Package: src:linux
Version: 3.2.46-1
Severity: important
Dear Debian Linux Kernel Maintainers,
Systems using hpt302/htp302n cards don't boot after upgrading from
Squeeze to Wheezy. These cards used to be supported by the 2.6
kernel's hpt366 module but the 3.2 kernel's pata_hpt366 module
doesn't do the job, nor does the pata_hpt37x.
The kernel needs to be built with the pata_3x2n module enabled
(config PATA_HPT3X2N). This fixes the problem.
--Mike
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82875P/E7210 Memory Controller
Hub [8086:2578] (rev 02)
Subsystem: Intel Corporation 82875P/E7210 Memory Controller Hub
[8086:2578]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information: Len=06 <?>
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 82875P Processor to AGP Controller
[8086:2579] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:03.0 PCI bridge [0604]: Intel Corporation 82875P/E7210 Processor to PCI to
CSA Bridge [8086:257b] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: fc800000-fc8fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:06.0 System peripheral [0880]: Intel Corporation 82875P/E7210 Processor to
I/O Memory Interface [8086:257e] (rev 02)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K]
00:1d.0 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at cc00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 00007000-0000bfff
Memory behind bridge: fc900000-feafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller
[8086:24d1] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e400 [size=8]
Region 3: I/O ports at e000 [size=4]
Region 4: I/O ports at dc00 [size=16]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller [8086:24d3] (rev 02)
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at c800 [size=32]
Kernel driver in use: i801_smbus
02:01.0 Ethernet controller [0200]: Intel Corporation 82547EI Gigabit Ethernet
Controller [8086:1019]
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fc8e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 6c00 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Kernel driver in use: e1000
03:00.0 RAID bus controller [0104]: HighPoint Technologies, Inc. HPT302/302N
[1103:0006] (rev 02)
Subsystem: HighPoint Technologies, Inc. Device [1103:0001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 120 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at a800 [size=256]
Expansion ROM at feaa0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: HPT366_IDE
03:01.0 RAID bus controller [0104]: HighPoint Technologies, Inc. HPT302/302N
[1103:0006] (rev 02)
Subsystem: HighPoint Technologies, Inc. Device [1103:0001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 120 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at a400 [size=8]
Region 1: I/O ports at a000 [size=4]
Region 2: I/O ports at 9c00 [size=8]
Region 3: I/O ports at 9800 [size=4]
Region 4: I/O ports at 9400 [size=256]
Expansion ROM at fea80000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_hpt3x2n
03:02.0 RAID bus controller [0104]: HighPoint Technologies, Inc. HPT302/302N
[1103:0006] (rev 02)
Subsystem: HighPoint Technologies, Inc. Device [1103:0001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 120 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 9000 [size=8]
Region 1: I/O ports at 8c00 [size=4]
Region 2: I/O ports at 8800 [size=8]
Region 3: I/O ports at 8400 [size=4]
Region 4: I/O ports at 8000 [size=256]
Expansion ROM at fea60000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_hpt3x2n
03:06.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI
Rage XL [1002:4752] (rev 27) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at b800 [size=256]
Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
03:08.0 Ethernet controller [0200]: Intel Corporation 82562EZ 10/100 Ethernet
Controller [8086:1050] (rev 01)
Subsystem: Intel Corporation Device [8086:3428]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at feafe000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 7c00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0
"TetraHub"
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 046d:c312 Logitech, Inc. DeLuxe 250 Keyboard
-- System Information:
Debian Release: 7.1
APT prefers stable-updates
APT policy: (900, 'stable-updates'), (900, 'stable')
Architecture: i386 (i686)
Kernel: Linux 3.2.46 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-686-pae recommends:
ii firmware-linux-free 3.2
ii libc6-i686 2.13-38
Versions of packages linux-image-3.2.0-4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.36+wheezy.1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-686-pae/postinst/depmod-error-initrd-3.2.0-4-686-pae:
false
linux-image-3.2.0-4-686-pae/prerm/removing-running-kernel-3.2.0-4-686-pae:
true
linux-image-3.2.0-4-686-pae/postinst/missing-firmware-3.2.0-4-686-pae:
linux-image-3.2.0-4-686-pae/postinst/ignoring-ramdisk:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
