Package: installation-reports Debian-installer-version: 2005-10-31, 3.1r0a netinst image from cdimage.debian.org uname -a: Linux ptdslnx 2.6.8-2-32-smp #1 SMP Mon Feb 7 22:19:10 EST 2005 parisc GNU/Linux Date: 2005-10-31 13:30 EST Method: installed base system from CD; didn't try network install yet
Machine: HP Visualize B2000 Processor: 400MHz PA8600 (PCX-W+) Memory: 256M Root Device: /dev/mapper/vg00-root Root Size/partition table: Disk /dev/sda: 17366 cylinders, 64 heads, 32 sectors/track Warning: The partition table looks like it was made for C/H/S=*/255/63 (instead of 17366/64/32) For this listing I'll assume that geometry. Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0 Device Boot Start End #cyls #blocks Id System /dev/sda1 0+ 7 8- 64228+ f0 Linux/PA-RISC boot /dev/sda2 8 128 122 979965 83 Linux /dev/sda3 130 2212 2083 16731697+ 8e Linux LVM /dev/sda4 0 - 0 0 0 Empty # /dev/sda2 = /boot; the rest are LVs created from a PV on /dev/sda3 Output of lspci and lspci -n: 0000:00:0c.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41) 0000:00:0d.0 Multimedia audio controller: Analog Devices AD1889 sound chip 0000:00:0e.0 IDE interface: National Semiconductor Corporation 87415/87560 IDE (rev 03) 0000:00:0e.1 Bridge: National Semiconductor Corporation 87560 Legacy I/O (rev 01) 0000:00:0e.2 USB Controller: National Semiconductor Corporation USB Controller (rev 02) 0000:00:0f.0 SCSI storage controller: LSI Logic / Symbios Logic 53c895a (rev 01) 0000:01:00.0 3D Controller: Hewlett-Packard Company Visualize FXe (rev 03) 0000:00:0c.0 0200: 1011:0019 (rev 41) 0000:00:0d.0 0401: 11d4:1889 0000:00:0e.0 0101: 100b:0002 (rev 03) 0000:00:0e.1 0680: 100b:000e (erv 01) 0000:00:0e.2 0c03: 100b:0012 (rev 02) 0000:00:0f.0 0100: 1000:0012 (rev 01) 0000:01:00.0 0302: 103c:108b (rev 03) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [E] Configure network HW: [ ] Config network: [ ] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: Had to increase the ramdisk_size to 64M at the PALO prompt before install would work. Otherwise it ran out of room during startup and went into a loop, unable to find the net/unix/unix.ko kernel module. modprobe: FATAL: Could not open '/lib/modules/2.6.8-2-32/kernel/net/unix/unix.ko': No such file or directory On a separate note, during installation, text entry fields and the progress bars were all misaligned by one tty column to the right relative to their frames. Additionally, when a default value was supplied, its first character would remain as a "dropping" to the left of the entry field during editing.
