Package: ifupdown Version: 0.8.34 Severity: important Hi,
I have a Debian live system (using live-boot) launched in QEMU with a static network configuration. live-boot brings up the network interface ens3 in the initrd to fetch the squashfs root image. The [email protected] fails: ``` $ systemctl status [email protected] ● [email protected] - ifup for ens3 Loaded: loaded (/lib/systemd/system/[email protected]; static; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2019-01-18 15:26:29 UTC; 9min ago Process: 696 ExecStart=/bin/sh -ec ifup --allow=hotplug ens3; ifquery --state ens3 (code=exited, status=1/FAILURE) Main PID: 696 (code=exited, status=1/FAILURE) Jan 18 15:26:29 systemd[1]: Started ifup for ens3. Jan 18 15:26:29 systemd[1]: [email protected]: Main process exited, code=exited, status=1/FAILURE Jan 18 15:26:29 systemd[1]: [email protected]: Failed with result 'exit-code'. ``` Adding --verbose to ifup and ifquery revealed that ifquery fails with exit code 1, but does not produce any output. The journal shows that [email protected] exits before ens3 is ready: ``` Jan 18 15:26:29 systemd[1]: Started ifup for ens3. Jan 18 15:26:29 systemd[1]: [email protected]: Main process exited, code=exited, status=1/FAILURE Jan 18 15:26:29 systemd[1]: [email protected]: Failed with result 'exit-code'. Jan 18 15:26:30 systemd-udevd[491]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. Jan 18 15:26:30 systemd-udevd[491]: Could not generate persistent MAC address for ethoipsix0: No such file or directory Jan 18 15:26:30 kernel: IPv6: ADDRCONF(NETDEV_UP): ens3: link is not ready Jan 18 15:26:30 kernel: e1000: ens3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX Jan 18 15:26:30 kernel: IPv6: ADDRCONF(NETDEV_CHANGE): ens3: link becomes ready ``` -- Package-specific info: --- /etc/network/interfaces: # interfaces(5) file used by ifup(8) and ifdown(8) # Include files from /etc/network/interfaces.d: source-directory /etc/network/interfaces.d # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto ens3 iface ens3 inet static address 10.91.240.1/22 pre-up ip address flush dev $IFACE up ip route add 10.0.0.0/8 via 10.91.243.254 dev $IFACE up ip route add 192.168.0.0/16 via 10.91.243.254 dev $IFACE up sysctl -w net.ipv4.conf.ens3.forwarding=0 --- up and down scripts installed: /etc/network/if-down.d: total 1 -rwxr-xr-x 1 root root 256 Apr 1 2016 resolvconf /etc/network/if-post-down.d: total 0 /etc/network/if-pre-up.d: total 1 -rwxr-xr-x 1 root root 344 Jun 30 2016 ethtool /etc/network/if-up.d: total 3 -rwxr-xr-x 1 root root 817 Apr 1 2016 000resolvconf -rwxr-xr-x 1 root root 1685 Jun 30 2016 ethtool -- System Information: Debian Release: buster/sid APT prefers testing APT policy: (500, 'testing') Architecture: amd64 (x86_64) Kernel: Linux 4.19.0-1-amd64 (SMP w/4 CPU cores) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages ifupdown depends on: ii adduser 3.118 ii iproute2 4.20.0-2 ii libc6 2.28-5 ii lsb-base 10.2018112800 Versions of packages ifupdown recommends: ii isc-dhcp-client [dhcp-client] 4.4.1-2 Versions of packages ifupdown suggests: pn ppp <none> pn rdnssd <none> -- no debconf information
