Package: src:linux
Version: 4.1.6-1
Severity: normal
Dear maintainer(s),
I recently put one of my file systems on LVM RAID1. All is fine when I
lvconvert or lvcreate the RAID1 mirror on a running kernel. The problem
is when I reboot the system. The linux-image-4.1.0-1-amd64 is affected
by the same problem. Rebooting with a linux-image-4.0.0-2-amd64 kernel
works fine. The LVM RAID1 file system mounts automatically and is fully
usable.
During the linux-image-4.1.0-*-amd64 boots I see:
Setting up LVM Volume Groups... lvmetad is not active yet, using direct
activation during sysinit
device-mapper: reload ioctl on (253:8) failed: Invalid argument
and a little later:
fsck.ext4: No such file or directory while trying to open
/dev/mapper/helix-srv
Possibly non-existent device?
Trying to activate the LV after the boot does not work either.
# lvchange -ay helix/srv
device-mapper: reload iocth on (253:8) failed: Invalid argument
In my syslog I see:
mdX: invalid bitmap file superblock: bad magic
mdX: bitmap file superblock
magic: 00000401
and
mdX: failed to create bitmap (-22)
device-mapper: table: 253:8 raid: Fail to run raid araay
I have found https://bugzilla.kernel.org/show_bug.cgi?id=100491[1] which
mentions some of the messages I observe. I do not get the OOPS but it
might be related.
For the time being I'll stick to 4.0.
-- Package-specific info:
** Version:
Linux version 4.1.0-2-amd64 (debian-ker...@lists.debian.org) (gcc version 4.9.3
(Debian 4.9.3-3) ) #1 SMP Debian 4.1.6-1 (2015-08-23)
** Command line:
BOOT_IMAGE=/vmlinuz-4.1.0-2-amd64 root=/dev/mapper/helix-root ro quiet
cgroup_enable=memory
** Tainted: I (2048)
* Working around severe firmware bug.
** Kernel log:
[ 5.923596] nouveau [ VBIOS][0000:0f:00.0] version 70.18.89.00.02
[ 5.924005] nouveau [ PMC][0000:0f:00.0] MSI interrupts enabled
[ 5.924042] nouveau [ PFB][0000:0f:00.0] RAM type: DDR3
[ 5.924044] nouveau [ PFB][0000:0f:00.0] RAM size: 512 MiB
[ 5.924045] nouveau [ PFB][0000:0f:00.0] ZCOMP: 960 tags
[ 5.927663] nouveau [ VOLT][0000:0f:00.0] GPU voltage: 900000uv
[ 5.948974] input: HP WMI hotkeys as /devices/virtual/input/input14
[ 5.955823] nouveau [ PTHERM][0000:0f:00.0] FAN control: none / external
[ 5.955832] nouveau [ PTHERM][0000:0f:00.0] fan management: automatic
[ 5.955836] nouveau [ PTHERM][0000:0f:00.0] internal sensor: yes
[ 5.975835] nouveau [ CLK][0000:0f:00.0] 03: core 135 MHz shader 270
MHz memory 135 MHz
[ 5.975844] nouveau [ CLK][0000:0f:00.0] 07: core 405 MHz shader 810
MHz memory 405 MHz
[ 5.975851] nouveau [ CLK][0000:0f:00.0] 0f: core 520 MHz shader 1230
MHz memory 790 MHz
[ 5.975880] nouveau [ CLK][0000:0f:00.0] --: core 405 MHz shader 810
MHz memory 405 MHz
[ 5.976327] [TTM] Zone kernel: Available graphics memory: 12336452 kiB
[ 5.976331] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 5.976334] [TTM] Initializing pool allocator
[ 5.976344] [TTM] Initializing DMA pool allocator
[ 5.976364] nouveau [ DRM] VRAM: 512 MiB
[ 5.976367] nouveau [ DRM] GART: 1048576 MiB
[ 5.976372] nouveau [ DRM] TMDS table version 2.0
[ 5.976375] nouveau [ DRM] DCB version 4.0
[ 5.976379] nouveau [ DRM] DCB outp 00: 02000360 00000000
[ 5.976382] nouveau [ DRM] DCB outp 01: 02000362 00020010
[ 5.976385] nouveau [ DRM] DCB outp 02: 028003a6 0f220010
[ 5.976388] nouveau [ DRM] DCB outp 03: 01011380 00000000
[ 5.976391] nouveau [ DRM] DCB outp 04: 08011382 00020010
[ 5.976394] nouveau [ DRM] DCB outp 05: 088113c6 0f220010
[ 5.976398] nouveau [ DRM] DCB conn 00: 00101064
[ 5.976401] nouveau [ DRM] DCB conn 01: 00202165
[ 6.026092] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 6.026094] [drm] Driver supports precise vblank timestamp query.
[ 6.043502] input: HDA NVidia HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input12
[ 6.043623] input: HDA NVidia HDMI/DP,pcm=7 as
/devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input13
[ 6.043731] input: HDA NVidia HDMI/DP,pcm=8 as
/devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input15
[ 6.043798] input: HDA NVidia HDMI/DP,pcm=9 as
/devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input16
[ 6.078586] nouveau [ DRM] MM: using COPY for buffer copies
[ 6.097627] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly.
Using workaround
[ 6.186606] nouveau [ DRM] allocated 1600x900 fb: 0x70000, bo
ffff88060311cc00
[ 6.186838] fbcon: nouveaufb (fb0) is primary device
[ 6.333908] Console: switching to colour frame buffer device 200x56
[ 6.336132] nouveau 0000:0f:00.0: fb0: nouveaufb frame buffer device
[ 6.336135] nouveau 0000:0f:00.0: registered panic notifier
[ 6.406247] [drm] Initialized nouveau 1.2.2 20120801 for 0000:0f:00.0 on
minor 0
[ 7.649017] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 7.791926] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 8.294446] loop: module loaded
[ 8.586592] raid6: sse2x1 gen() 4194 MB/s
[ 8.654630] raid6: sse2x1 xor() 3259 MB/s
[ 8.722647] raid6: sse2x2 gen() 4922 MB/s
[ 8.790666] raid6: sse2x2 xor() 3789 MB/s
[ 8.858674] raid6: sse2x4 gen() 5469 MB/s
[ 8.926690] raid6: sse2x4 xor() 4164 MB/s
[ 8.926692] raid6: using algorithm sse2x4 gen() 5469 MB/s
[ 8.926694] raid6: .... xor() 4164 MB/s, rmw enabled
[ 8.926695] raid6: using ssse3x2 recovery algorithm
[ 8.944629] async_tx: api initialized (async)
[ 8.948379] xor: measuring software checksum speed
[ 8.986702] prefetch64-sse: 6642.000 MB/sec
[ 9.026712] generic_sse: 5770.000 MB/sec
[ 9.026714] xor: using function: prefetch64-sse (6642.000 MB/sec)
[ 9.053530] md: raid6 personality registered for level 6
[ 9.053533] md: raid5 personality registered for level 5
[ 9.053535] md: raid4 personality registered for level 4
[ 9.065278] device-mapper: raid: Loading target version 1.6.0
[ 9.094853] md: raid1 personality registered for level 1
[ 9.096358] md/raid1:mdX: active with 2 out of 2 mirrors
[ 9.096675] mdX: invalid bitmap file superblock: bad magic
[ 9.096680] mdX: bitmap file superblock:
[ 9.096682] magic: 00000401
[ 9.096684] version: 1041
[ 9.096687] uuid: 00000421.1ff55bd9.00040002.00000000
[ 9.096689] events: 592
[ 9.096690] events cleared: 592
[ 9.096692] state: 00000000
[ 9.096694] chunksize: 524288 B
[ 9.096695] daemon sleep: 5s
[ 9.096697] sync size: 262144000 KB
[ 9.096699] max write behind: 0
[ 9.096703] mdX: failed to create bitmap (-22)
[ 9.096808] device-mapper: table: 253:8: raid: Fail to run raid array
[ 9.096824] device-mapper: ioctl: error adding target to table
[ 9.192429] Adding 26214396k swap on /dev/mapper/helix-swap. Priority:-1
extents:1 across:26214396k FS
[ 22.307449] EXT4-fs (sdb1): mounting ext2 file system using the ext4
subsystem
[ 22.310554] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 22.336806] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts:
(null)
[ 22.349134] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts:
(null)
[ 22.776576] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 22.809495] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 22.929623] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[ 23.338263] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 24.579899] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.957043] tg3 0000:01:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 24.957049] tg3 0000:01:00.0 eth0: Flow control is off for TX and off for RX
[ 24.957067] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 26.233928] tg3 0000:1c:00.0 eth1: Link is up at 100 Mbps, full duplex
[ 26.233934] tg3 0000:1c:00.0 eth1: Flow control is off for TX and off for RX
[ 26.233951] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 49.915484] bridge: automatic filtering via arp/ip/ip6tables has been
deprecated. Update your scripts to load br_netfilter if you need this.
[ 49.940068] Bridge firewalling registered
** Model information
sys_vendor: Hewlett-Packard
product_name: HP Z600 Workstation
product_version:
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: 786G4 v03.54
board_vendor: Hewlett-Packard
board_name: 0B54h
board_version: D
** Loaded modules:
ipt_MASQUERADE
nf_nat_masquerade_ipv4
xt_addrtype
br_netfilter
bridge
stp
llc
overlay
xt_REDIRECT
nf_nat_redirect
iptable_nat
nf_nat_ipv4
nf_nat
xt_tcpudp
xt_mac
nf_conntrack_ipv4
nf_defrag_ipv4
nf_conntrack_ipv6
nf_defrag_ipv6
xt_conntrack
nf_conntrack
iptable_filter
ip_tables
ip6table_filter
ip6_tables
x_tables
raid1
dm_raid
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
xor
async_tx
raid6_pq
loop
intel_powerclamp
coretemp
kvm_intel
kvm
hp_wmi
sparse_keymap
rfkill
nouveau
snd_hda_codec_hdmi
crct10dif_pclmul
crc32_pclmul
ghash_clmulni_intel
mxm_wmi
video
ttm
drm_kms_helper
drm
aesni_intel
ppdev
iTCO_wdt
iTCO_vendor_support
evdev
lpc_ich
psmouse
aes_x86_64
i2c_algo_bit
serio_raw
lrw
gf128mul
mfd_core
glue_helper
snd_hda_codec_realtek
ablk_helper
cryptd
sg
wmi
snd_hda_codec_generic
parport_pc
button
snd_hda_intel
snd_hda_controller
snd_hda_codec
snd_hda_core
8250_fintek
snd_hwdep
snd_pcm
snd_timer
parport
snd
soundcore
acpi_cpufreq
processor
i7core_edac
thermal_sys
edac_core
shpchp
ext4
crc16
mbcache
jbd2
dm_mod
md_mod
hid_generic
usbhid
hid
sr_mod
cdrom
sd_mod
crc32c_intel
ahci
libahci
libata
firewire_ohci
firewire_core
crc_itu_t
scsi_mod
tg3
xhci_pci
ehci_pci
uhci_hcd
ptp
xhci_hcd
ehci_hcd
pps_core
libphy
usbcore
usb_common
floppy
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5520 I/O Hub to ESI Port
[8086:3406] (rev 13)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: fd000000-fd0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0f, subordinate=0f, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fa000000-fb0fffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f9ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=28, subordinate=28, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:10.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 Physical and Link
Layer Registers Port 0 [8086:3425] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:10.1 PIC [0800]: Intel Corporation 7500/5520/5500/X58 Routing and Protocol
Layer Registers Port 0 [8086:3426] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:11.0 PIC [0800]: Intel Corporation 7500/5520/5500 Physical and Link Layer
Registers Port 1 [8086:3427] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:11.1 PIC [0800]: Intel Corporation 7500/5520/5500 Routing & Protocol Layer
Register Port 1 [8086:3428] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:14.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub System
Management Registers [8086:342e] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: i7core_edac
00:14.1 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub GPIO and
Scratch Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.2 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub Control Status
and RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:15.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 Trusted Execution
Technology Registers [8086:342f] (rev 13) (prog-if 20 [IO(X)-APIC])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #4 [8086:3a37] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at d000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #5 [8086:3a38] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d020 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at d040 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #2 [8086:3a3c] (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ee004800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 82801JI (ICH10 Family) HD Audio
Controller [8086:3a3e]
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 36
Region 0: Memory at ee000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 1 [8086:3a40] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Bus: primary=00, secondary=1c, subordinate=1c, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: ef000000-ef0fffff
Prefetchable memory behind bridge: 00000000ed100000-00000000ed2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 6 [8086:3a4a] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 25
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: fc000000-fc0fffff
Prefetchable memory behind bridge: 00000000ed300000-00000000ed4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at d060 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at d0a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at ee004c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
90) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=37, subordinate=37, sec-latency=32
Memory behind bridge: ed000000-ed0fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIR (ICH10R) LPC Interface
Controller [8086:3a16]
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 RAID bus controller [0104]: Intel Corporation SATA Controller [RAID
mode] [8086:2822]
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 35
Region 0: I/O ports at d100 [size=8]
Region 1: I/O ports at d110 [size=4]
Region 2: I/O ports at d108 [size=8]
Region 3: I/O ports at d114 [size=4]
Region 4: I/O ports at d0c0 [size=32]
Region 5: Memory at ee004000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
01:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5764M
Gigabit Ethernet PCIe [14e4:1684] (rev 10)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at fc000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
03:00.0 USB controller [0c03]: Texas Instruments TUSB73x0 SuperSpeed USB 3.0
xHCI Host Controller [104c:8241] (rev 02) (prog-if 30 [XHCI])
Subsystem: Device [1b5b:8040]
Physical Slot: 1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 26
Region 0: Memory at fd000000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fd010000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
0f:00.0 VGA compatible controller [0300]: NVIDIA Corporation GT218 [NVS 300]
[10de:10d8] (rev a2) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:0862]
Physical Slot: 2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 39
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f4000000 (64-bit, prefetchable) [size=64M]
Region 3: Memory at f8000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at e000 [size=128]
[virtual] Expansion ROM at fb080000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nouveau
0f:00.1 Audio device [0403]: NVIDIA Corporation High Definition Audio
Controller [10de:0be3] (rev a1)
Subsystem: Hewlett-Packard Company Device [103c:0862]
Physical Slot: 2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 37
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
1c:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5761
Gigabit Ethernet PCIe [14e4:1681] (rev 10)
Subsystem: Broadcom Corporation NetXtreme BCM5761 Gigabit Ethernet PCIe
[14e4:1681]
Physical Slot: 3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at ef000000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at ef010000 (64-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at ef020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: tg3
37:05.0 FireWire (IEEE 1394) [0c00]: LSI Corporation FW322/323 [TrueFire] 1394a
Controller [11c1:5811] (rev 70) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
3e:00.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath
Architecture Generic Non-core Registers [8086:2c70] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:00.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath
Architecture System Address Decoder [8086:2d81] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:02.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 0
[8086:2d90] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:02.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 0
[8086:2d91] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:02.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link
0 [8086:2d92] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:02.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link
1 [8086:2d93] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:02.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 1
[8086:2d94] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:02.5 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 1
[8086:2d95] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:03.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Registers [8086:2d98] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:03.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Target Address Decoder [8086:2d99] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:03.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller RAS Registers [8086:2d9a] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:03.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Test Registers [8086:2d9c] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:04.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Control [8086:2da0] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:04.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Address [8086:2da1] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:04.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Rank [8086:2da2] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:04.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Thermal Control [8086:2da3] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:05.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Control [8086:2da8] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:05.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Address [8086:2da9] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:05.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Rank [8086:2daa] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:05.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Thermal Control [8086:2dab] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:06.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Control [8086:2db0] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:06.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Address [8086:2db1] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:06.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Rank [8086:2db2] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3e:06.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Thermal Control [8086:2db3] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:00.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath
Architecture Generic Non-core Registers [8086:2c70] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:00.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath
Architecture System Address Decoder [8086:2d81] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:02.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 0
[8086:2d90] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:02.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 0
[8086:2d91] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:02.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link
0 [8086:2d92] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:02.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link
1 [8086:2d93] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:02.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 1
[8086:2d94] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:02.5 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 1
[8086:2d95] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:03.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Registers [8086:2d98] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:03.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Target Address Decoder [8086:2d99] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:03.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller RAS Registers [8086:2d9a] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:03.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Test Registers [8086:2d9c] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Control [8086:2da0] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Address [8086:2da1] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Rank [8086:2da2] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Thermal Control [8086:2da3] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Control [8086:2da8] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Address [8086:2da9] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Rank [8086:2daa] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Thermal Control [8086:2dab] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:06.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Control [8086:2db0] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:06.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Address [8086:2db1] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:06.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Rank [8086:2db2] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:06.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Thermal Control [8086:2db3] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:130a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
** USB devices:
Bus 010 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 002: ID 046d:c078 Logitech, Inc.
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: stretch/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'testing-updates'), (500,
'stable-updates'), (500, 'unstable'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 4.1.0-2-amd64 (SMP w/8 CPU cores)
Locale: LANG=ja_JP.UTF-8, LC_CTYPE=ja_JP.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: sysvinit (via /sbin/init)
Versions of packages linux-image-4.1.0-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.57
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 21-1
ii linux-base 4.0
Versions of packages linux-image-4.1.0-2-amd64 recommends:
pn firmware-linux-free <none>
pn irqbalance <none>
Versions of packages linux-image-4.1.0-2-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-28
pn linux-doc-4.1 <none>
Versions of packages linux-image-4.1.0-2-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-4.1.0-2-amd64/postinst/depmod-error-initrd-4.1.0-2-amd64: false
linux-image-4.1.0-2-amd64/postinst/mips-initrd-4.1.0-2-amd64:
linux-image-4.1.0-2-amd64/prerm/removing-running-kernel-4.1.0-2-amd64: true
Hope this helps,
--
Olaf Meeuwissen, LPIC-2 EPSON FLOSS Engineer -- AVASYS CORPORATION
FSF Associate Member #1962 Help support software freedom
http://www.fsf.org/jf?referrer=1962[2]
