Package: src:linux Version: 4.17.8-1~bpo9+1 Severity: normal Dear Maintainer,
* What led up to the situation?
A kernel update a few weeks ago (I think).
* What exactly did you do (or not do) that was effective (or
ineffective)?
Powering up externel harddrives connected via eSATA.
* What was the outcome of this action?
For the newer drive: nothing, except the LED on the drive turning on
(presumably the kernel needs to tell that drive to spin up).
For the older drive: the disk spinning up.
In both cases: the drive was not detected (/proc/partitions unchanged),
and no messages appeared in dmesg.
* What outcome did you expect instead?
The drives appearing in /proc/partitions, and messages in dmesg detailing
the detection process, at least after a minute or so.
The machine is a Dell Latitude E6430.
The newer drive is connected to the eSATA port on the Laptop, the older to the
one on the docking station.
Successful workarounds:
- Booting with older linux-image-4.16.0-0.bpo.2-amd64 (4.16.16-2~bpo9+1)
- Booting with linux-image-4.17.0-0.bpo.1-amd64 (4.17.8-1~bpo9+1) and
"ahci.mobile_lpm_policy=1" (as suggested in #904600)
- Booting with linux-image-4.17.0-0.bpo.1-amd64 (4.17.8-1~bpo9+1) and
"ahci.mobile_lpm_policy=0" (as suggested in
/usr/share/doc/linux-image-4.17.0-0.bpo.1-amd64/changelog.Debian.gz)
There a various bug reports that report boot failures; this report differs in
that I can boot fine from the internal harddrive, only drives connected via
eSATA seem to be affected.
This seems to be related to the kernel patch "Improve battery life on laptops"
(see #898629). It was tested by fedora on the same machine model (Latitude
E6430, see (https://fedoraproject.org/wiki/Changes/ImprovedLaptopBatteryLife),
but maybe they only checked the internal harddrives.
The dmesg output below is from the 4.17 kernel with ahci.mobile_lpm_policy=0.
It includes a successfull detection of the older drive (ST3000DM001-9YN166).
The newer harddrive is a ST3000DM001-9YN166.
Regards,
Jö.
-- Package-specific info:
** Version:
Linux version 4.17.0-0.bpo.1-amd64 (debian-ker...@lists.debian.org) (gcc
version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP Debian 4.17.8-1~bpo9+1
(2018-07-23)
** Command line:
BOOT_IMAGE=/vmlinuz-4.17.0-0.bpo.1-amd64
root=UUID=3d183efa-7e39-4dc1-9e3e-46b0fb096d32 ro ahci.mobile_lpm_policy=0 quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 39.831009] input: HDA Intel PCH Dock Line Out as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[ 39.831042] input: HDA Intel PCH Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[ 40.227897] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 40.763149] Bluetooth: Core ver 2.22
[ 40.763166] NET: Registered protocol family 31
[ 40.763168] Bluetooth: HCI device and connection manager initialized
[ 40.763172] Bluetooth: HCI socket layer initialized
[ 40.763174] Bluetooth: L2CAP socket layer initialized
[ 40.763182] Bluetooth: SCO socket layer initialized
[ 40.811487] usbcore: registered new interface driver btusb
[ 40.927673] input: PC Speaker as /devices/platform/pcspkr/input/input18
[ 41.609171] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms
ovfl timer
[ 41.609173] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 41.609174] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 41.609175] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 42.324692] intel_rapl: Found RAPL domain package
[ 42.324694] intel_rapl: Found RAPL domain core
[ 42.324696] intel_rapl: Found RAPL domain uncore
[ 42.324701] intel_rapl: RAPL package 0 domain package locked by BIOS
[ 42.377118] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts:
(null)
[ 42.558682] dcdbas dcdbas: Dell Systems Management Base Driver (version
5.6.0-3.2)
[ 42.702690] dell-smbios A80593CE-A997-11DA-B012-B622A1EF5492: WMI SMBIOS
userspace interface not supported(0), try upgrading to a newer BIOS
[ 42.761796] dell_laptop: Using dell-rbtn acpi driver for receiving events
[ 44.772993] iTCO_vendor_support: vendor-support=0
[ 44.831386] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 44.831445] iTCO_wdt: Found a Panther Point TCO device (Version=2,
TCOBASE=0x0460)
[ 44.831580] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 46.219256] input: Dell WMI hotkeys as
/devices/platform/PNP0C14:00/wmi_bus/wmi_bus-PNP0C14:00/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input19
[ 47.104553] Adding 7998284k swap on /dev/mapper/Swap. Priority:-2 extents:1
across:7998284k FS
[ 47.653783] audit: type=1400 audit(1535371388.166:2): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/bin/freshclam"
pid=2344 comm="apparmor_parser"
[ 48.210596] audit: type=1400 audit(1535371388.722:3): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="system_tor" pid=2294
comm="apparmor_parser"
[ 48.270989] b43-phy0: Broadcom 43228 WLAN found (core revision 30)
[ 48.271418] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 16
[ 48.271430] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9,
Version 1
[ 48.272726] Broadcom 43xx driver loaded [ Features: PNLS ]
[ 48.287293] audit: type=1400 audit(1535371388.798:4): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/bin/obfsproxy"
pid=2296 comm="apparmor_parser"
[ 48.536772] b43 bcma0:1: firmware: direct-loading firmware
b43/ucode30_mimo.fw
[ 48.559795] b43 bcma0:1: firmware: direct-loading firmware
b43/n16initvals30.fw
[ 48.560616] b43 bcma0:1: firmware: direct-loading firmware
b43/n16bsinitvals30.fw
[ 48.698000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 48.919753] audit: type=1400 audit(1535371389.430:5): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed"
pid=2481 comm="apparmor_parser"
[ 49.500461] b43 bcma0:1 wlan1: renamed from wlan0
[ 49.675924] audit: type=1400 audit(1535371390.186:6): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/sbin/ntpd" pid=2542
comm="apparmor_parser"
[ 49.812729] audit: type=1400 audit(1535371390.326:7): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/cups/backend/cups-pdf" pid=2492 comm="apparmor_parser"
[ 49.813526] audit: type=1400 audit(1535371390.326:8): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=2492
comm="apparmor_parser"
[ 49.813817] audit: type=1400 audit(1535371390.326:9): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/sbin/cupsd//third_party" pid=2492 comm="apparmor_parser"
[ 49.879134] audit: type=1400 audit(1535371390.390:10): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/telepathy/mission-control-5" pid=2445 comm="apparmor_parser"
[ 49.879629] audit: type=1400 audit(1535371390.390:11): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/telepathy/telepathy-*" pid=2445 comm="apparmor_parser"
[ 61.636875] do_IRQ: 3.37 No irq handler for vector
[ 62.830561] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 62.830562] Bluetooth: BNEP filters: protocol multicast
[ 62.830566] Bluetooth: BNEP socket layer initialized
[ 76.605012] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 76.864286] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 76.918402] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 79.610127] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
None
[ 79.610165] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 148.087697] ata6: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe
frozen
[ 148.089001] ata6: irq_stat 0x00400040, connection status changed
[ 148.090316] ata6: SError: { PHYRdyChg CommWake DevExch }
[ 148.091632] ata6: hard resetting link
[ 153.842321] ata6: link is slow to respond, please be patient (ready=0)
[ 158.102358] ata6: COMRESET failed (errno=-16)
[ 158.103679] ata6: hard resetting link
[ 159.894373] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 159.895387] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 159.895391] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 159.895393] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 159.895607] ata6.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device
(Stat=0x51 Err=0x04)
[ 159.896435] ata6.00: ATA-8: ST3000DM001-9YN166, CC4C, max UDMA/133
[ 159.896437] ata6.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 159.897482] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 159.897485] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 159.897487] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 159.897628] ata6.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device
(Stat=0x51 Err=0x04)
[ 159.898253] ata6.00: configured for UDMA/133
[ 159.898290] ata6: EH complete
[ 159.898546] scsi 5:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC4C
PQ: 0 ANSI: 5
[ 159.898966] sd 5:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00
TB/2.73 TiB)
[ 159.898968] sd 5:0:0:0: [sdb] 4096-byte physical blocks
[ 159.898976] sd 5:0:0:0: [sdb] Write Protect is off
[ 159.898978] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 159.898990] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 159.899069] sd 5:0:0:0: Attached scsi generic sg1 type 0
[ 159.944224] sdb: sdb1
[ 159.944572] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 252.038128] ata6: exception Emask 0x10 SAct 0x0 SErr 0x4090000 action 0xe
frozen
[ 252.038133] ata6: irq_stat 0x00400040, connection status changed
[ 252.038136] ata6: SError: { PHYRdyChg 10B8B DevExch }
[ 252.038140] ata6: hard resetting link
[ 252.747443] ata6: SATA link down (SStatus 0 SControl 300)
[ 257.759491] ata6: hard resetting link
[ 258.075026] ata6: SATA link down (SStatus 0 SControl 300)
[ 263.135507] ata6: hard resetting link
[ 263.450367] ata6: SATA link down (SStatus 0 SControl 300)
[ 263.450376] ata6.00: disabled
[ 263.450390] ata6: EH complete
[ 263.450404] ata6.00: detaching (SCSI 5:0:0:0)
[ 263.451087] sd 5:0:0:0: [sdb] Stopping disk
[ 263.451107] sd 5:0:0:0: [sdb] Start/Stop Unit failed: Result:
hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
** Model information
sys_vendor: Dell Inc.
product_name: Latitude E6430
product_version: 01
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: A13
board_vendor: Dell Inc.
board_name: 0H3MT5
board_version: A00
** Loaded modules:
xt_multiport
snd_hrtimer
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_seq
snd_seq_device
nfnetlink_queue
nfnetlink_log
nfnetlink
cmac
cpufreq_powersave
bnep
cpufreq_userspace
cpufreq_conservative
arc4
b43
mac80211
cfg80211
ssb
pcmcia
pcmcia_core
rng_core
dell_wmi
sparse_keymap
wmi_bmof
iTCO_wdt
iTCO_vendor_support
binfmt_misc
dell_laptop
dell_smbios
dell_wmi_descriptor
dcdbas
intel_rapl
x86_pkg_temp_thermal
intel_powerclamp
kvm_intel
kvm
irqbypass
intel_cstate
intel_uncore
intel_rapl_perf
joydev
serio_raw
pcspkr
btusb
btrtl
btbcm
btintel
bluetooth
evdev
drbg
ansi_cprng
ecdh_generic
sg
snd_hda_codec_hdmi
bcma
snd_hda_codec_idt
snd_hda_codec_generic
wmi
i915
snd_hda_intel
snd_hda_codec
dell_smo8800
snd_hda_core
dell_rbtn
snd_hwdep
video
snd_pcm_oss
rfkill
ac
battery
snd_mixer_oss
drm_kms_helper
drm
snd_pcm
mei_me
button
i2c_algo_bit
snd_timer
mei
shpchp
snd
soundcore
lpc_ich
ipt_MASQUERADE
nf_nat_masquerade_ipv4
iptable_nat
nf_nat_ipv4
nf_nat
xt_tcpudp
nf_conntrack_ipv4
nf_defrag_ipv4
xt_conntrack
nf_conntrack
crc32c_generic
iptable_filter
coretemp
dell_smm_hwmon
parport_pc
ppdev
lp
parport
nfsd
loop
auth_rpcgss
nfs_acl
lockd
grace
sunrpc
bbswitch(O)
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
fscrypto
btrfs
zstd_decompress
zstd_compress
xxhash
algif_skcipher
af_alg
dm_crypt
raid10
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
xor
raid6_pq
libcrc32c
raid1
raid0
multipath
linear
md_mod
dm_mirror
dm_region_hash
dm_log
dm_mod
sd_mod
hid_generic
usbhid
hid
crct10dif_pclmul
crc32_pclmul
crc32c_intel
ghash_clmulni_intel
pcbc
aesni_intel
aes_x86_64
crypto_simd
cryptd
glue_helper
psmouse
sdhci_pci
cqhci
ahci
libahci
sdhci
mmc_core
libata
ehci_pci
xhci_pci
ehci_hcd
xhci_hcd
i2c_i801
scsi_mod
thermal
e1000e
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM
Controller [8086:0154] (rev 09)
Subsystem: Dell 3rd Gen Core processor DRAM Controller [1028:0534]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: ivb_uncore
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core
processor PCI Express Root Port [8086:0151] (rev 09) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f5000000-f60fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core
processor Graphics Controller [8086:0166] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Dell 3rd Gen Core processor Graphics Controller [1028:0534]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f6400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Dell 7 Series/C210 Series Chipset Family USB xHCI Host
Controller [1028:0534]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 27
Region 0: Memory at f7e20000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C216
Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Dell 7 Series/C216 Chipset Family MEI Controller [1028:0534]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f7e3c000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network
Connection [8086:1502] (rev 04)
Subsystem: Dell 82579LM Gigabit Network Connection [1028:0534]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 26
Region 0: Memory at f7e00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7e39000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C216 Chipset Family
USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Dell 7 Series/C216 Chipset Family USB Enhanced Host
Controller [1028:0534]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7e38000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C216 Chipset Family
High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Dell 7 Series/C216 Chipset Family High Definition Audio
Controller [1028:0534]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 31
Region 0: Memory at f7e30000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C216 Chipset Family PCI
Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 2 [8086:1e12] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f7d00000-f7dfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 3 [8086:1e14] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Bus: primary=00, secondary=04, subordinate=07, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7200000-f7bfffff
Prefetchable memory behind bridge: 00000000f2b00000-00000000f34fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation 7 Series/C216 Chipset Family PCI
Express Root Port 4 [8086:1e16] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 19
Bus: primary=00, secondary=08, subordinate=0b, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f6800000-f71fffff
Prefetchable memory behind bridge: 00000000f2100000-00000000f2afffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.5 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 6 [8086:1e1a] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
Memory behind bridge: f7c00000-f7cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C216 Chipset Family
USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Dell 7 Series/C216 Chipset Family USB Enhanced Host
Controller [1028:0534]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f7e37000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge [0601]: Intel Corporation QM77 Express Chipset LPC
Controller [8086:1e55] (rev 04)
Subsystem: Dell QM77 Express Chipset LPC Controller [1028:0534]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family
6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Dell 7 Series Chipset Family 6-port SATA Controller [AHCI
mode] [1028:0534]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7e36000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C216 Chipset Family SMBus
Controller [8086:1e22] (rev 04)
Subsystem: Dell 7 Series/C216 Chipset Family SMBus Controller
[1028:0534]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7e35000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF108GLM [NVS
5200M] [10de:0dfc] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel modules: nouveau
03:00.0 Network controller [0280]: Broadcom Limited BCM43228 802.11a/b/g/n
[14e4:4359]
Subsystem: Dell BCM43228 802.11a/b/g/n [1028:0014]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: bcma-pci-bridge
Kernel modules: bcma
0c:00.0 SD Host controller [0805]: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
SD/MMC Card Reader Controller [1217:8221] (rev 05) (prog-if 01)
Subsystem: Dell OZ600FJ0/OZ900FJ0/OZ600FJS SD/MMC Card Reader
Controller [1028:0534]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f7c00000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci_pci
** USB devices:
Bus 002 Device 003: ID 413c:2513 Dell Computer Corp. internal USB Hub of E-Port
Replicator
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 413c:8197 Dell Computer Corp.
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 005: ID 046d:c063 Logitech, Inc. DELL Laser Mouse
Bus 003 Device 004: ID 04b3:301b IBM Corp. SK-8815 Keyboard
Bus 003 Device 003: ID 04b3:301a IBM Corp. 2-port low-power hub
Bus 003 Device 002: ID 413c:2513 Dell Computer Corp. internal USB Hub of E-Port
Replicator
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 9.5
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable-debug'), (500, 'stable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.17.0-0.bpo.1-amd64 (SMP w/4 CPU cores)
Locale: LANG=de_DE.utf8, LC_CTYPE=de_DE.utf8 (charmap=UTF-8),
LANGUAGE=de_DE.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.130
ii kmod 23-2
ii linux-base 4.5
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 recommends:
ii apparmor 2.11.0-3+deb9u2
ii firmware-linux-free 3.4
ii irqbalance 1.1.0-2.3
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 suggests:
ii debian-kernel-handbook 1.0.18
ii extlinux 3:6.03+dfsg-14.1+deb9u1
ii grub-pc 2.02~beta3-5
ii linux-doc-4.17 4.17.8-1~bpo9+1
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
ii firmware-brcm80211 20161130-3
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 20161130-3
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
--
Jorrit (Jö) Fahlke, Institute for Computational und Applied Mathematics,
University of Münster, Orleans-Ring 10, D-48149 Münster
Tel: +49 251 83 35146 Fax: +49 251 83 32729
Software is like sex; it's better when it's free.
-- Linus Torvalds
signature.asc
Description: PGP signature
