Package: src:linux
Version: 3.16.2-2
Severity: critical
Justification: breaks the whole system
I've got a debian unstable system running in a ganeti/kvm vm that runs
with lvm. The physical volume the root file system resides on is
encrypted with luks. I've installed dropbear to unlock the luks volume
via ssh, using a kernel cmdline ip=... in /etc/grub/default
Up and including linux-image-3.14-2-amd64 this worked flawlessly.
However, having installed and booted from 3.16-1, the kernel panics
after unlocking the luks volume. There were some error messages about
/dev/pts and/or /dev not being mounted successfully, but as the kernel
panicked, the busybox console (accessed via spice) was frozen and I had to ask
the admin
admin to hard-reset the machine for me.
The 3.14-2 kernel continues to boot normally,
I'm a bit at loss what might cause 3.16 to panic but 3.14 to boot
successfully. Unfortunately I cannot hard-reset the machine myself
(spice remote-viewer does not to support hard-reset signals to the vm)
and I wasn't able to deduce anything from the few kernel panic lines
on the console.
With the best regards, and a lot of thanks for this great operating
system,
C. Dominik Bódi
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: Bochs
product_name: Bochs
product_version:
chassis_vendor: Bochs
chassis_version:
bios_vendor: Bochs
bios_version: Bochs
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma]
[8086:1237] (rev 02)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton
II] [8086:7000]
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.1 IDE interface [0101]: Intel Corporation 82371SB PIIX3 IDE
[Natoma/Triton II] [8086:7010] (prog-if 80 [Master])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at c120 [size=16]
Kernel driver in use: ata_piix
00:01.2 USB controller [0c03]: Intel Corporation 82371SB PIIX3 USB
[Natoma/Triton II] [8086:7020] (rev 01) (prog-if 00 [UHCI])
Subsystem: Red Hat, Inc QEMU Virtual Machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at c080 [size=32]
Kernel driver in use: uhci_hcd
00:01.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113]
(rev 03)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Kernel driver in use: piix4_smbus
00:02.0 VGA compatible controller [0300]: Red Hat, Inc. QXL paravirtual graphic
card [1b36:0100] (rev 03) (prog-if 00 [VGA controller])
Subsystem: Red Hat, Inc QEMU Virtual Machine [1af4:1100]
Physical Slot: 2
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=64M]
Region 1: Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
Region 2: Memory at fc020000 (32-bit, non-prefetchable) [size=8K]
Region 3: I/O ports at c0a0 [size=32]
Expansion ROM at fc000000 [disabled] [size=64K]
00:03.0 Unclassified device [00ff]: Red Hat, Inc Virtio memory balloon
[1af4:1002]
Subsystem: Red Hat, Inc Device [1af4:0005]
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c0c0 [size=32]
Kernel driver in use: virtio-pci
00:04.0 Communication controller [0780]: Red Hat, Inc Virtio console [1af4:1003]
Subsystem: Red Hat, Inc Device [1af4:0003]
Physical Slot: 4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at c0e0 [size=32]
Region 1: Memory at fc022000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] MSI-X: Enable+ Count=32 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Kernel driver in use: virtio-pci
00:05.0 SCSI storage controller [0100]: Red Hat, Inc Virtio block device
[1af4:1001]
Subsystem: Red Hat, Inc Device [1af4:0002]
Physical Slot: 5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c000 [size=64]
Region 1: Memory at fc023000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] MSI-X: Enable+ Count=2 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Kernel driver in use: virtio-pci
00:06.0 SCSI storage controller [0100]: Red Hat, Inc Virtio block device
[1af4:1001]
Subsystem: Red Hat, Inc Device [1af4:0002]
Physical Slot: 6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at c040 [size=64]
Region 1: Memory at fc024000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] MSI-X: Enable+ Count=2 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Kernel driver in use: virtio-pci
00:07.0 Ethernet controller [0200]: Red Hat, Inc Virtio network device
[1af4:1000]
Subsystem: Red Hat, Inc Device [1af4:0001]
Physical Slot: 7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c100 [size=32]
Region 1: Memory at fc025000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fc010000 [disabled] [size=64K]
Capabilities: [40] MSI-X: Enable+ Count=3 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Kernel driver in use: virtio-pci
** USB devices:
not available
-- System Information:
Debian Release: jessie/sid
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'unstable'), (500, 'testing'),
(500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.14-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.16-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.53
ii initramfs-tools [linux-initramfs-tool] 0.116
ii kmod 18-1
ii linux-base 3.5
ii module-init-tools 18-1
Versions of packages linux-image-3.16-1-amd64 recommends:
ii firmware-linux-free 3.3
Versions of packages linux-image-3.16-1-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-11
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16-1-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16-1-amd64/prerm/removing-running-kernel-3.16-1-amd64: true
linux-image-3.16-1-amd64/postinst/mips-initrd-3.16-1-amd64:
linux-image-3.16-1-amd64/postinst/depmod-error-initrd-3.16-1-amd64: false
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
