rfkill: input handler disabled
[ 18.689014] rfkill: input handler enabled
[ 21.267957] rfkill: input handler disabled
[ 34.332945] usb 1-3: new full-speed USB device number 3 using xhci_hcd
[ 34.541148] usb 1-3: New USB device found, idVendor=1a86, idProduct=7523,
bcdDevice= 2.63
[ 34.541154] usb 1-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 34.541156] usb 1-3: Product: USB2.0-Serial
[ 34.572448] usbcore: registered new interface driver usbserial_generic
[ 34.572818] usbserial: USB Serial support registered for generic
[ 34.575978] usbcore: registered new interface driver ch341
[ 34.576346] usbserial: USB Serial support registered for ch341-uart
[ 34.576448] ch341 1-3:1.0: ch341-uart converter detected
[ 34.581782] usb 1-3: ch341-uart converter now attached to ttyUSB0
[ 899.714674] usb 1-3: USB disconnect, device number 3
[ 899.715125] ch341-uart ttyUSB0: ch341-uart converter now disconnected from
ttyUSB0
[ 899.715154] ch341 1-3:1.0: device disconnected
[ 907.022364] usb 1-3: new full-speed USB device number 4 using xhci_hcd
[ 907.233692] usb 1-3: New USB device found, idVendor=1a86, idProduct=7523,
bcdDevice= 2.63
[ 907.233696] usb 1-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 907.233699] usb 1-3: Product: USB2.0-Serial
[ 907.238524] ch341 1-3:1.0: ch341-uart converter detected
[ 907.241976] usb 1-3: ch341-uart converter now attached to ttyUSB0
[ 932.137876] usb 1-3: USB disconnect, device number 4
[ 932.138191] ch341-uart ttyUSB0: ch341-uart converter now disconnected from
ttyUSB0
[ 932.138217] ch341 1-3:1.0: device disconnected
[ 936.644998] usb 1-3: new full-speed USB device number 5 using xhci_hcd
[ 936.866061] usb 1-3: New USB device found, idVendor=0403, idProduct=6001,
bcdDevice= 6.00
[ 936.866065] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 936.866067] usb 1-3: Product: FT232R USB UART
[ 936.866068] usb 1-3: Manufacturer: FTDI
[ 936.866069] usb 1-3: SerialNumber: A5XK3RJT
[ 936.902489] usbcore: registered new interface driver ftdi_sio
[ 936.905150] usbserial: USB Serial support registered for FTDI USB Serial
Device
[ 936.905559] ftdi_sio 1-3:1.0: FTDI USB Serial Device converter detected
[ 936.905725] usb 1-3: Detected FT232RL
[ 936.908655] usb 1-3: FTDI USB Serial Device converter now attached to ttyUSB0
[ 968.997123] usb 1-3: USB disconnect, device number 5
[ 968.999581] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now
disconnected from ttyUSB0
[ 968.999621] ftdi_sio 1-3:1.0: device disconnected
[ 971.215421] usb 1-3: new full-speed USB device number 6 using xhci_hcd
[ 971.445486] usb 1-3: New USB device found, idVendor=1a86, idProduct=7523,
bcdDevice= 2.63
[ 971.445491] usb 1-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 971.445494] usb 1-3: Product: USB2.0-Serial
[ 971.449157] ch341 1-3:1.0: ch341-uart converter detected
[ 971.452867] usb 1-3: ch341-uart converter now attached to ttyUSB0
[ 1200.609126] rfkill: input handler enabled
[ 1203.006584] rfkill: input handler disabled
[ 1208.474956] rfkill: input handler enabled
[ 1211.026658] rfkill: input handler disabled
[ 1551.609588] rfkill: input handler enabled
[ 1554.075540] rfkill: input handler disabled
[ 1587.676093] rfkill: input handler enabled
[ 1590.649444] rfkill: input handler disabled
** Model information
sys_vendor: QEMU
product_name: Standard PC (Q35 + ICH9, 2009)
product_version: pc-q35-4.2
chassis_vendor: QEMU
chassis_version: pc-q35-4.2
bios_vendor: SeaBIOS
bios_version: 1.13.0-1ubuntu1.1
** Loaded modules:
ftdi_sio
ch341
usbserial
rfkill
intel_rapl_msr
intel_rapl_common
kvm_intel
kvm
irqbypass
ghash_clmulni_intel
snd_hda_codec_generic
ledtrig_audio
snd_hda_intel
snd_intel_dspcfg
soundwire_intel
soundwire_generic_allocation
snd_soc_core
aesni_intel
snd_compress
soundwire_cadence
libaes
crypto_simd
cryptd
glue_helper
rapl
snd_hda_codec
snd_hda_core
snd_hwdep
joydev
soundwire_bus
iTCO_wdt
snd_pcm
intel_pmc_bxt
iTCO_vendor_support
watchdog
virtio_balloon
snd_timer
virtio_console
snd
soundcore
serio_raw
pcspkr
evdev
qemu_fw_cfg
msr
fuse
configfs
virtio_rng
rng_core
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
hid_generic
usbhid
hid
qxl
drm_ttm_helper
ttm
drm_kms_helper
cec
ahci
xhci_pci
libahci
drm
xhci_hcd
virtio_net
libata
virtio_blk
net_failover
failover
crct10dif_pclmul
crct10dif_common
psmouse
crc32_pclmul
scsi_mod
crc32c_intel
i2c_i801
i2c_smbus
lpc_ich
usbcore
usb_common
virtio_pci
virtio_ring
virtio
button
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller [8086:29c0]
Subsystem: Red Hat, Inc. QEMU Virtual Machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.0 VGA compatible controller [0300]: Red Hat, Inc. QXL paravirtual graphic
card [1b36:0100] (rev 04) (prog-if 00 [VGA controller])
Subsystem: Red Hat, Inc. QEMU Virtual Machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=64M]
Region 1: Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
Region 2: Memory at fce14000 (32-bit, non-prefetchable) [size=8K]
Region 3: I/O ports at c040 [size=32]
Expansion ROM at 000c0000 [disabled] [size=128K]
Kernel driver in use: qxl
Kernel modules: qxl
00:02.0 PCI bridge [0604]: Red Hat, Inc. QEMU PCIe Root port [1b36:000c]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fce16000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff [size=4K]
Memory behind bridge: fcc00000-fcdfffff [size=2M]
Prefetchable memory behind bridge: 00000000fea00000-00000000febfffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.1 PCI bridge [0604]: Red Hat, Inc. QEMU PCIe Root port [1b36:000c]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fce17000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff [size=4K]
Memory behind bridge: fca00000-fcbfffff [size=2M]
Prefetchable memory behind bridge: 00000000fe800000-00000000fe9fffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.2 PCI bridge [0604]: Red Hat, Inc. QEMU PCIe Root port [1b36:000c]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fce18000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff [size=4K]
Memory behind bridge: fc800000-fc9fffff [size=2M]
Prefetchable memory behind bridge: 00000000fe600000-00000000fe7fffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.3 PCI bridge [0604]: Red Hat, Inc. QEMU PCIe Root port [1b36:000c]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fce19000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00004000-00004fff [size=4K]
Memory behind bridge: fc600000-fc7fffff [size=2M]
Prefetchable memory behind bridge: 00000000fe400000-00000000fe5fffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.4 PCI bridge [0604]: Red Hat, Inc. QEMU PCIe Root port [1b36:000c]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fce1a000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00005000-00005fff [size=4K]
Memory behind bridge: fc400000-fc5fffff [size=2M]
Prefetchable memory behind bridge: 00000000fe200000-00000000fe3fffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.5 PCI bridge [0604]: Red Hat, Inc. QEMU PCIe Root port [1b36:000c]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fce1b000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 00006000-00006fff [size=4K]
Memory behind bridge: fc200000-fc3fffff [size=2M]
Prefetchable memory behind bridge: 00000000fe000000-00000000fe1fffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.6 PCI bridge [0604]: Red Hat, Inc. QEMU PCIe Root port [1b36:000c]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fce1c000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 00007000-00007fff [size=4K]
Memory behind bridge: fc000000-fc1fffff [size=2M]
Prefetchable memory behind bridge: 00000000fde00000-00000000fdffffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio
Controller [8086:293e] (rev 03)
Subsystem: Red Hat, Inc. QEMU Virtual Machine [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at fce10000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IB (ICH9) LPC Interface
Controller [8086:2918] (rev 02)
Subsystem: Red Hat, Inc. QEMU Virtual Machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6
port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Red Hat, Inc. QEMU Virtual Machine [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 36
Region 4: I/O ports at c060 [size=32]
Region 5: Memory at fce1d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller
[8086:2930] (rev 02)
Subsystem: Red Hat, Inc. QEMU Virtual Machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 0700 [size=64]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 Ethernet controller [0200]: Red Hat, Inc. Virtio network device
[1af4:1041] (rev 01)
Subsystem: Red Hat, Inc. Virtio network device [1af4:1100]
Physical Slot: 0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 1: Memory at fcc80000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fea00000 (64-bit, prefetchable) [size=16K]
Expansion ROM at fcc00000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
02:00.0 USB controller [0c03]: Red Hat, Inc. QEMU XHCI Host Controller
[1b36:000d] (rev 01) (prog-if 30 [XHCI])
Subsystem: Red Hat, Inc. QEMU XHCI Host Controller [1af4:1100]
Physical Slot: 0-1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fca00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
03:00.0 Communication controller [0780]: Red Hat, Inc. Virtio console
[1af4:1043] (rev 01)
Subsystem: Red Hat, Inc. Virtio console [1af4:1100]
Physical Slot: 0-2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 1: Memory at fc800000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe600000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
04:00.0 SCSI storage controller [0100]: Red Hat, Inc. Virtio block device
[1af4:1042] (rev 01)
Subsystem: Red Hat, Inc. Virtio block device [1af4:1100]
Physical Slot: 0-3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 1: Memory at fc600000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe400000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
05:00.0 Unclassified device [00ff]: Red Hat, Inc. Virtio memory balloon
[1af4:1045] (rev 01)
Subsystem: Red Hat, Inc. Virtio memory balloon [1af4:1100]
Physical Slot: 0-4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 4: Memory at fe200000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
06:00.0 Unclassified device [00ff]: Red Hat, Inc. Virtio RNG [1af4:1044] (rev
01)
Subsystem: Red Hat, Inc. Virtio RNG [1af4:1100]
Physical Slot: 0-5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 4: Memory at fe000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
** USB devices:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 006: ID 1a86:7523 QinHeng Electronics CH340 serial converter
Bus 001 Device 002: ID 0627:0001 Adomax Technology Co., Ltd QEMU USB Tablet
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 11.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 5.10.0-11-amd64 (SMP w/1 CPU thread)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8),
LANGUAGE=en_GB:en
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-5.10.0-11-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.140
ii kmod 28-1
ii linux-base 4.6
Versions of packages linux-image-5.10.0-11-amd64 recommends:
ii apparmor 2.13.6-10
ii firmware-linux-free 20200122-1
Versions of packages linux-image-5.10.0-11-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.04-20
pn linux-doc-5.10 <none>
Versions of packages linux-image-5.10.0-11-amd64 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
