Package: src:linux
Version: 5.9.1-1
Severity: important
X-Debbugs-Cc: alx.manpa...@gmail.com

Dear Maintainer,

*** Reporter, please consider answering these questions, where appropriate ***

   * What led up to the situation?

        When I upgreeaded from kernel 5.6 to 5.7 a long time ago, my system 
broke.
        I first saw some firmware errors when booting.
        But when I fixed those firmware errors by adding non-free and contrib 
repos,
        and installing firmware-linux,
        those errors disapeared.
        Now it simply goes black at some point during the boot.
        If I boot with linux 5.6, however, everything runs fine.


   * What exactly did you do (or not do) that was effective (or
     ineffective)?
   * What was the outcome of this action?
   * What outcome did you expect instead?

        Ineffective: Upgrading the kernel to 5.8, or 5.9.
                None of the kernels >= 5.7 work.

        Worked: Run with kernel 5.6 (or older).

        Ineffective: Clean install from DI-alpha2.
                This provides two kernels: 5.4 (works) and 5.9 (doesn't work).

        I also tried installing firmware directly from kernel.org:
                
git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
                sudo make install
        but it didn't fix it.

*** End of the template - remove these template lines ***


-- Package-specific info:
** Kernel log: boot messages should be attached
        I don't know how to get the boot messages from a system that doesn't 
boot.

** Model information
sys_vendor: ASUS
product_name: All Series
product_version: System Version
chassis_vendor: To Be Filled By O.E.M.
chassis_version: To Be Filled By O.E.M.
bios_vendor: American Megatrends Inc.
bios_version: 2902
board_vendor: ASUSTeK COMPUTER INC.
board_name: Z97M-PLUS
board_version: Rev X.0x

** Network interface configuration:
*** /etc/network/interfaces:

source /etc/network/interfaces.d/*

auto lo
iface lo inet loopback

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Broadwell-U Host Bridge - DMI 
[8086:1610] (rev 0a)
        Subsystem: ASUSTeK Computer Inc. Broadwell-U Host Bridge - DMI 
[1043:8534]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: <access denied>

00:01.0 PCI bridge [0604]: Intel Corporation Broadwell-U PCI Express x16 
Controller [8086:1601] (rev 0a) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 24
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000e000-0000efff [size=4K]
        Memory behind bridge: f7100000-f71fffff [size=1M]
        Prefetchable memory behind bridge: [disabled]
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>
        Kernel driver in use: pcieport

00:02.0 VGA compatible controller [0300]: Intel Corporation Iris Pro Graphics 
6200 [8086:1622] (rev 0a) (prog-if 00 [VGA controller])
        DeviceName:  Onboard IGD
        Subsystem: ASUSTeK Computer Inc. Iris Pro Graphics 6200 [1043:8534]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 36
        Region 0: Memory at f6000000 (64-bit, non-prefetchable) [size=16M]
        Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
        Region 4: I/O ports at f000 [size=64]
        Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
        Capabilities: <access denied>
        Kernel driver in use: i915
        Kernel modules: i915

00:03.0 Audio device [0403]: Intel Corporation Broadwell-U Audio Controller 
[8086:160c] (rev 0a)
        Subsystem: ASUSTeK Computer Inc. Broadwell-U Audio Controller 
[1043:8534]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 39
        Region 0: Memory at f7234000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>
        Kernel driver in use: snd_hda_intel
        Kernel modules: snd_hda_intel

00:14.0 USB controller [0c03]: Intel Corporation 9 Series Chipset Family USB 
xHCI Controller [8086:8cb1] (prog-if 30 [XHCI])
        Subsystem: ASUSTeK Computer Inc. 9 Series Chipset Family USB xHCI 
Controller [1043:8534]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 29
        Region 0: Memory at f7220000 (64-bit, non-prefetchable) [size=64K]
        Capabilities: <access denied>
        Kernel driver in use: xhci_hcd
        Kernel modules: xhci_pci

00:16.0 Communication controller [0780]: Intel Corporation 9 Series Chipset 
Family ME Interface #1 [8086:8cba]
        Subsystem: ASUSTeK Computer Inc. 9 Series Chipset Family ME Interface 
[1043:8534]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 35
        Region 0: Memory at f723d000 (64-bit, non-prefetchable) [size=16]
        Capabilities: <access denied>
        Kernel driver in use: mei_me
        Kernel modules: mei_me

00:19.0 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2) 
I218-V [8086:15a1]
        DeviceName:  Onboard LAN
        Subsystem: ASUSTeK Computer Inc. Ethernet Connection (2) I218-V 
[1043:85c4]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 28
        Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=128K]
        Region 1: Memory at f723b000 (32-bit, non-prefetchable) [size=4K]
        Region 2: I/O ports at f060 [size=32]
        Capabilities: <access denied>
        Kernel driver in use: e1000e
        Kernel modules: e1000e

00:1a.0 USB controller [0c03]: Intel Corporation 9 Series Chipset Family USB 
EHCI Controller #2 [8086:8cad] (prog-if 20 [EHCI])
        Subsystem: ASUSTeK Computer Inc. 9 Series Chipset Family USB EHCI 
Controller [1043:8534]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f723a000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: <access denied>
        Kernel driver in use: ehci-pci
        Kernel modules: ehci_pci

00:1b.0 Audio device [0403]: Intel Corporation 9 Series Chipset Family HD Audio 
Controller [8086:8ca0]
        Subsystem: ASUSTeK Computer Inc. 9 Series Chipset Family HD Audio 
Controller [1043:8630]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 38
        Region 0: Memory at f7230000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>
        Kernel driver in use: snd_hda_intel
        Kernel modules: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation 9 Series Chipset Family PCI 
Express Root Port 1 [8086:8c90] (rev d0) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 25
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: [disabled]
        Memory behind bridge: [disabled]
        Prefetchable memory behind bridge: [disabled]
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>
        Kernel driver in use: pcieport

00:1c.3 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 
d0) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin D routed to IRQ 26
        Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
        I/O behind bridge: [disabled]
        Memory behind bridge: [disabled]
        Prefetchable memory behind bridge: [disabled]
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>
        Kernel driver in use: pcieport

00:1c.4 PCI bridge [0604]: Intel Corporation 9 Series Chipset Family PCI 
Express Root Port 5 [8086:8c98] (rev d0) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 27
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
        I/O behind bridge: [disabled]
        Memory behind bridge: f7000000-f70fffff [size=1M]
        Prefetchable memory behind bridge: [disabled]
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>
        Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation 9 Series Chipset Family USB 
EHCI Controller #1 [8086:8ca6] (prog-if 20 [EHCI])
        Subsystem: ASUSTeK Computer Inc. 9 Series Chipset Family USB EHCI 
Controller [1043:8534]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at f7239000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: <access denied>
        Kernel driver in use: ehci-pci
        Kernel modules: ehci_pci

00:1f.0 ISA bridge [0601]: Intel Corporation Z97 Chipset LPC Controller 
[8086:8cc4]
        Subsystem: ASUSTeK Computer Inc. Z97 Chipset LPC Controller [1043:8534]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: <access denied>
        Kernel driver in use: lpc_ich
        Kernel modules: lpc_ich

00:1f.3 SMBus [0c05]: Intel Corporation 9 Series Chipset Family SMBus 
Controller [8086:8ca2]
        Subsystem: ASUSTeK Computer Inc. 9 Series Chipset Family SMBus 
Controller [1043:8534]
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin C routed to IRQ 18
        Region 0: Memory at f7238000 (64-bit, non-prefetchable) [size=256]
        Region 4: I/O ports at f040 [size=32]
        Kernel driver in use: i801_smbus
        Kernel modules: i2c_i801

01:00.0 Non-Volatile memory controller [0108]: Samsung Electronics Co Ltd NVMe 
SSD Controller SM951/PM951 [144d:a802] (rev 01) (prog-if 02 [NVM Express])
        Subsystem: Samsung Electronics Co Ltd NVMe SSD Controller SM951/PM951 
[144d:a801]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 16
        NUMA node: 0
        Region 0: Memory at f7110000 (64-bit, non-prefetchable) [size=16K]
        Region 2: I/O ports at e000 [size=256]
        Expansion ROM at f7100000 [disabled] [size=64K]
        Capabilities: <access denied>
        Kernel driver in use: nvme
        Kernel modules: nvme

03:00.0 PCI bridge [0604]: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI 
Bridge [1b21:1080] (rev 04) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 255
        Bus: primary=03, secondary=04, subordinate=04, sec-latency=32
        I/O behind bridge: [disabled]
        Memory behind bridge: [disabled]
        Prefetchable memory behind bridge: [disabled]
        Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>

05:00.0 Network controller [0280]: Intel Corporation Wireless 7260 [8086:08b1] 
(rev bb)
        Subsystem: Intel Corporation Dual Band Wireless-AC 7260 [8086:4070]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 37
        Region 0: Memory at f7000000 (64-bit, non-prefetchable) [size=8K]
        Capabilities: <access denied>
        Kernel driver in use: iwlwifi
        Kernel modules: iwlwifi


** USB devices:
Bus 004 Device 002: ID 8087:8001 Intel Corp. Integrated Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 8087:8009 Intel Corp. 
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. ASM1051E SATA 6Gb/s 
bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 
6Gb/s bridge
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 04b4:4009 Cypress Semiconductor Corp. 
Bus 001 Device 003: ID 04d9:a09f Holtek Semiconductor, Inc. E-Signal LUOM G10 
Mechanical Gaming Mouse
Bus 001 Device 002: ID 8087:07dc Intel Corp. Bluetooth wireless interface
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: bullseye/sid
  APT prefers testing
  APT policy: (500, 'testing')
Architecture: amd64 (x86_64)

Kernel: Linux 5.4.0-4-amd64 (SMP w/4 CPU threads)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), 
LANGUAGE=en_US:en
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled

Versions of packages linux-image-5.9.0-1-amd64 depends on:
ii  initramfs-tools [linux-initramfs-tool]  0.139
ii  kmod                                    27+20200310-2
ii  linux-base                              4.6

Versions of packages linux-image-5.9.0-1-amd64 recommends:
ii  apparmor             2.13.5-1
ii  firmware-linux-free  20200122-1

Versions of packages linux-image-5.9.0-1-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  grub-efi-amd64          2.04-8
pn  linux-doc-5.9           <none>

Versions of packages linux-image-5.9.0-1-amd64 is related to:
ii  firmware-amd-graphics     20200918-1
pn  firmware-atheros          <none>
pn  firmware-bnx2             <none>
pn  firmware-bnx2x            <none>
pn  firmware-brcm80211        <none>
pn  firmware-cavium           <none>
pn  firmware-intel-sound      <none>
pn  firmware-intelwimax       <none>
pn  firmware-ipw2x00          <none>
pn  firmware-ivtv             <none>
pn  firmware-iwlwifi          <none>
pn  firmware-libertas         <none>
ii  firmware-linux-nonfree    20200918-1
ii  firmware-misc-nonfree     20200918-1
pn  firmware-myricom          <none>
pn  firmware-netxen           <none>
pn  firmware-qlogic           <none>
pn  firmware-realtek          <none>
pn  firmware-samsung          <none>
pn  firmware-siano            <none>
pn  firmware-ti-connectivity  <none>
pn  xen-hypervisor            <none>

-- no debconf information

Reply via email to