Package: firmware-brcm80211 This is a brand new wheezy installation on my new laptop (DELL Precision M6700).
After following: http://wiki.debian.org/brcm80211 Here is what I have: $ sudo modinfo brcmsmac filename: /lib/modules/3.2.0-4-amd64/kernel/drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.ko license: Dual BSD/GPL description: Broadcom 802.11n wireless LAN driver. author: Broadcom Corporation alias: pci:v000014E4d00000576sv*sd*bc*sc*i* alias: pci:v000014E4d00004727sv*sd*bc*sc*i* alias: pci:v000014E4d00004353sv*sd*bc*sc*i* alias: pci:v000014E4d00004357sv*sd*bc*sc*i* depends: mac80211,brcmutil,cfg80211,cordic,crc8 intree: Y vermagic: 3.2.0-4-amd64 SMP mod_unload modversions However: $ sudo lspci -s 03:00.0 -vvx 03:00.0 Network controller: Broadcom Corporation BCM43228 802.11a/b/g/n Subsystem: Dell Device 0014 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 10 Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=2 PME- Capabilities: [58] Vendor Specific Information: Len=78 <?> Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [d0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L1, Latency L0 <4us, L1 <64us ClockPM+ Surprise- LLActRep+ BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [13c v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- Capabilities: [160 v1] Device Serial Number 00-00-e2-ff-ff-75-f4-b7 Capabilities: [16c v1] Power Budgeting <?> 00: e4 14 59 43 06 00 10 00 00 00 80 02 10 00 00 00 10: 04 00 d0 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 14 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00 lshw also reveals: *-network UNCLAIMED description: Network controller product: BCM43228 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7d00000-f7d03fff Is there a way for me to track what could possibly be going on wrong with setup of wireless driver ? Thanks -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
