Package: src:linux
Version: 3.2.35-2
Severity: normal
Dear Maintainer,
I have got the following message at various points: E: linux-
image-3.2.0-4-amd64: subprocess installed post-installation script returned
error exit status 2
E: initramfs-tools: subprocess installed post-installation script returned
error exit status 1
I am running wheezy, installed from the liveCD, on a samsung RV520 laptop.
It happens mostly when trying to do stuff using apt/apt-get/synaptic etc.
It seems to sometimes stop it happening, although I'm not sure what it stops
happening.
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-ker...@lists.debian.org) (gcc version 4.6.3
(Debian 4.6.3-14) ) #1 SMP Debian 3.2.35-2
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64
root=UUID=5b179def-c2ca-4294-a4cd-c7cfaa3899a2 ro quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 791.020482] usb 1-1.4: reset high-speed USB device number 3 using ehci_hcd
[ 791.112142] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 791.118915] ata2.00: configured for UDMA/100
[ 791.120107] ata5: SATA link down (SStatus 0 SControl 300)
[ 791.128249] ata4: SATA link down (SStatus 0 SControl 300)
[ 793.397632] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 793.409988] ata1.00: configured for UDMA/133
[ 793.452329] PM: resume of devices complete after 2685.407 msecs
[ 793.452406] PM: Finishing wakeup.
[ 793.452408] Restarting tasks ... done.
[ 793.454334] usb 2-1.3: USB disconnect, device number 3
[ 793.457477] video LNXVIDEO:01: Restoring backlight state
[ 793.742159] r8169 0000:02:00.0: eth0: link down
[ 793.742166] r8169 0000:02:00.0: eth0: link down
[ 793.742561] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 793.905151] usb 2-1.3: new full-speed USB device number 5 using ehci_hcd
[ 794.001028] usb 2-1.3: New USB device found, idVendor=8086, idProduct=0189
[ 794.001032] usb 2-1.3: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 796.809079] r8169 0000:02:00.0: eth0: link up
[ 796.809426] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 807.554014] eth0: no IPv6 routers present
[ 824.309829] reportbug[4528] trap divide error ip:7f30c576f470
sp:7f30bddf8e00 error:0 in libgtk-x11-2.0.so.0.2400.10[7f30c563d000+432000]
[ 837.239399] reportbug[4542] trap divide error ip:7f8f99e1f470
sp:7f8f924a8e00 error:0 in libgtk-x11-2.0.so.0.2400.10[7f8f99ced000+432000]
[ 1228.486022] reportbug[4554] trap divide error ip:7faf2993d470
sp:7faf21fc6e00 error:0 in libgtk-x11-2.0.so.0.2400.10[7faf2980b000+432000]
[ 9308.284177] PM: Syncing filesystems ... done.
[ 9308.286025] PM: Preparing system for mem sleep
[ 9308.561560] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 9308.577421] Freezing remaining freezable tasks ... (elapsed 0.01 seconds)
done.
[ 9308.593405] PM: Entering mem sleep
[ 9308.593473] Suspending console(s) (use no_console_suspend to debug)
[ 9308.593836] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 9308.593901] sd 0:0:0:0: [sda] Stopping disk
[ 9309.656397] PM: suspend of devices complete after 1064.002 msecs
[ 9309.656527] r8169 0000:02:00.0: wake-up capability enabled by ACPI
[ 9309.672775] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[ 9309.688443] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[ 9309.704315] PM: late suspend of devices complete after 47.967 msecs
[ 9309.704560] ACPI: Preparing to enter system sleep state S3
[ 9309.724385] PM: Saving platform NVS memory
[ 9309.727206] Disabling non-boot CPUs ...
[ 9309.728986] CPU 1 is now offline
[ 9309.832071] CPU 2 is now offline
[ 9309.935941] CPU 3 is now offline
[ 9309.936456] Extended CMOS year: 2000
[ 9309.936779] ACPI: Low-level resume complete
[ 9309.936821] PM: Restoring platform NVS memory
[ 9309.937516] Extended CMOS year: 2000
[ 9309.937553] Enabling non-boot CPUs ...
[ 9309.937677] Booting Node 0 Processor 1 APIC 0x1
[ 9309.937679] smpboot cpu 1: start_ip = 98000
[ 9309.948696] Calibrating delay loop (skipped) already calibrated this CPU
[ 9309.948711] Disabled fast string operations
[ 9309.969039] NMI watchdog enabled, takes one hw-pmu counter.
[ 9309.969351] CPU1 is up
[ 9309.969479] Booting Node 0 Processor 2 APIC 0x2
[ 9309.969481] smpboot cpu 2: start_ip = 98000
[ 9309.980497] Calibrating delay loop (skipped) already calibrated this CPU
[ 9309.980511] Disabled fast string operations
[ 9310.000878] NMI watchdog enabled, takes one hw-pmu counter.
[ 9310.001182] CPU2 is up
[ 9310.001352] Booting Node 0 Processor 3 APIC 0x3
[ 9310.001354] smpboot cpu 3: start_ip = 98000
[ 9310.012370] Calibrating delay loop (skipped) already calibrated this CPU
[ 9310.012383] Disabled fast string operations
[ 9310.032857] NMI watchdog enabled, takes one hw-pmu counter.
[ 9310.033226] CPU3 is up
[ 9310.036747] ACPI: Waking up from system sleep state S3
[ 9310.117315] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[ 9310.117517] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[ 9310.118139] PM: early resume of devices complete after 0.964 msecs
[ 9310.118196] i915 0000:00:02.0: setting latency timer to 64
[ 9310.118205] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 9310.118209] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 9310.118243] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 9310.118263] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[ 9310.118270] ahci 0000:00:1f.2: setting latency timer to 64
[ 9310.118289] r8169 0000:02:00.0: wake-up capability disabled by ACPI
[ 9310.132847] sd 0:0:0:0: [sda] Starting disk
[ 9310.368769] usb 1-1.4: reset high-speed USB device number 3 using ehci_hcd
[ 9310.460448] ata4: SATA link down (SStatus 0 SControl 300)
[ 9310.468439] ata5: SATA link down (SStatus 0 SControl 300)
[ 9310.476412] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9310.483244] ata2.00: configured for UDMA/100
[ 9312.745947] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 9312.758320] ata1.00: configured for UDMA/133
[ 9312.803743] PM: resume of devices complete after 2688.529 msecs
[ 9312.803821] PM: Finishing wakeup.
[ 9312.803823] Restarting tasks ...
[ 9312.804553] usb 2-1.3: USB disconnect, device number 5
[ 9312.809489] done.
[ 9312.811737] video LNXVIDEO:01: Restoring backlight state
[ 9313.126502] r8169 0000:02:00.0: eth0: link down
[ 9313.126520] r8169 0000:02:00.0: eth0: link down
[ 9313.127756] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9313.257599] usb 2-1.3: new full-speed USB device number 6 using ehci_hcd
[ 9313.353166] usb 2-1.3: New USB device found, idVendor=8086, idProduct=0189
[ 9313.353171] usb 2-1.3: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 9316.155091] r8169 0000:02:00.0: eth0: link up
[ 9316.155433] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9326.386897] eth0: no IPv6 routers present
** Model information
sys_vendor: SAMSUNG ELECTRONICS CO., LTD.
product_name: RV420/RV520/RV720/E3530/S3530/E3420/E3520
product_version: 0.1
chassis_vendor: SAMSUNG ELECTRONICS CO., LTD.
chassis_version: 0.1
bios_vendor: Phoenix Technologies Ltd.
bios_version: 04PQ
board_vendor: SAMSUNG ELECTRONICS CO., LTD.
board_name: RV420/RV520/RV720/E3530/S3530/E3420/E3520
board_version: FAB1
** Loaded modules:
parport_pc
ppdev
lp
parport
rfcomm
bnep
binfmt_misc
uinput
loop
vmsync(O)
vmhgfs(O)
vmci(O)
fuse
uvcvideo
videodev
v4l2_compat_ioctl32
media
snd_hda_codec_hdmi
snd_hda_codec_realtek
iwlwifi
i915
snd_hda_intel
snd_hda_codec
joydev
snd_hwdep
snd_pcm
mac80211
snd_page_alloc
drm_kms_helper
drm
cfg80211
i2c_algo_bit
snd_seq
snd_seq_device
snd_timer
snd
btusb
bluetooth
soundcore
coretemp
iTCO_wdt
iTCO_vendor_support
samsung_laptop
rfkill
crc32c_intel
ghash_clmulni_intel
i2c_i801
cryptd
i2c_core
acpi_cpufreq
mperf
psmouse
evdev
ac
battery
processor
serio_raw
pcspkr
button
video
power_supply
ext4
crc16
jbd2
mbcache
sg
sr_mod
sd_mod
cdrom
crc_t10dif
usbhid
hid
ahci
libahci
libata
scsi_mod
ehci_hcd
thermal
fan
thermal_sys
r8169
mii
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor
Family DRAM Controller [8086:0104] (rev 09)
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core
Processor Family Integrated Graphics Controller [8086:0116] (rev 09) (prog-if
00 [VGA controller])
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 3000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series
Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0605000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f060a000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset
Family High Definition Audio Controller [8086:1c20] (rev 04)
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 42
Region 0: Memory at f0600000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 1 [8086:1c10] (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f0500000-f05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 4 [8086:1c16] (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Prefetchable memory behind bridge: 00000000f0400000-00000000f04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0609000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC
Controller [8086:1c49] (rev 04)
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset
Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 41
Region 0: I/O ports at 3088 [size=8]
Region 1: I/O ports at 3094 [size=4]
Region 2: I/O ports at 3080 [size=8]
Region 3: I/O ports at 3090 [size=4]
Region 4: I/O ports at 3060 [size=32]
Region 5: Memory at f0608000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family
SMBus Controller [8086:1c22] (rev 04)
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f0604000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
01:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 130
[8086:0896] (rev 34)
Subsystem: Intel Corporation Centrino Wireless-N 130 BGN [8086:5005]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0500000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)
Subsystem: Samsung Electronics Co Ltd Device [144d:c597]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at 2000 [size=256]
Region 2: Memory at f0404000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f0400000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 2232:1020
Bus 002 Device 006: ID 8086:0189 Intel Corp.
Bus 002 Device 004: ID 03f0:8207 Hewlett-Packard FHA-3510 2.4GHz Wireless
Optical Mobile Mouse
-- System Information:
Debian Release: 7.0
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_GB.utf8, LC_CTYPE=en_GB.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ih initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-23.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
