Package: src:linux
Version: 3.16.7-ckt7-1
Severity: important
Dear Maintainer,
I have an old Dell (Dimension XPS B766r) which was previously running Debian 6
on it serving as a fileserver with 8 sata HDDs, 2 IDE HDDs, and an SD to IDE
adapter running the OS. It has two PCI RAID cards running in jBOD to facilitate
the numerous drives. The MegaRAID PCI card is detected and it's drives all
show up. The Silicon Image SiI 3114 RAID card is detected but has a conflict
with the IRQ for the floppy drive (which is disabled in BIOS). The Silicon
Image card detects all drives, and the kernel detects the card and loads the
sata_sil module for it, but once the OS is booted none of the drives appear.
As a workaround, in rc.local I have the following for the time being:
# rc.local
rmmod sata_sil
modprobe -v sata_sil
mount /opt/mnt/driveA
mount /opt/mnt/driveB
mount /opt/mnt/driveC
mount /opt/mnt/driveD
I have fstab entries for these mounts setup with the noauto option so the
system doesn't fail on boot.
lsmod shows the sata_sil module in the system modules after boot but it seems
to not recognize the card and/or the drives attached to it.
-- Package-specific info:
** Version:
Linux version 3.16.0-4-686-pae (debian-ker...@lists.debian.org) (gcc version
4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt7-1 (2015-03-01)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-686-pae
root=UUID=35edd3a8-224b-4aba-a58e-85c4e341d54d ro quiet
init=/lib/systemd/systemd
** Not tainted
** Kernel log:
[ 5.348426] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
(null)
[ 6.569549] systemd[1]: Cannot add dependency job for unit
display-manager.service, ignoring: Unit display-manager.service failed to load:
No such file or directory.
[ 6.914491] fuse init (API version 7.23)
[ 7.419642] systemd-udevd[151]: starting version 215
[ 7.992617] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 7.992642] ACPI: Power Button [PWRF]
[ 8.239366] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 8.246524] intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 8.334653] MPU-401 device not found or device busy
[ 8.670179] [drm] Initialized drm 1.1.0 20060810
[ 8.853367] wmi: Mapper loaded
[ 9.087456] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 9.315527] dcdbas dcdbas: Dell Systems Management Base Driver (version
5.6.0-3.2)
[ 9.325094] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 9.325111] PCI: setting IRQ 11 as level-triggered
[ 9.332493] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x20154000
[ 9.332512] nouveau [ DEVICE][0000:01:00.0] Chipset: NV05 (NV05)
[ 9.332520] nouveau [ DEVICE][0000:01:00.0] Family : NV04
[ 9.332798] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 9.353128] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 9.353141] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 9.353152] nouveau [ VBIOS][0000:01:00.0] BMP version 2.1
[ 9.353538] nouveau [ VBIOS][0000:01:00.0] version 02.05.13.03.00
[ 9.414468] nouveau W[ VBIOS][0000:01:00.0] DCB table not found
[ 9.414871] nouveau W[ VBIOS][0000:01:00.0] DCB table not found
[ 9.415015] nouveau W[ VBIOS][0000:01:00.0] DCB table not found
[ 9.415026] nouveau W[ VBIOS][0000:01:00.0] DCB table not found
[ 9.415114] nouveau W[ PTIMER][0000:01:00.0] unknown input clock freq
[ 9.415134] nouveau [ PFB][0000:01:00.0] RAM type: SDRAM
[ 9.415143] nouveau [ PFB][0000:01:00.0] RAM size: 32 MiB
[ 9.415151] nouveau [ PFB][0000:01:00.0] ZCOMP: 0 tags
[ 9.442538] nouveau [ CLK][0000:01:00.0] --:
[ 9.442586] nouveau W[ VBIOS][0000:01:00.0] DCB table not found
[ 9.442645] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[ 9.442674] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[ 9.442703] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
[ 9.449890] [TTM] Zone kernel: Available graphics memory: 255938 kiB
[ 9.449905] [TTM] Initializing pool allocator
[ 9.449941] [TTM] Initializing DMA pool allocator
[ 9.450421] nouveau [ DRM] VRAM: 31 MiB
[ 9.450437] nouveau [ DRM] GART: 64 MiB
[ 9.450449] nouveau [ DRM] BMP version 2.1
[ 9.450459] nouveau W[ DRM] No DCB data found in VBIOS
[ 9.475999] nouveau [ DRM] Saving VGA fonts
[ 9.532472] nouveau W[ DRM] No DCB data found in VBIOS
[ 9.533239] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 9.533248] [drm] Driver supports precise vblank timestamp query.
[ 9.598779] nouveau [ DRM] MM: using M2MF for buffer copies
[ 9.668823] nouveau [ DRM] allocated 1280x1024 fb: 0x4000, bo ddb58000
[ 9.669122] fbcon: nouveaufb (fb0) is primary device
[ 9.976583] Console: switching to colour frame buffer device 160x64
[ 9.979031] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 9.979042] nouveau 0000:01:00.0: registered panic notifier
[ 9.979063] [drm] Initialized nouveau 1.1.2 20120801 for 0000:01:00.0 on
minor 0
[ 10.548821] iTCO_vendor_support: vendor-support=0
[ 10.553523] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 10.553615] iTCO_wdt: Found a ICH TCO device (Version=1, TCOBASE=0x0460)
[ 10.555947] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.617917] ppdev: user-space parallel port driver
[ 10.648010] Adding 367612k swap on /dev/sdc5. Priority:-1 extents:1
across:367612k FS
[ 11.176137] floppy0: no floppy controllers found
[ 11.176167] work still pending
[ 14.208135] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro
[ 14.280153] EXT4-fs (sda1): mounting ext3 file system using the ext4
subsystem
[ 14.282099] EXT4-fs (sdb1): mounting ext3 file system using the ext4
subsystem
[ 14.332128] EXT4-fs (sde1): mounted filesystem with ordered data mode. Opts:
(null)
[ 14.346588] EXT4-fs (sdb1): warning: maximal mount count reached, running
e2fsck is recommended
[ 14.348965] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts:
(null)
[ 14.376447] EXT4-fs (sda1): warning: maximal mount count reached, running
e2fsck is recommended
[ 14.380856] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
(null)
[ 14.549008] systemd-journald[131]: Received request to flush runtime journal
from PID 1
[ 15.468661] r8169 0000:02:0c.0 eth0: link down
[ 15.468692] r8169 0000:02:0c.0 eth0: link down
[ 15.468783] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.073603] RPC: Registered named UNIX socket transport module.
[ 16.073622] RPC: Registered udp transport module.
[ 16.073628] RPC: Registered tcp transport module.
[ 16.073634] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.092308] FS-Cache: Loaded
[ 16.141874] FS-Cache: Netfs 'nfs' registered for caching
[ 16.195933] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 16.631011] Fusion MPT base driver 3.04.20
[ 16.631029] Copyright (c) 1999-2008 LSI Corporation
[ 16.902128] Fusion MPT misc device (ioctl) driver 3.04.20
[ 16.903643] mptctl: Registered with Fusion MPT base driver
[ 16.903660] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 17.236259] Bluetooth: Core ver 2.19
[ 17.236384] NET: Registered protocol family 31
[ 17.236392] Bluetooth: HCI device and connection manager initialized
[ 17.237170] Bluetooth: HCI socket layer initialized
[ 17.237189] Bluetooth: L2CAP socket layer initialized
[ 17.237227] Bluetooth: SCO socket layer initialized
[ 17.319244] Netfilter messages via NETLINK v0.30.
[ 17.707132] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
[ 17.707192] NFSD: starting 90-second grace period (net c164fcc0)
[ 18.537507] r8169 0000:02:0c.0 eth0: link up
[ 18.537545] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
** Model information
not available
** Loaded modules:
nfnetlink_queue
nfnetlink_log
nfnetlink
bluetooth
6lowpan_iphc
rfkill
mptctl
mptbase
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
fscache
sunrpc
ppdev
iTCO_wdt
iTCO_vendor_support
dcdbas
nouveau
pcspkr
evdev
psmouse
serio_raw
mxm_wmi
i2c_i801
wmi
video
snd_wavefront
ttm
drm_kms_helper
snd_cs4236
snd_opl3_lib
snd_hwdep
drm
snd_wss_lib
i2c_algo_bit
snd_pcm
i2c_core
parport_pc
parport
snd_timer
snd_mpu401_uart
snd_rawmidi
snd_seq_device
lpc_ich
snd
soundcore
ns558
mfd_core
rng_core
gameport
shpchp
processor
thermal_sys
button
fuse
autofs4
ext4
crc16
mbcache
jbd2
dm_mod
sg
sd_mod
crc_t10dif
crct10dif_generic
crct10dif_common
ata_generic
ata_piix
uhci_hcd
ehci_hcd
libata
megaraid_mbox
megaraid_mm
usbcore
usb_common
r8169
mii
scsi_mod
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet static
address 172.16.0.3
netmask 255.255.0.0
network 172.16.0.1
broadcast 172.16.255.255
gateway 172.16.0.1
dns-nameservers 172.16.0.1
dns-search yggdrasil
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP
group default qlen 1000
link/ether 94:0c:6d:80:86:f3 brd ff:ff:ff:ff:ff:ff
inet 172.16.0.3/16 brd 172.16.255.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::960c:6dff:fe80:86f3/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 800 12 0 0 0 0 0 0 800
12 0 0 0 0 0 0
eth0: 2477355 1871 0 7 0 0 0 0 130051
1072 0 0 0 0 0 0
*** Protocol statistics:
Ip:
1821 total packets received
0 forwarded
0 incoming packets discarded
1821 incoming packets delivered
1073 requests sent out
32 dropped because of missing route
Icmp:
3 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 3
3 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 3
IcmpMsg:
InType3: 3
OutType3: 3
Tcp:
8 active connections openings
0 passive connection openings
4 failed connection attempts
1 connection resets received
0 connections established
1687 segments received
943 segments send out
1 segments retransmited
0 bad segments received.
5 resets sent
Udp:
173 packets received
1 packets to unknown port received.
0 packet receive errors
130 packets sent
UdpLite:
TcpExt:
14 delayed acks sent
1614 packet headers predicted
36 acknowledgments not containing data payload received
10 predicted acknowledgments
1 times recovered from packet loss by selective acknowledgements
1 fast retransmits
1 connections reset due to early user close
TCPSackShiftFallback: 16
TCPRcvCoalesce: 20
TCPOrigDataSent: 45
IpExt:
InMcastPkts: 7
InBcastPkts: 47
OutBcastPkts: 47
InOctets: 2452903
OutOctets: 115133
InMcastOctets: 224
InBcastOctets: 6460
OutBcastOctets: 6460
InNoECTPkts: 1822
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82820 820 (Camino) Chipset Host
Bridge (MCH) [8086:2501] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 82820 820 (Camino) Chipset AGP
Bridge [8086:250f] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: fc800000-fe8fffff
Prefetchable memory behind bridge: f0500000-f45fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1e.0 PCI bridge [0604]: Intel Corporation 82801AA PCI Bridge [8086:2418]
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe900000-feafffff
Prefetchable memory behind bridge: f4600000-f46fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801AA ISA Bridge (LPC)
[8086:2410] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel driver in use: lpc_ich
00:1f.1 IDE interface [0101]: Intel Corporation 82801AA IDE Controller
[8086:2411] (rev 02) (prog-if 80 [Master])
Subsystem: Intel Corporation 82801AA IDE Controller [8086:2411]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: ata_piix
00:1f.2 USB controller [0c03]: Intel Corporation 82801AA USB Controller
[8086:2412] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801AA USB Controller [8086:2412]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at ef80 [size=32]
Kernel driver in use: uhci_hcd
00:1f.3 SMBus [0c05]: Intel Corporation 82801AA SMBus Controller [8086:2413]
(rev 02)
Subsystem: Intel Corporation 82801AA SMBus Controller [8086:2413]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 6
Region 4: I/O ports at efa0 [size=16]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation NV5 [Riva TNT2
Model 64 / Model 64 Pro] [10de:002d] (rev 15) (prog-if 00 [VGA controller])
Subsystem: NVIDIA Corporation Device [10de:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f2000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at fe8f0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW-
Rate=x4
Kernel driver in use: nouveau
02:09.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3114
[SATALink/SATARaid] Serial ATA Controller [1095:3114] (rev 02)
Subsystem: Silicon Image, Inc. Device [1095:7114]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 6
Region 0: I/O ports at dff0 [size=8]
Region 1: I/O ports at dfe4 [size=4]
Region 2: I/O ports at dfa8 [size=8]
Region 3: I/O ports at dfe0 [size=4]
Region 4: I/O ports at df90 [size=16]
Region 5: Memory at feaffc00 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at fea00000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
02:0a.0 RAID bus controller [0104]: LSI Logic / Symbios Logic MegaRAID
[1000:1960] (rev 01)
Subsystem: LSI Logic / Symbios Logic MegaRAID SATA 150-4 RAID
Controller [1000:4523]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f46f0000 (32-bit, prefetchable) [size=64K]
Expansion ROM at feae0000 [disabled] [size=64K]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: megaraid
02:0c.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8169 PCI
Gigabit Ethernet Controller [10ec:8169] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8169/8110 Family PCI
Gigabit Ethernet NIC [10ec:8169]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at feaff800 (32-bit, non-prefetchable) [size=256]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: r8169
** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 8.0
APT prefers testing-updates
APT policy: (500, 'testing-updates'), (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.16.0-4-686-pae (SMP w/1 CPU core)
Locale: LANG=en_CA.UTF-8, LC_CTYPE=en_CA.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: sysvinit (via /sbin/init)
Versions of packages linux-image-3.16.0-4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.55
ii initramfs-tools [linux-initramfs-tool] 0.116
ii kmod 18-3
ii linux-base 3.5
ii module-init-tools 18-3
Versions of packages linux-image-3.16.0-4-686-pae recommends:
ii firmware-linux-free 3.3
pn irqbalance <none>
ii libc6-i686 2.19-15
Versions of packages linux-image-3.16.0-4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-21
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf-show failed
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
