Package: src:linux
Version: 3.16.7-ckt20-1+deb8u3
Severity: normal
Dear Maintainer,
(I don't know, if this report may be a duplicate, the search on bdo is down and
i think this bug is important enough to file it anyway...)
on a fresh install of stable (jessie), the disk was completely filled up when I
just let the system sit for some days. Turned out the problem was in /var/log,
which is on / in this install (there is a helpful disk-full-analyze-tool in the
default install after all). I had to forcefully remove syslog, daemon.log,
kern.log and messsages and reboot the system to get it run again.
These files are still growing... After the reboot it the biggest entries in
/var/log are:
12:08:27 up 18 min, 3 users, load average: 3,81, 3,70, 2,69
-rw-r----- 1 root adm 34620838 Jan 31 11:56 messages.1
-rw-r----- 1 root adm 64654062 Jan 31 12:06 messages
-rw-r----- 1 root adm 67676079 Jan 31 11:56 daemon.log.1
-rw-r----- 1 root adm 70985143 Jan 31 11:56 kern.log.1
-rw-r----- 1 root adm 115802658 Jan 28 00:45 syslog.1
-rw-r----- 1 root adm 126748675 Jan 31 12:06 daemon.log
-rw-r----- 1 root adm 132827805 Jan 31 12:06 kern.log
-rw-r----- 1 root adm 398285263 Jan 31 12:06 syslog
The disk is not too small:
/dev/dm-1 110289760 5373368 99290948 6% /
(It grew from 5% to 6% in these 20 minutes).
The problem is this repeating message:
[ 1216.474108] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 1216.474111] iwl3945 0000:05:00.0: Falling back to user helper
[ 1216.474819] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 1216.475027] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 1216.475031] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 1216.475036] iwl3945 0000:05:00.0: Falling back to user helper
[ 1216.478257] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 1216.479653] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 1216.479660] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 1216.479663] iwl3945 0000:05:00.0: Falling back to user helper
[ 1216.480454] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 1216.480681] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 1216.480686] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 1216.480690] iwl3945 0000:05:00.0: Falling back to user helper
[ 1216.481272] iwl3945 0000:05:00.0: Could not read microcode: -12
I even installed firmware-linux-free, but this didn't help.
If the firmware is non-free, the kernel should be aware that this firmware
could be missing, and not spam the logs. I don't see a way to run a completely
free system on this hardware without disabling syslog. When I installed the
non-free firmware-iwlwifi the messages stopped, of course, but as you know you
have to actively include non-free ans find this package for that. Less
technical users would just have decided debian is not viable for them, I
suppose...
Thanks for your good work!
Ralf
-- Package-specific info:
** Version:
Linux version 3.16.0-4-amd64 (debian-ker...@lists.debian.org) (gcc version
4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt20-1+deb8u3 (2016-01-17)
** Command line:
BOOT_IMAGE=/vmlinuz-3.16.0-4-amd64 root=/dev/mapper/join--vg-root ro quiet
** Not tainted
** Kernel log:
[ 713.198066] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.198071] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.198074] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.199213] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.201978] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.201985] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.201988] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.202932] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.203164] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.203168] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.203171] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.203946] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.206692] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.206700] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.206703] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.207572] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.207804] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.207809] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.207812] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.209367] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.211396] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.211402] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.211405] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.211999] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.212267] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.212272] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.212274] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.213242] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.214843] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.214849] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.214852] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.215542] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.215755] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.215759] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.215762] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.216696] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.220355] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.220362] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.220364] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.221060] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.221649] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.221655] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.221658] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.222297] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.224538] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.224545] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.224548] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.226860] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.227123] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.227128] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.227130] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.228085] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.229395] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.229401] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.229404] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.230041] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.230379] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.230383] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.230386] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.230944] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.233248] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.233256] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.233259] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.233971] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.234219] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.234223] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.234226] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.234750] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.236267] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.236273] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.236276] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.236990] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.237194] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.237199] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.237202] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.238081] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.240730] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.240737] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.240742] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.241530] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.241749] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.241753] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.241755] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.242405] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.246094] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.246101] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.246104] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.246726] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.246984] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.246989] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.246992] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.247507] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.248872] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.248879] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.248883] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.249501] iwl3945 0000:05:00.0: Could not read microcode: -12
[ 713.249762] iwl3945 0000:05:00.0: firmware: failed to load
iwlwifi-3945-2.ucode (-2)
[ 713.249766] iwl3945 0000:05:00.0: Direct firmware load failed with error -2
[ 713.249769] iwl3945 0000:05:00.0: Falling back to user helper
[ 713.250359] iwl3945 0000:05:00.0: Could not read microcode: -12
** Model information
sys_vendor: FUJITSU SIEMENS
product_name: LIFEBOOK C1410
product_version:
chassis_vendor: FUJITSU SIEMENS
chassis_version: C1410
bios_vendor: FUJITSU // Phoenix Technologies Ltd.
bios_version: Version 1.09
board_vendor: FUJITSU
board_name: FJNB1BB
board_version: CP298000-04
** Loaded modules:
nls_utf8
squashfs
nls_cp437
vfat
fat
bnep
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
fscache
sunrpc
arc4
iwl3945
joydev
ecb
iwlegacy
btusb
iTCO_wdt
mac80211
bluetooth
6lowpan_iphc
iTCO_vendor_support
i915
coretemp
kvm
drm_kms_helper
cfg80211
snd_hda_codec_hdmi
drm
pcmcia
snd_hda_codec_realtek
pcspkr
psmouse
evdev
serio_raw
yenta_socket
pcmcia_rsrc
pcmcia_core
rfkill
snd_hda_codec_generic
irda
i2c_i801
crc_ccitt
i2c_algo_bit
lpc_ich
mfd_core
rng_core
shpchp
battery
snd_hda_intel
snd_hda_controller
snd_hda_codec
snd_hwdep
snd_pcm
snd_timer
snd
soundcore
i2c_core
tpm_infineon
tpm_tis
tpm
video
fujitsu_laptop
ac
button
acpi_cpufreq
processor
fuse
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
xts
gf128mul
algif_skcipher
af_alg
dm_crypt
dm_mod
usb_storage
sd_mod
crc_t10dif
crct10dif_generic
sg
sr_mod
cdrom
crct10dif_common
ata_generic
sdhci_pci
sdhci
mmc_core
ahci
ata_piix
libahci
firewire_ohci
firewire_core
crc_itu_t
libata
scsi_mod
ehci_pci
thermal
thermal_sys
uhci_hcd
ehci_hcd
sky2
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML
and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Fujitsu Limited. Device [10cf:1378]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS,
943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-if
00 [VGA controller])
Subsystem: Fujitsu Limited. Device [10cf:1381]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0300000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 1800 [size=8]
Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f0400000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME,
943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Fujitsu Limited. Device [10cf:1381]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0380000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition
Audio Controller [8086:27d8] (rev 02)
Subsystem: Fujitsu Limited. Device [10cf:1397]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f0640000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port
1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0000000-f00fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port
2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d0200000-d03fffff
Prefetchable memory behind bridge: 00000000d0400000-00000000d05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port
3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=07, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0600000-d08fffff
Prefetchable memory behind bridge: 00000000d0900000-00000000d0afffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Device [10cf:1389]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Device [10cf:1389]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Device [10cf:1389]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Device [10cf:1389]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI
Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Fujitsu Limited. Device [10cf:138a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0644000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=08, subordinate=0c, sec-latency=32
I/O behind bridge: 00005000-00005fff
Memory behind bridge: f0200000-f02fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge [8086:27b9] (rev 02)
Subsystem: Fujitsu Limited. Device [10cf:1384]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE
Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Fujitsu Limited. Device [10cf:1385]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at 1810 [size=16]
Kernel driver in use: ata_piix
00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7-M Family)
SATA Controller [AHCI mode] [8086:27c5] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Fujitsu Limited. Device [10cf:1387]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at 18d0 [size=8]
Region 1: I/O ports at 18c4 [size=4]
Region 2: I/O ports at 18c8 [size=8]
Region 3: I/O ports at 18c0 [size=4]
Region 4: I/O ports at 18b0 [size=16]
Region 5: Memory at f0644400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller
[8086:27da] (rev 02)
Subsystem: Fujitsu Limited. Device [10cf:1388]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18e0 [size=32]
Kernel driver in use: i801_smbus
02:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8055 PCI-E
Gigabit Ethernet Controller [11ab:4363] (rev 12)
Subsystem: Fujitsu Limited. Device [10cf:139a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 2000 [size=256]
[virtual] Expansion ROM at f0020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: sky2
05:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG
[Golan] Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation WM3945ABG MOW2 [8086:1001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at d0600000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: iwl3945
08:03.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b3)
Subsystem: Fujitsu Limited. Device [10cf:1254]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=08, secondary=09, subordinate=0c, sec-latency=176
Memory window 0: d8000000-dbffffff (prefetchable)
Memory window 1: dc000000-dfffffff
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Capabilities: <access denied>
Kernel driver in use: yenta_cardbus
08:03.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394 Controller
[1180:0552] (rev 08) (prog-if 10 [OHCI])
Subsystem: Fujitsu Limited. Device [10cf:1255]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f0200000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
08:03.2 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro
Host Adapter [1180:0822] (rev 17)
Subsystem: Fujitsu Limited. Device [10cf:1323]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin C routed to IRQ 16
Region 0: Memory at f0200800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
** USB devices:
Bus 005 Device 002: ID 8564:1000
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 0c24:000f Taiyo Yuden Bluetooth Device (V2.0+EDR)
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 8.3
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.16.0-4-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-3.16.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 18-3
ii linux-base 3.5
Versions of packages linux-image-3.16.0-4-amd64 recommends:
ii firmware-linux-free 3.3
pn irqbalance <none>
Versions of packages linux-image-3.16.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22+deb8u1
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16.0-4-amd64/postinst/mips-initrd-3.16.0-4-amd64:
linux-image-3.16.0-4-amd64/prerm/removing-running-kernel-3.16.0-4-amd64: true
linux-image-3.16.0-4-amd64/postinst/depmod-error-initrd-3.16.0-4-amd64: false
